Home Repairing performances of novel cement mortar modified with graphene oxide and polyacrylate polymer
Article Open Access

Repairing performances of novel cement mortar modified with graphene oxide and polyacrylate polymer

  • Yibo Gao , Jianlin Luo EMAIL logo , Jigang Zhang , Xiaoyang Zhou , Fei Teng , Changquan Liu and Xijie Sun
Published/Copyright: April 22, 2022
Download Article (PDF)
Become an author with De Gruyter Brill
Submit Manuscript Author Information
Nanotechnology Reviews
From the journal Nanotechnology Reviews Volume 11 Issue 1

Abstract

Most cementitious repair materials have non-ignorable drawbacks such as low strength, insufficient bonding, and low anti-permeability. Although the bonding and anti-permeability of repair mortars modified by polymer will be substantially improved, the compressive strength and component integrity will be decreased. Hereby six groups of cement mortars modified by varied dosages of Graphene Oxide (GO) and PA copolymer (GOPARMs) were prepared. The flexural strength (f t), compressive strength (f c), f t/f c, bond strength (f b), and chloride ion migration coefficient (λ c) of GOPARMs were systematically studied by axial compressive, three-bending, pull-out, RCM method, along with microstructure analysis. When GO and PA dosages are fixed at 0.03 and 5 wt%, respectively, the f t, f c, f t/f c, f b, and λ c of GOPARMs reach the best comprehensive performances, which are 6.4, 46.5, 0.14, 6.73 MPa, and 1.179 × 10−12 m2/s. Compared with the control mortar, the f t, f c, f t /f c, and f b of GOPARMs are improved by 5.7, 12.3, 7, and 103%, respectively, and the corresponding λ c is dramatically reduced by 40.4%. Scanning electron microscope (SEM) shows that trace of GO can play a template nucleation effect on the hydration products’ morphology and microstructure of GOPARMs. Meanwhile, cured PA polymer can form hydrophobic film and fill the interfacial pores among hydration products, finally superior repairing performances of GOPARMs with optimal mix can be achieved.

Graphical abstract

Keywords: structural repair; interface bonding; nano-modified polymer mortar

1 Introduction

With the large-scale construction of concrete infrastructure in China, cement production has increased year by year, where large amounts of carbon dioxide greenhouse gas are emitted. The concrete structure under harsh environment cannot reach the expected durability, which will shorten its service life. However, rebuilding and reconstruction will bring forth more carbon emissions. Actually, using high-performance repair materials to repair and strengthen the original damaged parts or cracks of concrete structure is more cost-effective and eco-environmental compared to the traditional rebuilding and reconstruction. The repaired structure can continuously hinder the invasion of external harmful substances and the service life can be effectively prolonged [1,2,3,4,5,6,7,8,9].

In order to achieve good compatibility with the original concrete structure, the cement-based repair mortars are often chosen as the repair materials [10,11,12,13,14,15]. But lots of weak interfaces, cracks and breaks, stain residues, low strength concrete, etc., exist in the old structure substrate, for which it is difficult to achieve structural interface repair and rapid strengthening effect with ordinary cement repair mortar. Many scholars studied the repair performance of Portland cement-based repair mortars on the substrate concrete. They found that its bond strength (f b) on the substrate was not strong, and a non-negligible gap existed when the concrete dried and shrunk at different times, which jeopardized the wholeness between common repair mortars and old substrates [16,17]. Therefore, there is an urgent need to develop a special repair mortar with multi-functional performance such as fast-setting, high strength, low shrinkage, well-compatibility, and superior durability.

It is well known that viscous polymer latex can significantly improve the interfacial bond performance as frequently reported [18,19,20]. Compared to UHPC or ECC repair materials, the polymer-modified repair materials generally possess superior surface hydrophobic behavior, higher ductility, superior resistance to chloride ion permeability or corrosion, and lower shrinkage, whereas with relatively lower mechanical strength [21,22,23,24]. So, polymer-modified repair material is suitable to serve as high-performance cement-based repair materials [25,26]. In the 1980s, Ohama [27] and Konietzko [28] proposed the polymer netlike formation model and the dual web model in cement mortar, respectively. Ohama argued that the polymer would wrap a film around the hardened cement paste, while Grosskurth and Konietzko argued that the polymer and cement paste would interpenetrate and form a network structure. Today there are two main views on polymer-modified cement mortars (PCMs). One is based on the physical behavior of the polymer latex during the hydration of the cement [29,30]. During the hydration process, the polymer creates a network structure on the surfaces of the hydration products and cement particles or fills in the cracks of the cementitious material to improve its pore structure. The other view is that there is a physical interaction and chemical reaction between the polymer latex and the cement hydration, and the chemical reaction is a coordination reaction between Ca2+ within the cementitious material and the polymer directly to improve the final performance through chemical bonding [31,32,33,34,35,36,37]. Kim [20] compared the bond strength of different materials modified repair mortars. The 28-day bond strength of styrene-butadiene rubber (SBR) modified repair mortar was 29% higher than the control group, which was the best result among all the materials. Yang et al. [22] evaluated the chloride permeability and microstructure of Portland cement mortar modified by SBR latex. The study showed that SBR can improve the resistance of cement mortars to chloride ion permeability and can bind hydration products. Jiang et al. [23] reported that the mortar mixed with polyacrylate latex (PA) and silica fume (SF) had high bond strength and excellent durability performance compared with the control mortar without PA and SF. It is worth noting that most studies have shown that the mechanical properties of PCMs dosed with some polymer latex in general reduced, especially dramatic decreases in compressive strength (f c) [38,39,40,41]. Tian et al. [42] modified cementitious materials by using four organic polymers, namely silicone propylene latex, benzene propylene latex, waterborne epoxy latex, and acrylic latex, and revealed that most types of latex adversely affected the compressive properties of the cementitious materials. The f c and flexural strength (f t) of the cementitious materials with 5 wt% dosage of polyacrylic latex decreased by about 28.0–31 MPa and 9.1–6 MPa, respectively. Pei et al. [43] tested the mechanical properties of PA-modified mortars with different monomer ratios and found that the f c of the modified mortar decreased by more than 50% when dosed with methyl methacrylate. Tian et al. [44] found that excessive PA addition significantly reduced the mechanical properties of the cement mortar, and the 28 days f c of mortar specimens mixed with 10 wt% PA was only about 36 MPa. Ma and Li [45] found that the f c of the mortar dosed with 10% PA decreased by 11.7% compared to the control mortar. Obviously, the f c of PCM is still eager to substantial enhancement to achieve superior repairing property.

The dense microstructure of cement-based composites is the foundation for achieving high strength, toughness, and durability [46,47,48,49]. Therefore, the study of pursuing novel materials to regulate hydration products of cement-based composite has attracted considerable attentions. The employment of carbon nanotubes, graphene oxide (GO), and other materials can effectively toughen the cementitious materials [50,51,52,53,54,55]. Especially, GO possessing many oxygen-containing functional groups, high surface area, and amphiphilic hybrid sp2 structure, can exert its active template and nucleation effect at very low dosage [56,57,58,59], and it can assume to have the role of template in the hydration products of the cementitious materials, accelerate the hydration rate, reshape the microstructure, and control the distribution of hydration products and form a regular and orderly microstructure [60,61,62,63,64]. Some scholars have found that suitable GO dose can significantly improve the tensile strength [65], f c and f t [66] of the cementitious materials, improve the microstructure [67] and durability [68], and reduce the expansion rate [52]. Meanwhile, the functional groups such as hydroxyl, carbonyl, and carboxyl groups of GO itself make it easy to react with organic polymers, and the reacted GO can also be effectively dispersed in cement matrix to embody its excellent properties in the corresponding composite [69,70].

Here combined with the merits of two kinds of materials, GO/acrylate polymer-modified repair mortar (GOPARMs) by hybridization of GO and PA was first prepared. The f t, f c, flexural-compressive strength ratio (f t/f c), bond strength, resistance to chloride ion permeability, and microstructure of GOPARMs were also systematically investigated, to evaluate the practicability of GOPARMs as a novel repair material with excellent toughness, adhesion, and resistance to chloride ion permeability.

2 Materials and testing methods

2.1 Materials and mix ratio design

The chemical composition of cement (C), 42.5 grade high-belite sulfur-aluminate cement (HBSAC), produced by Tangshan Polar Bear Cement Plant Co., is shown in Table 1. Sand (S), ordinary river sand, locally available, with fineness modulus of 2.64, medium sand, mud content of less than 1.0% after rinsing treatment, in accordance with the requirements of DL/T 5126-2001 [71] was used. Superplasticizer (Sup), polycarboxylic superplasticizer with 30% water reduction rate, produced by Shandong Academy of Construction Sciences was procured. Polyacrylate latex (PA), obtained from the polymerization of acrylic monomer, was purchased from Beijing Mengtai Weiye Building Materials Co., Ltd, its main characteristics are shown in Table 2. Polyether modified silicone defoamer, B-364 type, was purchased from Guangdong China-union Fine Chemical Co. GO suspension with 10 mg/mL concentration, with 49–56% carbon and 41–50% oxygen content, was purchased from Nanjing Xianfeng Nanomaterials Technology Company. Distilled water (W), homemade was available.

Table 1

Main chemical composition of HBSAC

Cement type CaO SiO2 Al2O3 SO3 Fe2O3 MgO R2O Loss
HBSAC 41.97 18.33 16.63 14.97 1.00 5.34 0.78 0.15
Table 2

Main physicochemical properties of polyacrylate latex

Appearance Solid content (wt%) Main monomer pH Minimum film-forming temperature (℃) Vitrification temperature (℃) Viscosity (MPa s)
Milk-white liquid 55 ± 1 Acrylic acid 7–9 20 105 50

The PA latex and GO dosages were calculated according to the solid content of PA and GO, respectively. The mix ratio was referred to the previous experimental results of Luo et al. [72] and fixed at (C + PA):S:W = 1:1.7:0.4 after allowing for the water content in the PA and GO. Table 3 shows the experimental mix ratios and specimen grouping of GOPARMs.

Table 3

Experimental mix ratio design of GOPARMs (unit: kg/m3)

Item no.# C S PA GO W Sup Defoamer
P0G0 625 1,063 0 0 250 1.3 0
P5G0 31.3 0 262.5 1.3 0.2
P5G1 31.3 0.065 262.5 1.3 0.2
P5G3 31.3 0.196 262.5 1.3 0.2
P5G5 31.3 0.328 262.5 1.3 0.2
P10G0 62.5 0 275 1.4 0.4
P10G1 62.5 0.068 275 1.4 0.4
P10G3 62.5 0.206 275 1.4 0.4
P10G5 62.5 0.343 275 1.4 0.4
P20G0 125 0 300 1.5 0.8
P20G1 125 0.075 300 1.5 0.8
P20G3 125 0.225 300 1.5 0.8
P20G5 125 0.375 300 1.5 0.8

#Noting, P20G1 means GOPARMs with PA and GO dosage being 20 and 0.01%, respectively, the others are named by analogy.

2.2 Test apparatus and instruments

The main apparatus and instruments included: cement mortar mixer with a blade, ISO-679 type, Wuxi Jianding Construction Instrument Factory; TIP Ultrasonic pulverizer, FS-200T type, Shanghai ShengXi Ultrasonic Instrument Co., Ltd; electro-hydraulic universal machine, DYE-300 type, Wuxi Emino Testing Machine Co., Ltd; field emission scanning electron microscope, ISM-7610F type, Japan Electronics Inc.; magnetic stirrer, X85-2 type, Shanghai Meiyingpu Instrument Manufacturing Co., Ltd; electric thermostatic water bath, HHD-2 type, Shanghai Bilang Instrument Manufacturing Co., Ltd; vacuum drying oven, DHG-9030A type, Shanghai Jinghong Experimental Equipment Co., Ltd.

2.3 Preparation and experimental methods

2.3.1 Preparation of GO/PA suspension

The GO dispersion, Sup, and remaining water (total water required for the design ratio minus the water contained in PA and GO) were mixed in a beaker and sonicated for 20 min (sonication power 100 W and frequency 40 kHz); PA was added to the dispersed GO solution and magnetically stirred for 10 min, and the GO/PA suspension was accordingly prepared as reserved.

2.3.2 Preparation of substrate specimens for bond bending test

The bending bond strength (f b) test was referred to JC/T 2381-2016 [73]. It is worth to note that in order to keep the moisture content and the roughness of bonding interface of the substrate as consistent as possible for different experimental groups of the substrates, we improved to the preparation process of the substrates. The specimen with the size of 40 × 40 × 160 mm was sawed into two splits of 40 × 40 × 80 ± 2 mm blocks using a cutting machine, and the cut surfaces of the test block were lightly polished using an angle grinder to make each cut surface to have the same interface roughness. The polished test blocks were oven-dried at 105 ± 2℃ until the weight was unchanged, and then they were immersed in water to saturate, and their saturation rates were calculated. The substrate test blocks were oven-dried at 105 ± 2 ℃ until its water content was between 55 and 65%. The test blocks were film sealed and left to stand for 2 days.

2.3.3 Preparation of GOPARMs specimens

GOPARMs was prepared according to the pre-designed ratio with reference to the preparation method specified in GB/T17671-1999 [74]. The cement, water, and sand were first mixed at 40 rpm for 2 min at low speed; GO/PA suspension was subsequently mixed into the above mixture for 2 min at low speed, then stirred rapidly at 80 rpm for 30 s, and the defoamer was dipped to eliminate the air bubble; after that, the well-mixed slurry was poured into the molds of varied sizes (40 mm × 40 mm × 160 mm, φ100 mm × 50 mm), vibrated about 60 times on a mortar jump table to compact and facilitate the possible air bubble escaping from the slurry. The mortar surface was smoothed and film covered, and the GOPARMs specimens were removed after 5 h setting and standard curing till 7 days of age. The preparation process of GOPARMs is shown in detail in Figure 1.

Figure 1 Preparation process of GOPARMs.
Figure 1

Preparation process of GOPARMs.

2.3.4 Characterization of cured GOPARMs specimens

Compressive and flexural strength tests for the specimens with size of 40 mm × 40 mm × 160 mm was referred to GB/T17671-1999 [74], as shown in Figure 2(a), and the average experimental data of three specimens in each group represent the final result. The resistance to chloride ion permeability test was referred to GB/T50082-2009 [75], as shown in Figure 2(b), and the data are processed in the same way as the previous one. The bending bond strength (f b) test was referred to JC/T 2381-2016 [73], the f b was expressed by the interfacial bending strength between GOPARM specimens and old substrates, and tested by testing the f t of 40 mm × 40 mm × 160 mm specimens bonded by GOPARMs to the substrate specimens. As shown in Figure 2(c), there are six specimens in each group, and the measured data are averaged by possibly removing the maximum and the minimum value with 15% float above or below to the average, and taking the average of the remaining, and the calculation results are accurate to 0.01 MPa.

Figure 2 Photos of GOPARMs specimens: (a) compressive and flexural strength test (red arrow-prism); (b) resistance to chloride ion permeability test (blue arrow-cylinder); (c) bending bond test (green rectangular-new/old interface).
Figure 2

Photos of GOPARMs specimens: (a) compressive and flexural strength test (red arrow-prism); (b) resistance to chloride ion permeability test (blue arrow-cylinder); (c) bending bond test (green rectangular-new/old interface).

Finally, some tiny cubes from the fracture section of GOPARMs in No. P0G0 and P5G3 were observed with field-emitting scanning electron microscopy (FESEM) to analyze the effect of PA and GO on the microstructure of the corresponding mortar.

3 Results and discussion

3.1 Mechanical strength

The effects of PA and GO dosage on the mechanical properties (f cs and f ts) of GOPARMs are shown in Figure 3.

Figure 3 Variation curves of 7 days f cs and f ts of GOPARMs with different PA and GO dosages: (a) f c; (b) f t.
Figure 3

Variation curves of 7 days f cs and f ts of GOPARMs with different PA and GO dosages: (a) f c; (b) f t.

From Figure 3(a), under the condition of the same GO dosage, the higher the PA dosage is, the lower is the f c of GOPARMs, when the PA dosage reaches 20 wt%, the f c of GOPARMs is only about 16 MPa. While under the condition of the same PA dosage, the f c of GOPARMs increases along with GO dosage. When GO dosing is 0.03 wt% and PA dosing is 5%, the corresponding f c reaches the maximum value of 46.5 MPa, which is 4.5% higher than that of ordinary mortar without GO or PA dosing (44.5 MPa). And it’s noting, the f c of GOPARMs has somewhat decrease when GO dosage continues to increase.

It can be seen from Figure 3(b) that under the same condition of GO dosage, the f t of GOPARMs altered with PA dosage is different from that of f c. In the case of low PA dosage (5 wt%), the f t of GOPARMs increases, and its f t reaches the maximum 6.7 MPa when GO dosage is 0.03 wt%, which is almost 20% improvement with respect to the plain mortar (5.6 MPa) without any PA and GO; as the PA dosage continues to increase, the f t enhancement gradually decreases. And under the same condition of PA dosage, the effect of GO on the f t of GOPARMs has the same trend as its effect on its f c. Under the condition of low dosage of PA (lower than 0.03 wt%), the higher the GO dosage is, the higher is the f t of GOPARMs, whereas when the GO dosage climbs up to 0.05 wt%, the corresponding f t decreases significantly.

Obviously, at the optimal dosages of 5 wt% PA and 0.03 wt% GO, the corresponding f c and f t are 46.5 and 6.4 MPa, respectively.

As known, PA dosage has a negative effect on the f c of GOPARMs. Actually, with the hydration reaction of cement, PA will form polymer films staggered inside the mortar or wrap the hydration products. As shown in Figure 4(a) and the yellow circles in Figure 4(b), there exists obvious milky white films in the specimens with 5 wt% PA dosage, but not in the control specimen without PA dosage. Because the elastic modulus of the polymer film is much lower than that of the main product C–S–H gel, after the cement mortar is hardened, it leads to the reduction in the elastic modulus, and the f c of GOPARMs. In addition, the loading of viscous polymer will inevitably introduce air bubbles, as shown by the red rectangles in Figure 4(b). Although appropriate amount of defoamer has been added, still the air-entraining effect of the polymer cannot be avoided, and the introduction of larger pore size bubbles will increase the porosity of the mortar, so the f c of GOPARMs will have an unignorable drop with high polymer dosage.

Figure 4 Classic section morphology of GOPARMs: (a) P0G0 group (red arrows–pores); (b) P5G3 group (yellow circles: polymer films and; red rectangles: air bubbles).
Figure 4

Classic section morphology of GOPARMs: (a) P0G0 group (red arrows–pores); (b) P5G3 group (yellow circles: polymer films and; red rectangles: air bubbles).

It is worth noting that there exists an obvious increase (7%) in f t of GOPARMs at low PA dosage (0 wt% GO dosage). This is because as the hydration reaction of cement proceeds, PA can form a film inside the mortar to fill the small gaps between or wrap the hydration products, which are attached to the surface of the cementitious gel and improves the bulk flexural strength (f t) and toughness (f t /f c) of the final mortar. When the filling and wrapping effect of the polymer reaches saturation, the f t of cement mortar reaches the highest. However, if the polymer dosage continues to increase, the hydration products per unit area decreases, resulting in a decrease in the continuity between hydration products per unit area, the polymer will overwhelm the cement particles, thus affecting the hydration degree [45], and the corresponding macroscopic f c and f t of the cement mortar decrease. In addition, the air-entraining effect of polymer will also have a negative impact on the f c and f t of the cement mortar, as shown by Figure 4(a) and (b). Accordingly, the microstructure in group No. P5G3 specimen has much more air bubbles than that in No. P0G0 group.

Obviously, the increase in f c and f t at low GO dosage is owing to the nucleation effect and reshaped microstructure of GO on cement hydration products. It can render AFt, AFm, AH, CH, and C–S–H gel to form regular and orderly arrangements through the templating effect of GO itself, forming flower-shaped or multifaceted shape crystals or gels [34,62,63]. These crystals or gels mostly grow in the pores or loose positions in the mortar structure and are mutually connected with each other, with the tendency to form a network, which in turn increases the f c and f t of the mortar. With the continuous increase in GO dosage, the dispersion effect of GO is insufficient and agglomeration phenomenon may occur, which will lead to the accumulation and irregular arrangement of hydration products, and the bridging capacity between hydration decreases, its f c and f t accordingly falls down [64,69].

3.2 Fracture toughness

The fracture toughness of GOPARMs can be characterized by its ratio of f t /f c, with higher f t /f c indicating superior fracture toughness of the composite [76].

Figure 5 shows the changes in the f t /f c of GOPARMs with different dosage of PA and GO. It can be seen that the f t /f c of the composite gradually increases with the increase in PA dosage, and the variation in f t /f c is great in the range of 0–10 wt% dosage (f t /f c increased by 74.6, 63.1, 63.1, and 46.9% at 0, 0.01, 0.03, and 0.05 wt% GO dosage, respectively), while it is relatively low in the range of 10–20 wt% dosage (f t /f c increased by - 6.6, 15.6, 0.5, and 2.1% at 0, 0.01, 0.03, and 0.05 wt% GO dosage, respectively). This indicates that the fracture toughness of GOPARMs can be effectively improved with the appropriate dosage of PA. Actually, PA itself has very good deformability, it can well fill the small pores inside the GOPARMs, suitable PA dosage renders GOPARMs to have superior fracture toughness [43].

Figure 5 Variation curve of 7 days f t /f c of GOPARMs with different PA and GO dosages.
Figure 5

Variation curve of 7 days f t /f c of GOPARMs with different PA and GO dosages.

Figure 5 also shows that there is no significant variation in the f t /f c of GOPARMs with GO dosage under the same PA dosage condition. It shows that the GO dosage has no significant effect on the f t /f c of GOPARMs. In terms of f t /f c, the optimal dosage of PA and GO are 20 and 0.01 wt%, respectively, the corresponding f t /f c is 0.245. It should be noted that at this dosage level, the corresponding f c of GOPARMs decreases significantly owing to low elastic modulus of PA at high dosage.

3.3 Interfacial bond strength

3.3.1 Effect of PA dosage on the f b of GOPARMs

As shown in Figure 6, the f b of GOPARMs with the substrate is significantly enhanced by low PA dosage, and the most obvious improvement effect is achieved by 5 wt% PA dosage. Without any GO dosage, the f b of GOPARMs increases by about 39% with respect to the baseline; whereas with the addition of 0.03 wt% GO, the f b reaches the maximum value (6.73 MPa), which is about 103% enhancement compared with the baseline group. It is worth to note that with higher PA dosage, the increment amplitude of f b of the GOPARMs also decreases. When the PA dosage is 10 wt%, the f b of the specimens without GO dosage increases by about 36% compared with the baseline; when the GO dosage is 0.03 wt%, it accordingly increases by about 45% compared with the baseline. While the f b of the specimens is even lower than that of the baseline when the PA dosage reaches 20 wt%.

Figure 6 7 days f b change in GOPARMs along with different PA and GO dosages.
Figure 6

7 days f b change in GOPARMs along with different PA and GO dosages.

The f b of mortar with low PA dosage increases because the polymer in the mortar can penetrate into the pores of the mortar, rendering the contact surface of the old and new test blocks more tightly connected, so the f b of the mortar will be elevated. When PA dosage keeps increasing, the content of the cementitious material in the mortar decreases and the polymer content increases, the bonding performance of the cement mortar decreases when the f b of the cementitious material decreases to a greater extent than the f b provided by the polymer.

3.3.2 Effect of GO on the f b of GOPARMs

From Figure 6, the f b of GOPARMs and the substrate will be enhanced with a small amount of GO, and the enhancement effect on the f b of GOPARMs is related to PA dosage. The best strengthening effect of GO on the f b of the specimen can be achieved when the PA dosage is 5 wt%, and the f b gradually increases up to 6.73 MPa when the GO dosage is between 0 and 0.03 wt%. While GO dosage continues to increase, the corresponding f b steadily decreases. Under the condition of 10 wt% PA dosage, the f b gradually increases up to 4.82 MPa when GO dosage is between 0 and 0.03 wt%, and when the GO dosage continues to increase, the f b starts to decrease, and sharply drops down to 4.00 MPa. Under the condition of 20 wt% PA dosage, the GO dosage has no obvious effect on the improvement of the bonding performance, and even causes a significant decrease in the f b.

The mechanism of GO enhancing the f b of GOPARMs is similar to that of enhancing the f c of GOPARMs, which can induce the generation of flower-shaped and polyhedral crystals at the pores and cracks in the cementitious composites, thereby reduce the pores and cracks, and significantly improve the strength, toughness, and interface adhesion of the mortar.

In terms of f b, 5 wt% PA and 0.03 wt% GO are the optimal dosage, for the f b of GOPARMs to reach up to 6.73 MPa.

3.4 Chlorine ion permeation resistance performance of GOPARMs

Figure 7 shows the rapid chloride ion migration coefficient method (RCM) test operation and the color rendering diagram of chloride ion permeation of specimens. Seven groups of specimens were selected for this test, namely No. P0G0, P5G0, P5G1, P5G3, P5G5, P10G0, and P20G0, and the mix ratios of each group are shown in Table 3. The effect of GO and PA dosages on the resistance to chloride ion permeability of mortar was investigated by analyzing the chloride ion migration coefficients (λ c) of No. P5G0, P5G1, P5G3, P5G5, P0G0, P10G0, and P20G0, respectively.

Figure 7 RCM test procedure of GOPARMs: (a) rubber sleeve installation; (b) power penetration; (c) section color change after spraying silver nitrate.
Figure 7

RCM test procedure of GOPARMs: (a) rubber sleeve installation; (b) power penetration; (c) section color change after spraying silver nitrate.

The λ c is calculated according to equation (1):

(1) D RCM = 0.0239 × ( 273 + T ) L ( U − 2 ) t × X d − 0.0238 ( 273 + T ) L X d U − 2 ,

where, D RCM – non-stationary λ c of concrete, accurate to 0.1 × 10−12 m2/s; U – absolute value of the voltage used (V); T – average of the initial and ending temperatures of the anode solution (°C); L – specimen thickness (mm), accurate to 0.1 mm; X d – average value of chloride ion penetration depth (mm), accurate to 0.1 mm; t – test duration (h).

3.4.1 Effect of PA dosage on the resistance to chloride ion permeability of GOPARMs

As seen from Figure 8, with the increase in PA dosage, the λ c first gradually decreases, and when the PA dosage increases to 5 wt% (GO dosage 0), the λ c is the smallest, only 1.495 × 10−12 m2/s, which is 24.3% less than that of the specimens without PA dosage (P0G0). Continuing to increase the PA dosage, the λ c of GOPARMs gradually increases, and when the PA dosage reaches 20 wt% (GO dosage 0.03 wt%), the λ c reaches 29.763 × 10−12 m2/s, which is much larger than that of the blank group. Therefore, an adequate amount of PA can improve the resistance to chloride ion permeability of mortar to a certain extent, but too large PA dosage will have a negative effect on the impermeability of the mortar.

Figure 8 Effect of PA and GO dosage on the λ c of GOPARMs.
Figure 8

Effect of PA and GO dosage on the λ c of GOPARMs.

The reason why fewer PA can increase the resistance to chloride ion permeability of mortar is that the polymer can penetrate into the pores of the mortar, and cement hydration absorbs the water from outside and the water in PA. The organic polymer film can be formed after the PA dries, and this film has a good filling effect on the small pores and improves the material resistance to chloride ion penetration. It is worth noting that the addition of too much PA will make the mortar very viscous, and many larger air bubbles will be introduced during the preparation of mortar specimens, which leads to a reduction in the compactness and resistance to chloride ion permeability.

3.4.2 Effect of GO dosage on the resistance to chloride ion permeability of GOPARMs

From Figure 8, we can clearly observe that with the increase in GO dosage, the λ c decreased first, and the smallest λ c of 1.179 × 10−12 m2/s was obtained when the GO dosage was 0.03 wt% (PA dosage 5 wt%), which was about 13.6% lower than that of the P5G0 group without GO dosage. However, when the GO dosage was increased to 0.05 wt%, the λ c increased again to 1.934 × 10−12 m2/s, which was 41.8% higher than that of P5G0. The above experimental phenomenon indicates that the addition of a small amount of GO can reduce the λ c of the specimens, i.e., the resistance to chloride ion permeability is improved, but the excessive amount of GO will adversely affect the resistance to chloride ion permeability of the specimens.

The effect of change in GO on the microstructure of mortar can explain the above situation well. Low amount of GO has good active template and nucleation effect, which can effectively improve the arrangement structure of hydration products, reduce the pore structure inside GOPARMs, and improve the impermeability of the mortar. Excessive amount of GO is not easy to disperse in the cementitious materials, and agglomerated GO cannot play its excellent performance, but will lead to the agglomeration and accumulation of hydration products, reduce the connection between hydration crystals, and the internal compactness of GOPARMs to be reduced, which is not conducive to its impermeability performance.

In terms of the resistance to chloride ion permeability, 5 wt% PA and 0.03 wt% GO are the optimal dosage, respectively, and the corresponding λ c of GOPARMs is 1.179 × 10−12 m2/s.

3.5 Micromorphological analysis of GOPARMs

In order to observe the microscopic morphology of GOPARMs and further verify the microscopic mechanism of the changes in its mechanical properties, bonding properties, and resistance to chloride ion penetration, in this study, the cross-sections were observed by field-emitting scanning electron microscopy.

3.5.1 Micromechanical analysis of PA to improve the performance of GOPARMs

Figure 9 shows the microscopic morphology of hydration products of GOPARMs with different PA admixtures. The blank group in Figure 9(a) shows typical cement hydration products, including needle-rod AFt, amorphous AFm, CH, AH, and bulk C–S–H gels with a relatively loose structure and more voids and cracks. In Figure 9(b), with PA dosage of 5 wt%, PA has obviously played a role in filling the pores and connecting the hydration products, the gel structure is obviously denser compared to the blank group, and the polymer starts to form a small amount of encapsulation on the hydration products. In Figure 9(c), the presence of continuous rod-like gels can be clearly observed with PA dosage of 10 wt%, and these gels are mixed gels of polymer and hydration products, i.e., the polymer has obvious encapsulation connection to the needle and rod-like hydration products. However, some of the gels intertwined with the cement hydration products appeared to be agglomerated into clumps, which produced fine cracks compared to GOPARMs with 5 wt% PA dosage.

Figure 9 Morphology of hydration products of GOPARMs with different PA dosage (yellow circles: AFt; red rectangles: other amorphous hydration products; green pentagon: AFt wrapped in PA; blue triangles: agglomerates composed of hydration products and PA): (a) without PA dosage; (b) PA dosage 5 wt%; (c) PA dosage 10 wt%.
Figure 9

Morphology of hydration products of GOPARMs with different PA dosage (yellow circles: AFt; red rectangles: other amorphous hydration products; green pentagon: AFt wrapped in PA; blue triangles: agglomerates composed of hydration products and PA): (a) without PA dosage; (b) PA dosage 5 wt%; (c) PA dosage 10 wt%.

The results of the different elemental contents detected in the orange marked points of PA-modified mortars in Figure 9(c) are given in Table 4. It can be found that the C/O is about 0.13, which is much higher than the C/O of ordinary cementitious materials [34]. Moreover, Ca, Si, S, and Al in the mortars, which are the key elements that constitute the hydration products of SAC, can also be detected by EDS. The junction and the EDS and SEM test results can prove that the hydration products of the cementitious materials and PA mixed with each other. And PA can fill the voids between the hydration products or encapsulate the hydration products.

Table 4

EDS analysis of PA modified mortars from Figure 9(c) (wt%)

Chemical element C O Al Si S Ca
Atom content (wt%) 9.3 71.5 5.1 1.9 4.6 7.6

After microscopic tests, it is difficult to observe a very obvious polymer film formation regardless of the PA dosage, and it is speculated that the improving mechanism of the PA on the performance is not the one proposed by most scholars to enhance the macroscopic performance of mortar by forming a good integral polymer film between hydration products [77,78,79]. Tian et al. [34] demonstrated that PA can complexation react with Ca2+ within the cementitious materials to generate calcium carboxylate functional groups, which can enhance the properties of the cementitious materials through chemical bonding. In summary, a small amount of PA can not only improve the compactness of mortar material by filling the internal pores of GOPARMs but also enhance the material properties by forming ligand bonds through chemical reactions, the specific complexation reactions are shown in Figure 10. However, the large amount of PA will lead to the increase in large internal pores due to the air-entraining effect of PA, which will reduce the degree of material compactness and adversely affect the performance of GOPARMs.

Figure 10 Reactions between Ca2+ and polyacrylate (PA) polymer chain: (a) self-link of polymer chain; (b) cross-link of PA polymer chains; (c) cross-link between PA polymer chain and cement hydrates.
Figure 10

Reactions between Ca2+ and polyacrylate (PA) polymer chain: (a) self-link of polymer chain; (b) cross-link of PA polymer chains; (c) cross-link between PA polymer chain and cement hydrates.

3.5.2 Micromechanical analysis of GO to improve the performance of GOPARMs

Some scholars have found that GO can be modified by Sup or PA through non-covalent or covalent bonding modifications during physical mixing [69,80,81]. It can effectively improve the dispersion of GO, which is the basis for GO to exert its excellent performance [82].

Figure 11 shows the morphology of hydration products of GOPARMs doped with 0.03 wt% GO. It can be clearly seen that the internal hydration products of mortar are denser and more orderly after GO dosage. This will lead to a significant increase in the denseness of the cement mortar material, which is beneficial to the improvement of the macroscopic properties of the material. The dense and orderly distribution of hydration products is due to the small amount of GO in GOPARMs which exerts active template and nucleation effect. The high specific surface area of GO provides a good nucleation structure for the orderly growth of hydration products, and GO itself can also play a good filling and linking effect between hydration products and cement particles, optimizing the three-dimensional network structure inside GOPARMs. Therefore, GO can play a good toughening and densification effect on GOPARMs, which can effectively improve the mechanical properties and impermeability of the material [83,84,85,86].

Figure 11 Morphology of hydration products of GOPARMs doped with 0.03 wt% GO (very dense and orderly distribution of hydration products): (a) ×5k; (b) ×10k (yellow circles: AFt and red rectangles: other amorphous hydration products).
Figure 11

Morphology of hydration products of GOPARMs doped with 0.03 wt% GO (very dense and orderly distribution of hydration products): (a) ×5k; (b) ×10k (yellow circles: AFt and red rectangles: other amorphous hydration products).

It is concluded that all the properties of GOPARMs meet the specification requirements, and its f b and λ c are significantly superior to those of the ordinary repair mortar, which is suitable as a cost-effective repair and reinforcement material application in concrete structure.

4 Conclusion

In this article, GO dispersion and PA were physically blended and the GO/PA mixture was synergistically modified cement mortar, and the mortar was characterized with mechanical and durability behavior (f c, f t, f t/f c, f b, and λ c). Some results are concluded:

  1. With the increase in PA dosage, the f c of mortar steadily decreases, and the f t/f c steadily increases, but the f t, f b, and λ c of the mortar first increases and then decreases.

  2. With the increase in GO dosage, the f c, f t, and f b of mortar are all up first and then down, yet the trend of f t/f c is not obvious, the optimal GO dosage is at 0.03 wt%.

  3. The doped GO can play an active template and nucleation effect among the hydration products of GOPARMs, resulting in improved texture and microstructure; while the doped PA can encapsulate the hydration products to a certain extent, playing the role of filling the internal pores and connections, and forming coordination bonds between the hydration products, thereby improving the mechanical toughness, bonding, and resistance to chloride ion permeability of GOPARMs.

  4. After comprehensive consideration, the f c, f t, f t/f c, f b, and λ c of GOPARMs with the dosage of 5 wt% PA and 0.03 wt% GO reach 46.5 MPa, 6.4 MPa, 0.14, 6.73 MPa, and 1.179 × 10−12 m2/s, respectively, which are enhanced by 5.7, 12.3, 7, and 103%, and the corresponding λ c is reduced by 40.4%. Obviously, a cost-effective and competitive repair mortar with superior bonding and resistance to chloride ion permeability can be predicted.

tel: +86 532 8507 1605, fax: +86 532 8507 1605

Acknowledgments

The authors are obliged to thank for the reinforcement mechanism discussion with Prof. Qiuyi Li (Qingdao Agriculture University) and Prof. Jing Zhong (Harbin Institute of Technology (Shenzhen)).

  1. Funding information: This study was financially supported by NSFC-Shandong Province Joint Key Project (Grant No. U2106222), National Natural Science Foundation of China (No. 51878364), Key Technology Research and Development Program of Shandong Province (Public welfare type) (No. 2019GSF110008), and the National “111” project, and Gaofeng discipline project funded by Shandong Province.

  2. Author contributions: Jianlin Luo, Jigang Zhang: conceptualization, supervision, and resources; Yibo Gao, Jianlin Luo, and Xijie Sun: data curation, formal analysis, and methodology; Jianlin Luo, Changquan Liu, and Jigang Zhang: funding acquisition, investigation, and project administration; Yibo Gao and Jianlin Luo: validation, visualization, and writing - original draft; Yibo Gao, Jianlin Luo, Fei Teng, and Xiaoyang Zhou: writing - review and editing. All authors have accepted responsibility for the entire content of this manuscript and approved its submission.

  3. Conflict of interest: The authors state no conflict of interest.

References

[1] Pavlíková M, Zemanová L, Záleská M, Pokorný J, Lojka M, Jankovský O, et al. Ternary blended binder for production of a novel type of lightweight repair mortar. Mater. 2019;12(6):996.10.3390/ma12060996Search in Google Scholar PubMed PubMed Central

[2] Xia Q, Wen J, Tang X, Zhu Y, Xu Z, Du Z, et al. Optimal preparation and degradation characterization of repair mortar containing waterborne epoxy resin emulsions. Constr Build Mater. 2021;298:123839.10.1016/j.conbuildmat.2021.123839Search in Google Scholar

[3] Yang J, Wang R, Zhang Y. Influence of dually mixing with latex powder and polypropylene fiber on toughness and shrinkage performance of overlay repair mortar. Constr Build Mater. 2020;261:120521.10.1016/j.conbuildmat.2020.120521Search in Google Scholar

[4] Zanotti C, Borges PHR, Bhutta A, Banthia N. Bond strength between concrete substrate and metakaolin geopolymer repair mortar: effect of curing regime and PVA fiber reinforcement. Cem Concr Compos. 2017;80:307–16.10.1016/j.cemconcomp.2016.12.014Search in Google Scholar

[5] Jia L, Zhao F, Yao K, Du H. Bond performance of repair mortar made with magnesium phosphate cement and ferroaluminate cement. Constr Build Mater. 2021;279:122398.1–10.10.1016/j.conbuildmat.2021.122398Search in Google Scholar

[6] Oh H, Lee I. A Hardening and strength properties of magnesium phosphate mortars for rapid repair materials. J Korea Inst Struct Maintenance Inspection. 2019;23(3):103–10.Search in Google Scholar

[7] Feng S, Xiao H, Geng J. Bond strength between concrete substrate and repair mortar: effect of fibre stiffness and substrate surface roughness. Cem Concr Compos. 2020;114:103746.10.1016/j.cemconcomp.2020.103746Search in Google Scholar

[8] He J, Bu X, Bai W, Zheng W, Gao Q, Wang Y. Preparation and properties of self-compacting alkali-activated slag repair mortar. Constr Build Mater. 2020;252:119034.10.1016/j.conbuildmat.2020.119034Search in Google Scholar

[9] He Y, Zhang X, Hooton RD, Zhang X. Effects of interface roughness and interface adhesion on new-to-old concrete bonding. Constr Build Mater. 2017;151:582–90.10.1016/j.conbuildmat.2017.05.049Search in Google Scholar

[10] Okamoto PA, Whiting D. Use of maturity and pulse velocity techniques to predict strength gain of rapid concrete pavement repairs during curing period. Transport Res Rec. 1994;1458:85–90.Search in Google Scholar

[11] Chaunsali P, Mondal P. Physico-chemical interaction between mineral admixtures and OPC-calcium sulfoaluminate (CSA) cements and its influence on early-age expansion. Cem Concr Res. 2016;80:10–20.10.1016/j.cemconres.2015.11.003Search in Google Scholar

[12] Pelletier L, Winnefeld F, Lothenbach B. The ternary system Portland cement-calcium sulphoaluminate clinker-anhydrite: hydration mechanism and mortar properties. Cem Concr Compos. 2010;32(7):497–507.10.1016/j.cemconcomp.2010.03.010Search in Google Scholar

[13] Li J, Ji YS, Xu ZS. Microstructure evolution of interface between magnesium ammonium phosphate cement and Portland cement under sulphate corrosion environment. Sādhanā Published Ind Acad Sci. 2020;45(3):37–40.10.1007/s12046-020-01347-9Search in Google Scholar

[14] Park JW, Kim KH, Ann KY. Fundamental properties of magnesium phosphate cement mortar for rapid repair of concrete. Adv Mater Sci Eng. 2016;2016:1–7.10.1155/2016/7179403Search in Google Scholar

[15] Qin J, Qian J, You C, Fan Y, Li Z, Wang H. Bond behavior and interfacial micro-characteristics of magnesium phosphate cement onto old concrete substrate. Constr Build Mater. 2018;167:166–76.10.1016/j.conbuildmat.2018.02.018Search in Google Scholar

[16] Courard L, Lenaers JF, Michel F, Garbacz A. Saturation level of the superficial zone of concrete and adhesion of repair systems. Constr Build Mater. 2010;25(5):2488–94.10.1016/j.conbuildmat.2010.11.076Search in Google Scholar

[17] Kim G, Kim JY, Kurtis KE, Jacobs LJ. Drying shrinkage in concrete assessed by nonlinear ultrasound. Cem Concr Res. 2017;92:16–20.10.1016/j.cemconres.2016.11.010Search in Google Scholar

[18] Chung DDL. Use of polymers for cement-based structural materials. J Mater Sci. 2004;39(9):2973–8.10.1023/B:JMSC.0000025822.72755.70Search in Google Scholar

[19] Al-Zahrani MM, Maslehuddin M, Al-Dulaijan SU, Ibrahim M. Mechanical properties and durability characteristics of polymer-modified and cement-based repair materials. Cem Concr Compos. 2003;25(4):527–37.10.1016/S0958-9465(02)00092-6Search in Google Scholar

[20] Kim MO. Influence of polymer types on the mechanical properties of polymer-modified cement mortars. Appl Sci. 2020;10(3):1061.10.3390/app10031061Search in Google Scholar

[21] Lin JS. Preparation and properties of fiber-reinforced polymer cement waterproof slurry [dissertation]. Guangdong: South China University of Technology; 2015 (in Chinese).Search in Google Scholar

[22] Yang Z, Shi X, Creighton AT, Peterson MM. Effect of styrene–butadiene rubber latex on the chloride permeability and microstructure of Portland cement mortar. Constr Build Mater. 2009;23(6):2283–90.10.1016/j.conbuildmat.2008.11.011Search in Google Scholar

[23] Jiang C, Huang S, Gao P, Chen D. Experimental study on the bond and durability properties of mortar incorporating polyacrylic ester and silica fume. Adv Cem Res. 2018;30(2):56–65.10.1680/jadcr.17.00053Search in Google Scholar

[24] Xie T, Fang C, Mohamad Ali MS, Visintin P. Characterizations of autogenous and drying shrinkage of ultra-high performance concrete (UHPC): an experimental study. Cem Concr Compos. 2018;91:156–73.10.1016/j.cemconcomp.2018.05.009Search in Google Scholar

[25] Shi C, Wang P, Ma C, Zou X, Yang L. Effects of SAE and SBR on properties of rapid hardening repair mortar. J Build Eng. 2021;35:102000.10.1016/j.jobe.2020.102000Search in Google Scholar

[26] Kong XM, Wu CC, Zhang YR, Li JL. Polymer-modified mortar with a gradient polymer distribution: preparation, permeability, and mechanical behaviour. Constr Build Mater. 2013;38:195–203.10.1016/j.conbuildmat.2012.07.080Search in Google Scholar

[27] Ohama Y. Handbook of polymer-modified concrete and mortars: properties and process technology. London: William Andrew; 1995.10.1016/B978-081551373-5.50013-1Search in Google Scholar

[28] Grosskurth KP, Konietzko A. Structure and mechanical behaviour of polymer modified cement concrete. Proceeding of 5th International Congress on Polymers in Concrete. Brighton, UK: 1987. p. 171–4.Search in Google Scholar

[29] Mansur AAP, Santos DB, Mansur HS. A microstructural approach to adherence mechanism of poly(vinyl alcohol) modified cement systems to ceramic tiles. Cem Concr Res. 2007;37(2):270–82.10.1016/j.cemconres.2006.11.011Search in Google Scholar

[30] Afridi MUK, Ohama Y, Demura K, Iqbal MZ. Development of polymer films by the coalescence of polymer particles in powdered and aqueous polymer-modified mortars. Cem Concr Res. 2003;33(11):1715–21.10.1016/S0008-8846(02)01094-3Search in Google Scholar

[31] Jenni A, Zurbriggen R, Holzer L, Herwegh M. Changes in microstructures and physical properties of polymer-modified mortars during wet storage. Cem Concr Res. 2006;36(1):79–90.10.1016/j.cemconres.2005.06.001Search in Google Scholar

[32] Ma H, Tian Y, Li Z. Interactions between organic and inorganic phases in PA-and PU/PA-modified-cement-based materials. J Mater Civ Eng. 2011;23(10):1412–21.10.1061/(ASCE)MT.1943-5533.0000302Search in Google Scholar

[33] Tian Y, Jin X, Jin N, Zhao R, Li Z, Ma H. Research on the microstructure formation of polyacrylate latex modified mortars. Constr Build Mater. 2013;47:1381–94.10.1016/j.conbuildmat.2013.06.016Search in Google Scholar

[34] Tian Y, Li Z, Ma H, Jin N, Jin NG. An investigation on the microstructure formation of polymer modified mortars in the presence of polyacrylate latex. Proceedings of International RILEM Conference on Advances in Construction Materials Through Science and Engineering; 2011. p. 71–7.Search in Google Scholar

[35] Matsuyama H, Young JF. Synthesis of calcium silicate hydrate/polymer complexes: part I, Anionic and nonionic polymers. J Mater Res. 1999;14(8):3379–88.10.1557/JMR.1999.0458Search in Google Scholar

[36] Bonapasta AA, Buda F, Colombet P. Interaction between Ca ions and poly (acrylic acid) chains in macro-defect-free cements:  a theoretical study. Chem Mater. 2000;13(1):67–70.10.1021/cm000505oSearch in Google Scholar

[37] Bonapasta AA, Buda F, Pierre C. Cross-linking of poly(vinyl alcohol) chains by Ca ions in macro-defect-free cements. Chem Mater. 2002;14(3):1016–22.10.1021/cm010573qSearch in Google Scholar

[38] Heng YY, Zhao WJ. Research progress on the properties and mechanism of SAEE modified cement based materials. Bulletin of the Chinese Ceramic Society. 2014;33(06):1431–8 (in Chinese).Search in Google Scholar

[39] Li Y, Zhu JC, Wu YS. Effect of polymer on performance of ultra-high toughness cementitious composites. J Build Mater. 2018;21(1):26–32.Search in Google Scholar

[40] Wang R, Wang PM, Li XG. Physical and mechanical properties of styrene–butadiene rubber emulsion modified cement mortars. Cem Concr Res. 2005;35(5):900–6.10.1016/j.cemconres.2004.07.012Search in Google Scholar

[41] Bahranifard Z, Tabrizi FF, Vosoughi AR. An investigation on the effect of styrene-butyl acrylate copolymer latex to improve the properties of polymer modified concrete. Constr Build Mater. 2019;205:175–85.10.1016/j.conbuildmat.2019.01.175Search in Google Scholar

[42] Tian YL, Gao PW, Wang R, Wang LM, Zhong JJ, Li JS. Study on the influence of organic polymers on the physical and mechanical properties of cement-based materials, Tokyo University of Science, Tongji University. Proceedings of the 2nd International Conference on Environmental Prevention and Pollution Control Technologies (EPPCT2020). Tokyo University of Science, Tongji University: International Conference on Humanities and Social Science Research; 2020. p. 7.10.1088/1755-1315/474/7/072028Search in Google Scholar

[43] Pei M, Wu Y, Kim W, Wu Y, Kim W, Hyung W, et al. Effect of the monomer ratio on the properties of poly (methyl methacrylate butyl acrylate) latex‐modified mortars. J Appl Polym Sci. 2004;93(5):2403–9.10.1002/app.20744Search in Google Scholar

[44] Tian Y, Li ZJ, Jin XY. Mechanical characterization of polyacrylate emulsion modified mortars. Earth and space 2010: engineering, science, construction, and operations in challenging environments; 2010. p. 3567–78.10.1061/41096(366)342Search in Google Scholar

[45] Ma H, Li Z. Microstructures and mechanical properties of polymer modified mortars under distinct mechanisms. Constr Build Mater. 2013;47:579–87.10.1016/j.conbuildmat.2013.05.048Search in Google Scholar

[46] Shi JY, Liu BJ, Qin JL, Jang JY, Wu X, Tan JX. Experimental study of performance of repair mortar: evaluation of in-situ tests and correlation analysis. J Build Eng. 2020;31:101325.10.1016/j.jobe.2020.101325Search in Google Scholar

[47] Gao S, Li QY, Li N, et al. Research on super dense recycled mortar preparation based on densified parking theory. J Build Struc. 2021;42(S1):466–72.Search in Google Scholar

[48] Yang CJ. Research on properties and repair test of nano-modified polymer cementitious material [dissertation]. Zhejiang: Zhejiang University; 2016 (in Chinese).Search in Google Scholar

[49] Niaki MH, Fereidoon A, Ahangari MG. Experimental study on the mechanical and thermal properties of basalt fiber and nanoclay reinforced polymer concrete. Compos Struc. 2018;191:231–8.10.1016/j.compstruct.2018.02.063Search in Google Scholar

[50] Lu H, Yao Y, Huang WM, Hui D. Noncovalently functionalized carbon fiber by grafted self-assembled graphene oxide and the synergistic effect on polymeric shape memory nanocomposites. Compos Part B. 2014;67:290–5.10.1016/j.compositesb.2014.07.022Search in Google Scholar

[51] Cui HZ, Yang JM, Li JZ. Research progress on carbon nanotubes dispersion techniques and CNTs-reinforced cement-based materials. Mater Rep. 2016;30(2):91–5 (in Chinese).Search in Google Scholar

[52] Luo J, Zhou C, , Li W, Chen S, Habibnejad Korayem A, Duan W. Using graphene oxide to improve physical property and control ASR expansion of cement mortar. Constr Build Mater. 2021;308:125006.10.1016/j.conbuildmat.2021.125006Search in Google Scholar

[53] Luo J, Chen S, Li Q, Liu C, Gao S, Zhang J, et al. Influence of graphene oxide on mechanical properties, fracture toughness, and microhardness of recycled concrete. Nanomaterials. 2019;9:325–38.10.3390/nano9030325Search in Google Scholar PubMed PubMed Central

[54] Zhao Z, Qi T, Zhou W, Hui D, Xiao C, Qi J, et al. A review on the properties, reinforcing effects, and commercialization of nanomaterials for cement-based materials. Nanotechnol Rev. 2020;9:303–22.10.1515/ntrev-2020-0023Search in Google Scholar

[55] Daghash SM, Soliman EM, Kandil UF, Reda Taha MM. Improving impact resistance of polymer concrete using CNTs. Int J Concr Struct Mater. 2016;10(4):539–53.10.1007/s40069-016-0165-4Search in Google Scholar

[56] Zhu Y, Murali S, Cai W, Murali S, Cai W, Li X, et al. Graphene and graphene oxide: synthesis, properties, and applications. Adv Mater. 2010;22(35):3906–24.10.1002/adma.201001068Search in Google Scholar PubMed

[57] Ramezanzadeh M, Ramezanzadeh B, Sari MG, Ramezanzadeh B, Sari MG, Saeb MR. Corrosion resistance of epoxy coating on mild steel through polyamidoamine dendrimer-covalently functionalized graphene oxide nanosheets. J Ind Eng Chem. 2020;82:290–302.10.1016/j.jiec.2019.10.025Search in Google Scholar

[58] Shen L, Zou L, Ding M, Zou L, Ding M, Zhao T, et al. Investigation of physical properties of epoxy-functionalized graphene nanoplatelets composite coatings on DC-GIL insulators by molecular dynamics simulation. Appl Surf Sci. 2020;505:144197.10.1016/j.apsusc.2019.144197Search in Google Scholar

[59] Wu X, Field RW, Wu JJ, Field RW, Wu JJ, Zhang K. Polyvinylpyrrolidone modified graphene oxide as a modifier for thin film composite forward osmosis membranes. J Membr Sci. 2017;540:251–60.10.1016/j.memsci.2017.06.070Search in Google Scholar

[60] Guo SY, Zhang X, Chen JZ, Mou B, Shang HS, Wang P, et al. Mechanical and interface bonding properties of epoxy resin reinforced Portland cement repairing mortar. Constr Build Mater. 2020;264:120715.10.1016/j.conbuildmat.2020.120715Search in Google Scholar

[61] Zhao L. Effect of PC modified GO on the reinforcement of cement composites [dissertation]. Jiangsu: Southeast University; 2018 (in Chinese).Search in Google Scholar

[62] Li X, Liu YM, Li WG, Li CY, Sanjayan JG, Duan WH, et al. Effects of graphene oxide agglomerates on workability, hydration, microstructure and compressive strength of cement paste. Constr Build Mater. 2017;145:402–10.10.1016/j.conbuildmat.2017.04.058Search in Google Scholar

[63] Li W, Li X, Chen SJ, Liu YM, Duan WH, Shah SP. Effects of graphene oxide on early-age hydration and electrical resistivity of Portland cement paste. Constr Build Mater. 2017;136:506–14.10.1016/j.conbuildmat.2017.01.066Search in Google Scholar

[64] Lu Z, Chen B, Leung CY, Li Z, Sun G. Aggregation size effect of graphene oxide on its reinforcing efficiency to cement based materials. Cem Concr Compos. 2019;100:85–91.10.1016/j.cemconcomp.2019.04.005Search in Google Scholar

[65] Li X, Lu Z, Chuah S, Li W, Liu Y, Duan WH, et al. Effects of graphene oxide aggregates on hydration degree, sorptivity, and tensile splitting strength of cement paste. Compos Part A. 2017;100:1–8.10.1016/j.compositesa.2017.05.002Search in Google Scholar

[66] Hu M, Guo J, Fan J, li P, Chen D. Dispersion of triethanolamine-functionalized graphene oxide (TEA-GO) in pore solution and its influence on hydration, mechanical behavior of cement composite. Constr Build Mater. 2019;216:128–36.10.1016/j.conbuildmat.2019.04.180Search in Google Scholar

[67] Wang J, Xu Y, Wu X, Xu Y, Wu X, Zhang P, et al. Advances of graphene and graphene oxide modified cementitious materials. Nanotechnol Rev. 2020;9:465–77.10.1515/ntrev-2020-0041Search in Google Scholar

[68] Wang JK. Study on properties of graphene oxide modified cement-based composites materials [dissertation]. Hebei: Hebei University of Technology; 2018 (in Chinese).Search in Google Scholar

[69] Lv SH, Zhu LL, Jia CM, Li Y, He YY, Zhao HR. Influence of PCs/GO Composites on Microstructure and Mechanical Properties of Cement Based Materials. Mater Rev. 2017;31(06):125–9 + 135.Search in Google Scholar

[70] Wajid AS, Ahmed HST, Das S, Irin F, Jankowski AF, Green MJ. High-performance pristine graphene/epoxy composites with enhanced mechanical and electrical properties. Macromol Mater Eng. 2013;298(3):339–47.10.1002/mame.201200043Search in Google Scholar

[71] Test code on polymer-modified cement mortar (DL/T 5126-2001). Beijing: China Electric Power Press; 2001 (in Chinese).Search in Google Scholar

[72] Li H, Luo JL, Li QY, Liu C, Chen SC. Bonding repair and shrinkage durability of ductile fiber-reinforced polymer mortar. New Chem Mater. 2019;47(7):266–70 (in Chinese).Search in Google Scholar

[73] Repairing mortar (JC/T 2381-2016). Beijing: China Architecture & Building Press, 2016 (in Chinese).Search in Google Scholar

[74] Method of testing cements-Determination of strength (GB/T 17671-1999). Beijing: Standards Press of China; 1999 (in Chinese).Search in Google Scholar

[75] Standard for test methods of long-term performance and durability of ordinary concrete (GB/T 50082-2009). Beijing: China Architecture & Building Press; 2009 (in Chinese).Search in Google Scholar

[76] Luo J, Li Q, Zhao T, Gao S, Sun S. Bonding and toughness properties of PVA fibre reinforced aqueous epoxy resin cement repair mortar. Constr Build Mater. 2013;49:766–71.10.1016/j.conbuildmat.2013.08.052Search in Google Scholar

[77] Li B, Tian Y, Zhao RY, Duan A, Li ZJ, Ma HY. Microstructure and modification mechanism of polyacrylate latex modified motars. Journal of Zhejiang University. 2014;48(08):1345–52 + 1361 (in Chinese).Search in Google Scholar

[78] Plank J, Gretz M. Study on the interaction between anionic and cationic latex particles and Portland Cement. Colloids Surf A. 2008;330(2):227–33.10.1016/j.colsurfa.2008.08.005Search in Google Scholar

[79] Afridi MUK, Ohama Y, Demura K, Iqbal MZ. Development of polymer films by the coalescence of polymer particles in powdered and aqueous polymer-modified mortars. Cem Concr Res. 2003;33(11):1715–21.10.1016/S0008-8846(02)01094-3Search in Google Scholar

[80] Zhang WB. Preparation and properties of polyacrylate/modified graphene oxide composites [dissertation]. Shanxi: Shanxi University of Science and Technology; 2016 (in Chinese).Search in Google Scholar

[81] Wang D, Zhang X, Zha JW, Zhao J, Dang ZM, Hu GH. Dielectric properties of reduced graphene oxide/polypropylene composites with ultralow percolation threshold. Polym. 2013;54(7):1916–22.10.1016/j.polymer.2013.02.012Search in Google Scholar

[82] Gao Y, Jing HW, Chen SJ, Du MR, Chen WQ, Duan WH. Influence of ultrasonication on the dispersion and enhancing effect of graphene oxide–carbon nanotube hybrid nanoreinforcement in cementitious composite. Compos Part B. 2019;164:45–53.10.1016/j.compositesb.2018.11.066Search in Google Scholar

[83] Lv S, Ma Y, Qiu C, Sun T, Liu J, Zhou Q. Effect of graphene oxide nanosheets of microstructure and mechanical properties of cement composites. Constr Build Mater. 2013;49:121–7.10.1016/j.conbuildmat.2013.08.022Search in Google Scholar

[84] Lv SH, Liu JJ, Qiu CC, Ma YJ, Zhou QF. Microstructure and mechanism of reinforced and toughened cement composites by nanographene oxide. J Funct Mater. 2014;45(04):4084–9.Search in Google Scholar

[85] Babak F, Abolfazl H, Alimorad R, Parviz G. Preparation and mechanical properties of graphene oxide: cement nanocomposites. Sci World J. 2014;276233:1–10.10.1155/2014/276323Search in Google Scholar PubMed PubMed Central

[86] Saafi M, Tang L, Fung J, Rahman M, Liggat J. Enhanced properties of graphene/fly ash geopolymeric composite cement. Cem Concr Res. 2015;67:292–9.10.1016/j.cemconres.2014.08.011Search in Google Scholar
Received: 2021-11-21
Revised: 2021-12-17
Accepted: 2022-02-17
Published Online: 2022-04-22

© 2022 Yibo Gao et al., published by De Gruyter

This work is licensed under the Creative Commons Attribution 4.0 International License.

Articles in the same Issue

  1. Research Articles
  2. Theoretical and experimental investigation of MWCNT dispersion effect on the elastic modulus of flexible PDMS/MWCNT nanocomposites
  3. Mechanical, morphological, and fracture-deformation behavior of MWCNTs-reinforced (Al–Cu–Mg–T351) alloy cast nanocomposites fabricated by optimized mechanical milling and powder metallurgy techniques
  4. Flammability and physical stability of sugar palm crystalline nanocellulose reinforced thermoplastic sugar palm starch/poly(lactic acid) blend bionanocomposites
  5. Glutathione-loaded non-ionic surfactant niosomes: A new approach to improve oral bioavailability and hepatoprotective efficacy of glutathione
  6. Relationship between mechano-bactericidal activity and nanoblades density on chemically strengthened glass
  7. In situ regulation of microstructure and microwave-absorbing properties of FeSiAl through HNO3 oxidation
  8. Research on a mechanical model of magnetorheological fluid different diameter particles
  9. Nanomechanical and dynamic mechanical properties of rubber–wood–plastic composites
  10. Investigative properties of CeO2 doped with niobium: A combined characterization and DFT studies
  11. Miniaturized peptidomimetics and nano-vesiculation in endothelin types through probable nano-disk formation and structure property relationships of endothelins’ fragments
  12. N/S co-doped CoSe/C nanocubes as anode materials for Li-ion batteries
  13. Synergistic effects of halloysite nanotubes with metal and phosphorus additives on the optimal design of eco-friendly sandwich panels with maximum flame resistance and minimum weight
  14. Octreotide-conjugated silver nanoparticles for active targeting of somatostatin receptors and their application in a nebulized rat model
  15. Controllable morphology of Bi2S3 nanostructures formed via hydrothermal vulcanization of Bi2O3 thin-film layer and their photoelectrocatalytic performances
  16. Development of (−)-epigallocatechin-3-gallate-loaded folate receptor-targeted nanoparticles for prostate cancer treatment
  17. Enhancement of the mechanical properties of HDPE mineral nanocomposites by filler particles modulation of the matrix plastic/elastic behavior
  18. Effect of plasticizers on the properties of sugar palm nanocellulose/cinnamon essential oil reinforced starch bionanocomposite films
  19. Optimization of nano coating to reduce the thermal deformation of ball screws
  20. Preparation of efficient piezoelectric PVDF–HFP/Ni composite films by high electric field poling
  21. MHD dissipative Casson nanofluid liquid film flow due to an unsteady stretching sheet with radiation influence and slip velocity phenomenon
  22. Effects of nano-SiO2 modification on rubberised mortar and concrete with recycled coarse aggregates
  23. Mechanical and microscopic properties of fiber-reinforced coal gangue-based geopolymer concrete
  24. Effect of morphology and size on the thermodynamic stability of cerium oxide nanoparticles: Experiment and molecular dynamics calculation
  25. Mechanical performance of a CFRP composite reinforced via gelatin-CNTs: A study on fiber interfacial enhancement and matrix enhancement
  26. A practical review over surface modification, nanopatterns, emerging materials, drug delivery systems, and their biophysiochemical properties for dental implants: Recent progresses and advances
  27. HTR: An ultra-high speed algorithm for cage recognition of clathrate hydrates
  28. Effects of microalloying elements added by in situ synthesis on the microstructure of WCu composites
  29. A highly sensitive nanobiosensor based on aptamer-conjugated graphene-decorated rhodium nanoparticles for detection of HER2-positive circulating tumor cells
  30. Progressive collapse performance of shear strengthened RC frames by nano CFRP
  31. Core–shell heterostructured composites of carbon nanotubes and imine-linked hyperbranched polymers as metal-free Li-ion anodes
  32. A Galerkin strategy for tri-hybridized mixture in ethylene glycol comprising variable diffusion and thermal conductivity using non-Fourier’s theory
  33. Simple models for tensile modulus of shape memory polymer nanocomposites at ambient temperature
  34. Preparation and morphological studies of tin sulfide nanoparticles and use as efficient photocatalysts for the degradation of rhodamine B and phenol
  35. Polyethyleneimine-impregnated activated carbon nanofiber composited graphene-derived rice husk char for efficient post-combustion CO2 capture
  36. Electrospun nanofibers of Co3O4 nanocrystals encapsulated in cyclized-polyacrylonitrile for lithium storage
  37. Pitting corrosion induced on high-strength high carbon steel wire in high alkaline deaerated chloride electrolyte
  38. Formulation of polymeric nanoparticles loaded sorafenib; evaluation of cytotoxicity, molecular evaluation, and gene expression studies in lung and breast cancer cell lines
  39. Engineered nanocomposites in asphalt binders
  40. Influence of loading voltage, domain ratio, and additional load on the actuation of dielectric elastomer
  41. Thermally induced hex-graphene transitions in 2D carbon crystals
  42. The surface modification effect on the interfacial properties of glass fiber-reinforced epoxy: A molecular dynamics study
  43. Molecular dynamics study of deformation mechanism of interfacial microzone of Cu/Al2Cu/Al composites under tension
  44. Nanocolloid simulators of luminescent solar concentrator photovoltaic windows
  45. Compressive strength and anti-chloride ion penetration assessment of geopolymer mortar merging PVA fiber and nano-SiO2 using RBF–BP composite neural network
  46. Effect of 3-mercapto-1-propane sulfonate sulfonic acid and polyvinylpyrrolidone on the growth of cobalt pillar by electrodeposition
  47. Dynamics of convective slippery constraints on hybrid radiative Sutterby nanofluid flow by Galerkin finite element simulation
  48. Preparation of vanadium by the magnesiothermic self-propagating reduction and process control
  49. Microstructure-dependent photoelectrocatalytic activity of heterogeneous ZnO–ZnS nanosheets
  50. Cytotoxic and pro-inflammatory effects of molybdenum and tungsten disulphide on human bronchial cells
  51. Improving recycled aggregate concrete by compression casting and nano-silica
  52. Chemically reactive Maxwell nanoliquid flow by a stretching surface in the frames of Newtonian heating, nonlinear convection and radiative flux: Nanopolymer flow processing simulation
  53. Nonlinear dynamic and crack behaviors of carbon nanotubes-reinforced composites with various geometries
  54. Biosynthesis of copper oxide nanoparticles and its therapeutic efficacy against colon cancer
  55. Synthesis and characterization of smart stimuli-responsive herbal drug-encapsulated nanoniosome particles for efficient treatment of breast cancer
  56. Homotopic simulation for heat transport phenomenon of the Burgers nanofluids flow over a stretching cylinder with thermal convective and zero mass flux conditions
  57. Incorporation of copper and strontium ions in TiO2 nanotubes via dopamine to enhance hemocompatibility and cytocompatibility
  58. Mechanical, thermal, and barrier properties of starch films incorporated with chitosan nanoparticles
  59. Mechanical properties and microstructure of nano-strengthened recycled aggregate concrete
  60. Glucose-responsive nanogels efficiently maintain the stability and activity of therapeutic enzymes
  61. Tunning matrix rheology and mechanical performance of ultra-high performance concrete using cellulose nanofibers
  62. Flexible MXene/copper/cellulose nanofiber heat spreader films with enhanced thermal conductivity
  63. Promoted charge separation and specific surface area via interlacing of N-doped titanium dioxide nanotubes on carbon nitride nanosheets for photocatalytic degradation of Rhodamine B
  64. Elucidating the role of silicon dioxide and titanium dioxide nanoparticles in mitigating the disease of the eggplant caused by Phomopsis vexans, Ralstonia solanacearum, and root-knot nematode Meloidogyne incognita
  65. An implication of magnetic dipole in Carreau Yasuda liquid influenced by engine oil using ternary hybrid nanomaterial
  66. Robust synthesis of a composite phase of copper vanadium oxide with enhanced performance for durable aqueous Zn-ion batteries
  67. Tunning self-assembled phases of bovine serum albumin via hydrothermal process to synthesize novel functional hydrogel for skin protection against UVB
  68. A comparative experimental study on damping properties of epoxy nanocomposite beams reinforced with carbon nanotubes and graphene nanoplatelets
  69. Lightweight and hydrophobic Ni/GO/PVA composite aerogels for ultrahigh performance electromagnetic interference shielding
  70. Research on the auxetic behavior and mechanical properties of periodically rotating graphene nanostructures
  71. Repairing performances of novel cement mortar modified with graphene oxide and polyacrylate polymer
  72. Closed-loop recycling and fabrication of hydrophilic CNT films with high performance
  73. Design of thin-film configuration of SnO2–Ag2O composites for NO2 gas-sensing applications
  74. Study on stress distribution of SiC/Al composites based on microstructure models with microns and nanoparticles
  75. PVDF green nanofibers as potential carriers for improving self-healing and mechanical properties of carbon fiber/epoxy prepregs
  76. Osteogenesis capability of three-dimensionally printed poly(lactic acid)-halloysite nanotube scaffolds containing strontium ranelate
  77. Silver nanoparticles induce mitochondria-dependent apoptosis and late non-canonical autophagy in HT-29 colon cancer cells
  78. Preparation and bonding mechanisms of polymer/metal hybrid composite by nano molding technology
  79. Damage self-sensing and strain monitoring of glass-reinforced epoxy composite impregnated with graphene nanoplatelet and multiwalled carbon nanotubes
  80. Thermal analysis characterisation of solar-powered ship using Oldroyd hybrid nanofluids in parabolic trough solar collector: An optimal thermal application
  81. Pyrene-functionalized halloysite nanotubes for simultaneously detecting and separating Hg(ii) in aqueous media: A comprehensive comparison on interparticle and intraparticle excimers
  82. Fabrication of self-assembly CNT flexible film and its piezoresistive sensing behaviors
  83. Thermal valuation and entropy inspection of second-grade nanoscale fluid flow over a stretching surface by applying Koo–Kleinstreuer–Li relation
  84. Mechanical properties and microstructure of nano-SiO2 and basalt-fiber-reinforced recycled aggregate concrete
  85. Characterization and tribology performance of polyaniline-coated nanodiamond lubricant additives
  86. Combined impact of Marangoni convection and thermophoretic particle deposition on chemically reactive transport of nanofluid flow over a stretching surface
  87. Spark plasma extrusion of binder free hydroxyapatite powder
  88. An investigation on thermo-mechanical performance of graphene-oxide-reinforced shape memory polymer
  89. Effect of nanoadditives on the novel leather fiber/recycled poly(ethylene-vinyl-acetate) polymer composites for multifunctional applications: Fabrication, characterizations, and multiobjective optimization using central composite design
  90. Design selection for a hemispherical dimple core sandwich panel using hybrid multi-criteria decision-making methods
  91. Improving tensile strength and impact toughness of plasticized poly(lactic acid) biocomposites by incorporating nanofibrillated cellulose
  92. Green synthesis of spinel copper ferrite (CuFe2O4) nanoparticles and their toxicity
  93. The effect of TaC and NbC hybrid and mono-nanoparticles on AA2024 nanocomposites: Microstructure, strengthening, and artificial aging
  94. Excited-state geometry relaxation of pyrene-modified cellulose nanocrystals under UV-light excitation for detecting Fe3+
  95. Effect of CNTs and MEA on the creep of face-slab concrete at an early age
  96. Effect of deformation conditions on compression phase transformation of AZ31
  97. Application of MXene as a new generation of highly conductive coating materials for electromembrane-surrounded solid-phase microextraction
  98. A comparative study of the elasto-plastic properties for ceramic nanocomposites filled by graphene or graphene oxide nanoplates
  99. Encapsulation strategies for improving the biological behavior of CdS@ZIF-8 nanocomposites
  100. Biosynthesis of ZnO NPs from pumpkin seeds’ extract and elucidation of its anticancer potential against breast cancer
  101. Preliminary trials of the gold nanoparticles conjugated chrysin: An assessment of anti-oxidant, anti-microbial, and in vitro cytotoxic activities of a nanoformulated flavonoid
  102. Effect of micron-scale pores increased by nano-SiO2 sol modification on the strength of cement mortar
  103. Fractional simulations for thermal flow of hybrid nanofluid with aluminum oxide and titanium oxide nanoparticles with water and blood base fluids
  104. The effect of graphene nano-powder on the viscosity of water: An experimental study and artificial neural network modeling
  105. Development of a novel heat- and shear-resistant nano-silica gelling agent
  106. Characterization, biocompatibility and in vivo of nominal MnO2-containing wollastonite glass-ceramic
  107. Entropy production simulation of second-grade magnetic nanomaterials flowing across an expanding surface with viscidness dissipative flux
  108. Enhancement in structural, morphological, and optical properties of copper oxide for optoelectronic device applications
  109. Aptamer-functionalized chitosan-coated gold nanoparticle complex as a suitable targeted drug carrier for improved breast cancer treatment
  110. Performance and overall evaluation of nano-alumina-modified asphalt mixture
  111. Analysis of pure nanofluid (GO/engine oil) and hybrid nanofluid (GO–Fe3O4/engine oil): Novel thermal and magnetic features
  112. Synthesis of Ag@AgCl modified anatase/rutile/brookite mixed phase TiO2 and their photocatalytic property
  113. Mechanisms and influential variables on the abrasion resistance hydraulic concrete
  114. Synergistic reinforcement mechanism of basalt fiber/cellulose nanocrystals/polypropylene composites
  115. Achieving excellent oxidation resistance and mechanical properties of TiB2–B4C/carbon aerogel composites by quick-gelation and mechanical mixing
  116. Microwave-assisted sol–gel template-free synthesis and characterization of silica nanoparticles obtained from South African coal fly ash
  117. Pulsed laser-assisted synthesis of nano nickel(ii) oxide-anchored graphitic carbon nitride: Characterizations and their potential antibacterial/anti-biofilm applications
  118. Effects of nano-ZrSi2 on thermal stability of phenolic resin and thermal reusability of quartz–phenolic composites
  119. Benzaldehyde derivatives on tin electroplating as corrosion resistance for fabricating copper circuit
  120. Mechanical and heat transfer properties of 4D-printed shape memory graphene oxide/epoxy acrylate composites
  121. Coupling the vanadium-induced amorphous/crystalline NiFe2O4 with phosphide heterojunction toward active oxygen evolution reaction catalysts
  122. Graphene-oxide-reinforced cement composites mechanical and microstructural characteristics at elevated temperatures
  123. Gray correlation analysis of factors influencing compressive strength and durability of nano-SiO2 and PVA fiber reinforced geopolymer mortar
  124. Preparation of layered gradient Cu–Cr–Ti alloy with excellent mechanical properties, thermal stability, and electrical conductivity
  125. Recovery of Cr from chrome-containing leather wastes to develop aluminum-based composite material along with Al2O3 ceramic particles: An ingenious approach
  126. Mechanisms of the improved stiffness of flexible polymers under impact loading
  127. Anticancer potential of gold nanoparticles (AuNPs) using a battery of in vitro tests
  128. Review Articles
  129. Proposed approaches for coronaviruses elimination from wastewater: Membrane techniques and nanotechnology solutions
  130. Application of Pickering emulsion in oil drilling and production
  131. The contribution of microfluidics to the fight against tuberculosis
  132. Graphene-based biosensors for disease theranostics: Development, applications, and recent advancements
  133. Synthesis and encapsulation of iron oxide nanorods for application in magnetic hyperthermia and photothermal therapy
  134. Contemporary nano-architectured drugs and leads for ανβ3 integrin-based chemotherapy: Rationale and retrospect
  135. State-of-the-art review of fabrication, application, and mechanical properties of functionally graded porous nanocomposite materials
  136. Insights on magnetic spinel ferrites for targeted drug delivery and hyperthermia applications
  137. A review on heterogeneous oxidation of acetaminophen based on micro and nanoparticles catalyzed by different activators
  138. Early diagnosis of lung cancer using magnetic nanoparticles-integrated systems
  139. Advances in ZnO: Manipulation of defects for enhancing their technological potentials
  140. Efficacious nanomedicine track toward combating COVID-19
  141. A review of the design, processes, and properties of Mg-based composites
  142. Green synthesis of nanoparticles for varied applications: Green renewable resources and energy-efficient synthetic routes
  143. Two-dimensional nanomaterial-based polymer composites: Fundamentals and applications
  144. Recent progress and challenges in plasmonic nanomaterials
  145. Apoptotic cell-derived micro/nanosized extracellular vesicles in tissue regeneration
  146. Electronic noses based on metal oxide nanowires: A review
  147. Framework materials for supercapacitors
  148. An overview on the reproductive toxicity of graphene derivatives: Highlighting the importance
  149. Antibacterial nanomaterials: Upcoming hope to overcome antibiotic resistance crisis
  150. Research progress of carbon materials in the field of three-dimensional printing polymer nanocomposites
  151. A review of atomic layer deposition modelling and simulation methodologies: Density functional theory and molecular dynamics
  152. Recent advances in the preparation of PVDF-based piezoelectric materials
  153. Recent developments in tensile properties of friction welding of carbon fiber-reinforced composite: A review
  154. Comprehensive review of the properties of fly ash-based geopolymer with additive of nano-SiO2
  155. Perspectives in biopolymer/graphene-based composite application: Advances, challenges, and recommendations
  156. Graphene-based nanocomposite using new modeling molecular dynamic simulations for proposed neutralizing mechanism and real-time sensing of COVID-19
  157. Nanotechnology application on bamboo materials: A review
  158. Recent developments and future perspectives of biorenewable nanocomposites for advanced applications
  159. Nanostructured lipid carrier system: A compendium of their formulation development approaches, optimization strategies by quality by design, and recent applications in drug delivery
  160. 3D printing customized design of human bone tissue implant and its application
  161. Design, preparation, and functionalization of nanobiomaterials for enhanced efficacy in current and future biomedical applications
  162. A brief review of nanoparticles-doped PEDOT:PSS nanocomposite for OLED and OPV
  163. Nanotechnology interventions as a putative tool for the treatment of dental afflictions
  164. Recent advancements in metal–organic frameworks integrating quantum dots (QDs@MOF) and their potential applications
  165. A focused review of short electrospun nanofiber preparation techniques for composite reinforcement
  166. Microstructural characteristics and nano-modification of interfacial transition zone in concrete: A review
  167. Latest developments in the upconversion nanotechnology for the rapid detection of food safety: A review
  168. Strategic applications of nano-fertilizers for sustainable agriculture: Benefits and bottlenecks
  169. Molecular dynamics application of cocrystal energetic materials: A review
  170. Synthesis and application of nanometer hydroxyapatite in biomedicine
  171. Cutting-edge development in waste-recycled nanomaterials for energy storage and conversion applications
  172. Biological applications of ternary quantum dots: A review
  173. Nanotherapeutics for hydrogen sulfide-involved treatment: An emerging approach for cancer therapy
  174. Application of antibacterial nanoparticles in orthodontic materials
  175. Effect of natural-based biological hydrogels combined with growth factors on skin wound healing
  176. Nanozymes – A route to overcome microbial resistance: A viewpoint
  177. Recent developments and applications of smart nanoparticles in biomedicine
  178. Contemporary review on carbon nanotube (CNT) composites and their impact on multifarious applications
  179. Interfacial interactions and reinforcing mechanisms of cellulose and chitin nanomaterials and starch derivatives for cement and concrete strength and durability enhancement: A review
  180. Diamond-like carbon films for tribological modification of rubber
  181. Layered double hydroxides (LDHs) modified cement-based materials: A systematic review
  182. Recent research progress and advanced applications of silica/polymer nanocomposites
  183. Modeling of supramolecular biopolymers: Leading the in silico revolution of tissue engineering and nanomedicine
  184. Recent advances in perovskites-based optoelectronics
  185. Biogenic synthesis of palladium nanoparticles: New production methods and applications
  186. A comprehensive review of nanofluids with fractional derivatives: Modeling and application
  187. Electrospinning of marine polysaccharides: Processing and chemical aspects, challenges, and future prospects
  188. Electrohydrodynamic printing for demanding devices: A review of processing and applications
  189. Rapid Communications
  190. Structural material with designed thermal twist for a simple actuation
  191. Recent advances in photothermal materials for solar-driven crude oil adsorption
https://doi.org/10.1515/ntrev-2022-0091
Keywords for this article
structural repair; interface bonding; nano-modified polymer mortar
Creative Commons
BY 4.0

Articles in the same Issue

  1. Research Articles
  2. Theoretical and experimental investigation of MWCNT dispersion effect on the elastic modulus of flexible PDMS/MWCNT nanocomposites
  3. Mechanical, morphological, and fracture-deformation behavior of MWCNTs-reinforced (Al–Cu–Mg–T351) alloy cast nanocomposites fabricated by optimized mechanical milling and powder metallurgy techniques
  4. Flammability and physical stability of sugar palm crystalline nanocellulose reinforced thermoplastic sugar palm starch/poly(lactic acid) blend bionanocomposites
  5. Glutathione-loaded non-ionic surfactant niosomes: A new approach to improve oral bioavailability and hepatoprotective efficacy of glutathione
  6. Relationship between mechano-bactericidal activity and nanoblades density on chemically strengthened glass
  7. In situ regulation of microstructure and microwave-absorbing properties of FeSiAl through HNO3 oxidation
  8. Research on a mechanical model of magnetorheological fluid different diameter particles
  9. Nanomechanical and dynamic mechanical properties of rubber–wood–plastic composites
  10. Investigative properties of CeO2 doped with niobium: A combined characterization and DFT studies
  11. Miniaturized peptidomimetics and nano-vesiculation in endothelin types through probable nano-disk formation and structure property relationships of endothelins’ fragments
  12. N/S co-doped CoSe/C nanocubes as anode materials for Li-ion batteries
  13. Synergistic effects of halloysite nanotubes with metal and phosphorus additives on the optimal design of eco-friendly sandwich panels with maximum flame resistance and minimum weight
  14. Octreotide-conjugated silver nanoparticles for active targeting of somatostatin receptors and their application in a nebulized rat model
  15. Controllable morphology of Bi2S3 nanostructures formed via hydrothermal vulcanization of Bi2O3 thin-film layer and their photoelectrocatalytic performances
  16. Development of (−)-epigallocatechin-3-gallate-loaded folate receptor-targeted nanoparticles for prostate cancer treatment
  17. Enhancement of the mechanical properties of HDPE mineral nanocomposites by filler particles modulation of the matrix plastic/elastic behavior
  18. Effect of plasticizers on the properties of sugar palm nanocellulose/cinnamon essential oil reinforced starch bionanocomposite films
  19. Optimization of nano coating to reduce the thermal deformation of ball screws
  20. Preparation of efficient piezoelectric PVDF–HFP/Ni composite films by high electric field poling
  21. MHD dissipative Casson nanofluid liquid film flow due to an unsteady stretching sheet with radiation influence and slip velocity phenomenon
  22. Effects of nano-SiO2 modification on rubberised mortar and concrete with recycled coarse aggregates
  23. Mechanical and microscopic properties of fiber-reinforced coal gangue-based geopolymer concrete
  24. Effect of morphology and size on the thermodynamic stability of cerium oxide nanoparticles: Experiment and molecular dynamics calculation
  25. Mechanical performance of a CFRP composite reinforced via gelatin-CNTs: A study on fiber interfacial enhancement and matrix enhancement
  26. A practical review over surface modification, nanopatterns, emerging materials, drug delivery systems, and their biophysiochemical properties for dental implants: Recent progresses and advances
  27. HTR: An ultra-high speed algorithm for cage recognition of clathrate hydrates
  28. Effects of microalloying elements added by in situ synthesis on the microstructure of WCu composites
  29. A highly sensitive nanobiosensor based on aptamer-conjugated graphene-decorated rhodium nanoparticles for detection of HER2-positive circulating tumor cells
  30. Progressive collapse performance of shear strengthened RC frames by nano CFRP
  31. Core–shell heterostructured composites of carbon nanotubes and imine-linked hyperbranched polymers as metal-free Li-ion anodes
  32. A Galerkin strategy for tri-hybridized mixture in ethylene glycol comprising variable diffusion and thermal conductivity using non-Fourier’s theory
  33. Simple models for tensile modulus of shape memory polymer nanocomposites at ambient temperature
  34. Preparation and morphological studies of tin sulfide nanoparticles and use as efficient photocatalysts for the degradation of rhodamine B and phenol
  35. Polyethyleneimine-impregnated activated carbon nanofiber composited graphene-derived rice husk char for efficient post-combustion CO2 capture
  36. Electrospun nanofibers of Co3O4 nanocrystals encapsulated in cyclized-polyacrylonitrile for lithium storage
  37. Pitting corrosion induced on high-strength high carbon steel wire in high alkaline deaerated chloride electrolyte
  38. Formulation of polymeric nanoparticles loaded sorafenib; evaluation of cytotoxicity, molecular evaluation, and gene expression studies in lung and breast cancer cell lines
  39. Engineered nanocomposites in asphalt binders
  40. Influence of loading voltage, domain ratio, and additional load on the actuation of dielectric elastomer
  41. Thermally induced hex-graphene transitions in 2D carbon crystals
  42. The surface modification effect on the interfacial properties of glass fiber-reinforced epoxy: A molecular dynamics study
  43. Molecular dynamics study of deformation mechanism of interfacial microzone of Cu/Al2Cu/Al composites under tension
  44. Nanocolloid simulators of luminescent solar concentrator photovoltaic windows
  45. Compressive strength and anti-chloride ion penetration assessment of geopolymer mortar merging PVA fiber and nano-SiO2 using RBF–BP composite neural network
  46. Effect of 3-mercapto-1-propane sulfonate sulfonic acid and polyvinylpyrrolidone on the growth of cobalt pillar by electrodeposition
  47. Dynamics of convective slippery constraints on hybrid radiative Sutterby nanofluid flow by Galerkin finite element simulation
  48. Preparation of vanadium by the magnesiothermic self-propagating reduction and process control
  49. Microstructure-dependent photoelectrocatalytic activity of heterogeneous ZnO–ZnS nanosheets
  50. Cytotoxic and pro-inflammatory effects of molybdenum and tungsten disulphide on human bronchial cells
  51. Improving recycled aggregate concrete by compression casting and nano-silica
  52. Chemically reactive Maxwell nanoliquid flow by a stretching surface in the frames of Newtonian heating, nonlinear convection and radiative flux: Nanopolymer flow processing simulation
  53. Nonlinear dynamic and crack behaviors of carbon nanotubes-reinforced composites with various geometries
  54. Biosynthesis of copper oxide nanoparticles and its therapeutic efficacy against colon cancer
  55. Synthesis and characterization of smart stimuli-responsive herbal drug-encapsulated nanoniosome particles for efficient treatment of breast cancer
  56. Homotopic simulation for heat transport phenomenon of the Burgers nanofluids flow over a stretching cylinder with thermal convective and zero mass flux conditions
  57. Incorporation of copper and strontium ions in TiO2 nanotubes via dopamine to enhance hemocompatibility and cytocompatibility
  58. Mechanical, thermal, and barrier properties of starch films incorporated with chitosan nanoparticles
  59. Mechanical properties and microstructure of nano-strengthened recycled aggregate concrete
  60. Glucose-responsive nanogels efficiently maintain the stability and activity of therapeutic enzymes
  61. Tunning matrix rheology and mechanical performance of ultra-high performance concrete using cellulose nanofibers
  62. Flexible MXene/copper/cellulose nanofiber heat spreader films with enhanced thermal conductivity
  63. Promoted charge separation and specific surface area via interlacing of N-doped titanium dioxide nanotubes on carbon nitride nanosheets for photocatalytic degradation of Rhodamine B
  64. Elucidating the role of silicon dioxide and titanium dioxide nanoparticles in mitigating the disease of the eggplant caused by Phomopsis vexans, Ralstonia solanacearum, and root-knot nematode Meloidogyne incognita
  65. An implication of magnetic dipole in Carreau Yasuda liquid influenced by engine oil using ternary hybrid nanomaterial
  66. Robust synthesis of a composite phase of copper vanadium oxide with enhanced performance for durable aqueous Zn-ion batteries
  67. Tunning self-assembled phases of bovine serum albumin via hydrothermal process to synthesize novel functional hydrogel for skin protection against UVB
  68. A comparative experimental study on damping properties of epoxy nanocomposite beams reinforced with carbon nanotubes and graphene nanoplatelets
  69. Lightweight and hydrophobic Ni/GO/PVA composite aerogels for ultrahigh performance electromagnetic interference shielding
  70. Research on the auxetic behavior and mechanical properties of periodically rotating graphene nanostructures
  71. Repairing performances of novel cement mortar modified with graphene oxide and polyacrylate polymer
  72. Closed-loop recycling and fabrication of hydrophilic CNT films with high performance
  73. Design of thin-film configuration of SnO2–Ag2O composites for NO2 gas-sensing applications
  74. Study on stress distribution of SiC/Al composites based on microstructure models with microns and nanoparticles
  75. PVDF green nanofibers as potential carriers for improving self-healing and mechanical properties of carbon fiber/epoxy prepregs
  76. Osteogenesis capability of three-dimensionally printed poly(lactic acid)-halloysite nanotube scaffolds containing strontium ranelate
  77. Silver nanoparticles induce mitochondria-dependent apoptosis and late non-canonical autophagy in HT-29 colon cancer cells
  78. Preparation and bonding mechanisms of polymer/metal hybrid composite by nano molding technology
  79. Damage self-sensing and strain monitoring of glass-reinforced epoxy composite impregnated with graphene nanoplatelet and multiwalled carbon nanotubes
  80. Thermal analysis characterisation of solar-powered ship using Oldroyd hybrid nanofluids in parabolic trough solar collector: An optimal thermal application
  81. Pyrene-functionalized halloysite nanotubes for simultaneously detecting and separating Hg(ii) in aqueous media: A comprehensive comparison on interparticle and intraparticle excimers
  82. Fabrication of self-assembly CNT flexible film and its piezoresistive sensing behaviors
  83. Thermal valuation and entropy inspection of second-grade nanoscale fluid flow over a stretching surface by applying Koo–Kleinstreuer–Li relation
  84. Mechanical properties and microstructure of nano-SiO2 and basalt-fiber-reinforced recycled aggregate concrete
  85. Characterization and tribology performance of polyaniline-coated nanodiamond lubricant additives
  86. Combined impact of Marangoni convection and thermophoretic particle deposition on chemically reactive transport of nanofluid flow over a stretching surface
  87. Spark plasma extrusion of binder free hydroxyapatite powder
  88. An investigation on thermo-mechanical performance of graphene-oxide-reinforced shape memory polymer
  89. Effect of nanoadditives on the novel leather fiber/recycled poly(ethylene-vinyl-acetate) polymer composites for multifunctional applications: Fabrication, characterizations, and multiobjective optimization using central composite design
  90. Design selection for a hemispherical dimple core sandwich panel using hybrid multi-criteria decision-making methods
  91. Improving tensile strength and impact toughness of plasticized poly(lactic acid) biocomposites by incorporating nanofibrillated cellulose
  92. Green synthesis of spinel copper ferrite (CuFe2O4) nanoparticles and their toxicity
  93. The effect of TaC and NbC hybrid and mono-nanoparticles on AA2024 nanocomposites: Microstructure, strengthening, and artificial aging
  94. Excited-state geometry relaxation of pyrene-modified cellulose nanocrystals under UV-light excitation for detecting Fe3+
  95. Effect of CNTs and MEA on the creep of face-slab concrete at an early age
  96. Effect of deformation conditions on compression phase transformation of AZ31
  97. Application of MXene as a new generation of highly conductive coating materials for electromembrane-surrounded solid-phase microextraction
  98. A comparative study of the elasto-plastic properties for ceramic nanocomposites filled by graphene or graphene oxide nanoplates
  99. Encapsulation strategies for improving the biological behavior of CdS@ZIF-8 nanocomposites
  100. Biosynthesis of ZnO NPs from pumpkin seeds’ extract and elucidation of its anticancer potential against breast cancer
  101. Preliminary trials of the gold nanoparticles conjugated chrysin: An assessment of anti-oxidant, anti-microbial, and in vitro cytotoxic activities of a nanoformulated flavonoid
  102. Effect of micron-scale pores increased by nano-SiO2 sol modification on the strength of cement mortar
  103. Fractional simulations for thermal flow of hybrid nanofluid with aluminum oxide and titanium oxide nanoparticles with water and blood base fluids
  104. The effect of graphene nano-powder on the viscosity of water: An experimental study and artificial neural network modeling
  105. Development of a novel heat- and shear-resistant nano-silica gelling agent
  106. Characterization, biocompatibility and in vivo of nominal MnO2-containing wollastonite glass-ceramic
  107. Entropy production simulation of second-grade magnetic nanomaterials flowing across an expanding surface with viscidness dissipative flux
  108. Enhancement in structural, morphological, and optical properties of copper oxide for optoelectronic device applications
  109. Aptamer-functionalized chitosan-coated gold nanoparticle complex as a suitable targeted drug carrier for improved breast cancer treatment
  110. Performance and overall evaluation of nano-alumina-modified asphalt mixture
  111. Analysis of pure nanofluid (GO/engine oil) and hybrid nanofluid (GO–Fe3O4/engine oil): Novel thermal and magnetic features
  112. Synthesis of Ag@AgCl modified anatase/rutile/brookite mixed phase TiO2 and their photocatalytic property
  113. Mechanisms and influential variables on the abrasion resistance hydraulic concrete
  114. Synergistic reinforcement mechanism of basalt fiber/cellulose nanocrystals/polypropylene composites
  115. Achieving excellent oxidation resistance and mechanical properties of TiB2–B4C/carbon aerogel composites by quick-gelation and mechanical mixing
  116. Microwave-assisted sol–gel template-free synthesis and characterization of silica nanoparticles obtained from South African coal fly ash
  117. Pulsed laser-assisted synthesis of nano nickel(ii) oxide-anchored graphitic carbon nitride: Characterizations and their potential antibacterial/anti-biofilm applications
  118. Effects of nano-ZrSi2 on thermal stability of phenolic resin and thermal reusability of quartz–phenolic composites
  119. Benzaldehyde derivatives on tin electroplating as corrosion resistance for fabricating copper circuit
  120. Mechanical and heat transfer properties of 4D-printed shape memory graphene oxide/epoxy acrylate composites
  121. Coupling the vanadium-induced amorphous/crystalline NiFe2O4 with phosphide heterojunction toward active oxygen evolution reaction catalysts
  122. Graphene-oxide-reinforced cement composites mechanical and microstructural characteristics at elevated temperatures
  123. Gray correlation analysis of factors influencing compressive strength and durability of nano-SiO2 and PVA fiber reinforced geopolymer mortar
  124. Preparation of layered gradient Cu–Cr–Ti alloy with excellent mechanical properties, thermal stability, and electrical conductivity
  125. Recovery of Cr from chrome-containing leather wastes to develop aluminum-based composite material along with Al2O3 ceramic particles: An ingenious approach
  126. Mechanisms of the improved stiffness of flexible polymers under impact loading
  127. Anticancer potential of gold nanoparticles (AuNPs) using a battery of in vitro tests
  128. Review Articles
  129. Proposed approaches for coronaviruses elimination from wastewater: Membrane techniques and nanotechnology solutions
  130. Application of Pickering emulsion in oil drilling and production
  131. The contribution of microfluidics to the fight against tuberculosis
  132. Graphene-based biosensors for disease theranostics: Development, applications, and recent advancements
  133. Synthesis and encapsulation of iron oxide nanorods for application in magnetic hyperthermia and photothermal therapy
  134. Contemporary nano-architectured drugs and leads for ανβ3 integrin-based chemotherapy: Rationale and retrospect
  135. State-of-the-art review of fabrication, application, and mechanical properties of functionally graded porous nanocomposite materials
  136. Insights on magnetic spinel ferrites for targeted drug delivery and hyperthermia applications
  137. A review on heterogeneous oxidation of acetaminophen based on micro and nanoparticles catalyzed by different activators
  138. Early diagnosis of lung cancer using magnetic nanoparticles-integrated systems
  139. Advances in ZnO: Manipulation of defects for enhancing their technological potentials
  140. Efficacious nanomedicine track toward combating COVID-19
  141. A review of the design, processes, and properties of Mg-based composites
  142. Green synthesis of nanoparticles for varied applications: Green renewable resources and energy-efficient synthetic routes
  143. Two-dimensional nanomaterial-based polymer composites: Fundamentals and applications
  144. Recent progress and challenges in plasmonic nanomaterials
  145. Apoptotic cell-derived micro/nanosized extracellular vesicles in tissue regeneration
  146. Electronic noses based on metal oxide nanowires: A review
  147. Framework materials for supercapacitors
  148. An overview on the reproductive toxicity of graphene derivatives: Highlighting the importance
  149. Antibacterial nanomaterials: Upcoming hope to overcome antibiotic resistance crisis
  150. Research progress of carbon materials in the field of three-dimensional printing polymer nanocomposites
  151. A review of atomic layer deposition modelling and simulation methodologies: Density functional theory and molecular dynamics
  152. Recent advances in the preparation of PVDF-based piezoelectric materials
  153. Recent developments in tensile properties of friction welding of carbon fiber-reinforced composite: A review
  154. Comprehensive review of the properties of fly ash-based geopolymer with additive of nano-SiO2
  155. Perspectives in biopolymer/graphene-based composite application: Advances, challenges, and recommendations
  156. Graphene-based nanocomposite using new modeling molecular dynamic simulations for proposed neutralizing mechanism and real-time sensing of COVID-19
  157. Nanotechnology application on bamboo materials: A review
  158. Recent developments and future perspectives of biorenewable nanocomposites for advanced applications
  159. Nanostructured lipid carrier system: A compendium of their formulation development approaches, optimization strategies by quality by design, and recent applications in drug delivery
  160. 3D printing customized design of human bone tissue implant and its application
  161. Design, preparation, and functionalization of nanobiomaterials for enhanced efficacy in current and future biomedical applications
  162. A brief review of nanoparticles-doped PEDOT:PSS nanocomposite for OLED and OPV
  163. Nanotechnology interventions as a putative tool for the treatment of dental afflictions
  164. Recent advancements in metal–organic frameworks integrating quantum dots (QDs@MOF) and their potential applications
  165. A focused review of short electrospun nanofiber preparation techniques for composite reinforcement
  166. Microstructural characteristics and nano-modification of interfacial transition zone in concrete: A review
  167. Latest developments in the upconversion nanotechnology for the rapid detection of food safety: A review
  168. Strategic applications of nano-fertilizers for sustainable agriculture: Benefits and bottlenecks
  169. Molecular dynamics application of cocrystal energetic materials: A review
  170. Synthesis and application of nanometer hydroxyapatite in biomedicine
  171. Cutting-edge development in waste-recycled nanomaterials for energy storage and conversion applications
  172. Biological applications of ternary quantum dots: A review
  173. Nanotherapeutics for hydrogen sulfide-involved treatment: An emerging approach for cancer therapy
  174. Application of antibacterial nanoparticles in orthodontic materials
  175. Effect of natural-based biological hydrogels combined with growth factors on skin wound healing
  176. Nanozymes – A route to overcome microbial resistance: A viewpoint
  177. Recent developments and applications of smart nanoparticles in biomedicine
  178. Contemporary review on carbon nanotube (CNT) composites and their impact on multifarious applications
  179. Interfacial interactions and reinforcing mechanisms of cellulose and chitin nanomaterials and starch derivatives for cement and concrete strength and durability enhancement: A review
  180. Diamond-like carbon films for tribological modification of rubber
  181. Layered double hydroxides (LDHs) modified cement-based materials: A systematic review
  182. Recent research progress and advanced applications of silica/polymer nanocomposites
  183. Modeling of supramolecular biopolymers: Leading the in silico revolution of tissue engineering and nanomedicine
  184. Recent advances in perovskites-based optoelectronics
  185. Biogenic synthesis of palladium nanoparticles: New production methods and applications
  186. A comprehensive review of nanofluids with fractional derivatives: Modeling and application
  187. Electrospinning of marine polysaccharides: Processing and chemical aspects, challenges, and future prospects
  188. Electrohydrodynamic printing for demanding devices: A review of processing and applications
  189. Rapid Communications
  190. Structural material with designed thermal twist for a simple actuation
  191. Recent advances in photothermal materials for solar-driven crude oil adsorption
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 5.9.2025 from https://www.degruyterbrill.com/document/doi/10.1515/ntrev-2022-0091/html
Scroll to top button