Startseite Naturwissenschaften Oxidation Behavior of NiCr/YSZ Thermal Barrier Coatings (TBCs)
Artikel Open Access

Oxidation Behavior of NiCr/YSZ Thermal Barrier Coatings (TBCs)

  • Kadir Mert Doleker EMAIL logo , Yasin Ozgurluk , Abdullah Selim Parlakyigit , Dervis Ozkan , Turgut Gulmez und Abdullah Cahit Karaoglanli
Veröffentlicht/Copyright: 21. September 2018
Artikel downloaden (PDF)
Open Chemistry
Aus der Zeitschrift Open Chemistry Band 16 Heft 1

Abstract

Nichrome (NiCr) coatings are widely used to provide resistance against oxidation and corrosion in many machine components. TBCs must include bond coatings that are resistant to oxidation resulting fromhigh-temperature operating conditions. In the present study, NiCr powders were sprayed on nickel-based superalloy Inconel 718 substrates using atmospheric plasma spray (APS) technique. Bond-coated substrates were coated with yittria stabilized zirconia (YSZ). As such, the TBC samples were kept at 1000°C for 8 h, 24 h and 50 h in high temperature furnace and their isothermal oxidation behavior was investigated. Microstructure and phase change properties of TBCs before and after isothermal oxidation were then studied and analyzed.

Keywords: Thermal barrier coatings (TBCs); Oxidation; NiCr; Yittria stabilized zirconia (YSZ)
PACS: 81.15.Dj; 81.65.Mq; 81.15.Rs; 81.65.Kn

1 Introduction

High temperature materials like Ni-based superalloys can be oxidized if exposed to prolonged operations in high temperatures. Oxidation in such instances can lead to failures and serious consequences. Various metallic components complete their lifetime early. To protect metallic parts in high temperature applications, thermal barrier coatings (TBCs) are the preferred choice for use as protective coatitgs, as they are good thermal insulators. Bond coats are deposited on a substrate to obtain better adhesion and to decrease thermal expansion mismatch with a top coat. TBCs also provide oxidation and corrosion resistance. Generally, NiCr, NiAl, NiPt or MCrAlY are used as bond coat materials. Top layer consists of a ceramic material that has low thermal conductivity and high temperature resistance [1,2,3,4,5,6]. In the production of a bond coat, thermal spray techniques such as atmospheric plasma spray (APS) or high velocity oxygen fuel (HVOF) are often utilized, as they offer low cost and direct applicability. In an APS technique, powders can be sprayed on a substrate as molten or semi-molten materials. All materials can be deposited using this plasma technique. APS coatings have laminar structure, porosity and oxide containing microstructures [7,8,9]. NiCr and NiCr-based coatings are used to provide resistance against corrosion, oxidation or erosion [10,11]. They were widely adopted in exhaust nozzle of rockets as bond coat material. YSZ is the preferred top coat material in TBC systems [12,13,14]. YSZ has high coefficient of thermal expansion, high fracture toughness and low thermal conductivity compared to other ceramic materials, and it can be used in temperatures up to 1200°C [15,16].

In this study, Inconel 718 was used as substrate, NiCr was sprayed as a bond coat and YSZ was deposited as a top coat. Ni-based superalloys are typically subjected to 800-1100°C operating conditions thus produced TBCs were exposed to 1000°C in furnace at varying times. Oxidation behavior of TBCs with respect to time was evaluated.

2 Experimental Procedure

2.1 TBC Sample Production and Preparation

Inconel 718 with 25.4 mm diameter and 5 mm thickness was used as a substrate. Its chemical composition mainly consisted of Ni, Fe, Cr, Nb and Mo. Substrates were sandblasted before the bond coat production. NiCr (80/20) powders (firm: GTV, 80.20.1 code, particle: -53 +20 μm,) were sprayed on Inconel 718 using APS technique. In Figure 1, images of a) NiCr and b) YSZ powders are given with their XRD analyses, respectively. NiCr powders have a spherical shape and consist of γ-Ni and NiCr phases. Similarly, YSZ powders have spherical shape, yet they consist of only t-ZrO2.

Figure 1 a) NiCr powders and XRD analysis, b) YSZ powders and XRD analysis.
Figure 1

a) NiCr powders and XRD analysis, b) YSZ powders and XRD analysis.

After depositing the bond coat, YSZ (ZrO2+8%Y2O3) powders (firm: Sulzer Metco 204F, particle: −45 + 15 μm) were sprayed on NiCr bond-coated substrates. Spray parameters of bond and top coat are given in Table 1. According to Table 1, there are small differences between deposition parameters due to plasma atmosphere such as used gas flow rates (standard lit per minute (slpm)), spray distance (mm) or arc current (A).

Table 1

Spraying parameters of NiCr and YSZ.

CoatingArc currentH2 flow rateAr flow ratePowder feedstock rateSpray distance
NiCr500 A15 slpm80 slpm25 g/min.80 mm
YSZ630 A20 slpm90 slpm25 g/min.90 mm

2.2 Oxidation Tests and Characterization

Image J software program was used to calculate average porosity and oxide content as percentage, information obtained from 5 different cross-sectional SEM images at 1kx magnification. In lab atmosphere, oxidation tests were performed at 1000°C for 8 h, 24 h and 50 h, using PLF 130/12 Protherm high-temperature furnace. Crosssections of oxidized TBCs were analyzed using SEM (Tescan, Maia3). XRD (Rigaku, CuKα) analysis of TBCs was performed to determine material phases. Thermally grown oxide (TGO) values were calculated using Image Pro Plus 6 software program by taking average of 10 measurements from interfaces of 10 images at 3kx magnification for each oxidation periods.

Ethical approval: The conducted research is not related to either human or animals use.

3 Results and Discussion

SEM and elemental mapping microstructures of as-sprayed TBC are shown in Figure 2. Bond coats have porosity and show presence of oxides. Top coat has porosity the same as the bond coat, which is caused by the characteristic properties of APS technique. Average oxide and porosity content of as-sprayed 100 μm-NiCr coating were 5.91% and 1,59%, respectively while as-sprayed 300 μm-YSZ coating had 5.58% porosity according to Image analysis. Elemental distribution shows that there are locally oxidized regions consisting of mainly Cr2O3 phases.

Figure 2 As-deposited TBC SEM and elemental mapping microstructures.
Figure 2

As-deposited TBC SEM and elemental mapping microstructures.

YSZ has an ionic conductivity due to the its crystal structure. At high temperature, oxygen diffuses from top coat to bond coat with affecting both, YSZ structure and existing porosities [16,17]. Cr is more reactive compared to Ni according to Ellingham diagrams [18]. For this reason, Cr first reacts with oxygen forming protective Cr2O3 layer at the interface during this oxidation reaction. Cr2O3 layer acts as an oxygen barrier and that is why TGO layer mainly consists of Cr2O3 phase considering all oxidation periods [19,20].

In Figure 3, SEM microstructures of oxidized TBCs at 1000°C for 8 h, 24 h and 50 h are shown. TGO layer thickness increased with the increase of oxidation time. CrO3 phase can be volatilized at the temperature higher than 1000°C [l9,20,21]. However, volatilization of CrO3 was not detected with use of YSZ, as it provided thermal barrier and caused temperature drop.

Figure 3 SEM microstructures after a) as-sprayed, b) 8 h, c) 24 h and d) 50 h oxidation tests at 1000°C.
Figure 3

SEM microstructures after a) as-sprayed, b) 8 h, c) 24 h and d) 50 h oxidation tests at 1000°C.

At the end of oxidation periods, spallation was not observed, as evident from Figure 4. Top coat shows little densification, whereas bond coat layer shows localized oxidation. Based on elemental distributions, there was no evidence of presence of other oxides, such as NiO or NiCr2O4 which are undesired phases due to higher growth rate [22]. This shows that NiCr is a suitable bond coat material for TBCs at 1000°C applications.

Figure 4 SEM and elemental mapping image of TBC oxidized for 50 h at 1000°C.
Figure 4

SEM and elemental mapping image of TBC oxidized for 50 h at 1000°C.

Figure 5 shows XRD and TGO growth behavior of TBCs. According to XRD results, phase transformation on the top coat did not occur at the end of the oxidation and the top coat only consisted of tetragonal ZrO2 (t-ZrO2). Semi-tetragonal ZrO2 phase is durable at temperatures up to 1173°C, therefore, phase transformation has not occurred [23]. With increased time, TGO layer thickness increased and, with the highest increase observed in initial oxidation stage. Interestingly, TGO thickness exhibits similar growth but lower growth rate compared to CoNiCrAlY TBCs in literature [22,24] for isothermal oxidation tests at 1000°C.

Figure 5 XRD analysis of as-sprayed and 50 h oxidized TBC and, TGO growth behavior with respect to time.
Figure 5

XRD analysis of as-sprayed and 50 h oxidized TBC and, TGO growth behavior with respect to time.

However, internal oxidation rate can be higher in NiCr TBCs. Thus, results can change at higher dwell times.

4 Conclusion

Bond and top coat were successfully deposited on Inconel 718 substrate. TBCs exposed to oxidation experiments and other tested specimens withstood to oxidation periods. TGO layer consisting mainly of Cr2O3 layer preserved its uniformity. During the oxidation, YSZ did not experience phase transformation and did not result in crack formations. The thickness of TGO layer increased with an increased time. Normally, 1000°C temperature is not preferred with NiCr coating due to the volatilization of CrO3 phase. However, with the use of YSZ, a temperature drop has been achieved. As a result, the present study was able to demonstrate that a low cost NiCr bond coating combined with low cost APS technique can be used in 1000°C applications. In future studies, the effects of different production techniques on durability of high temperature NiCr TBCs will be investigated.

Acknowledgments

This investigation was financially supported by Scientific Research Projects (BAP) Coordinatorship of Karabuk University with project code of KBÜBAP-17-DR-202.

  1. Conflict of interest: Authors state no conflict of interest.

References

[1] Doleker K.M., Ahlatci H., Karaoglanli A.C., Investigation of Isothermal Oxidation Behavior of Thermal Barrier Coatings (TBCs) Consisting of YSZ and Multilayered YSZ/Gd2Zr2O7 Ceramic Layers, Oxid. Met., 2017, 88(1-2), 109-119.10.1007/s11085-016-9690-4Suche in Google Scholar

[2] Doleker K.M., Karaoglanli A.C., Comparison of oxidation behavior of YSZ and Gd2Zr2O7 thermal barrier coatings (TBCs). Surf. Coat. Tech., 2017, 318, 198-207.10.1016/j.surfcoat.2016.12.078Suche in Google Scholar

[3] Padture N.P., Gell M., Jordan E.H., Thermal barrier coatings for gas-turbine engine applications. Science, 2002, 296(5566), 280-284.10.1126/science.1068609Suche in Google Scholar

[4] Clarke D.R., Materials selection guidelines for low thermal conductivity thermal barrier coatings. Surf. Coat. Tech., 2003, 163, 67-74.10.1016/S0257-8972(02)00593-5Suche in Google Scholar

[5] Clarke D.R., Phillpot S.R., Thermal barrier coating materials. Mater. today, 2005, 8(6), 22-29.10.1016/S1369-7021(05)70934-2Suche in Google Scholar

[6] Zhu D., Miller R.A., Development of advanced low conductivity thermal barrier coatings. Int. J. Appl. Ceram. Tec., 2004, 1(1), 86-94.10.1111/j.1744-7402.2004.tb00158.xSuche in Google Scholar

[7] Karaoglanli A.C., Dikici H., Kucuk Y., Effects of heat treatment on adhesion strength of thermal barrier coating systems. Eng. Fail. Anal., 2013, 32, 16-22.10.1016/j.engfailanal.2013.02.029Suche in Google Scholar

[8] Liu S.H., Li C.X., Zhang H.Y., Zhang S.L., Li L., Xu P., Yang G.J., Li C.J., A novel structure of YSZ coatings by atmospheric laminar plasma spraying technology. Scripta Mater.,2018, 153, 73-76.10.1016/j.scriptamat.2018.04.022Suche in Google Scholar

[9] Richer P., Yandouzi M., Beauvais L., Jodoin B., Oxidation behaviour of CoNiCrAlY bond coats produced by plasma, HVOF and cold gas dynamic spraying. Surf. Coat. Tech., 2010, 204(24), 3962-3974.10.1016/j.surfcoat.2010.03.043Suche in Google Scholar

[10] Yamada K., Tomono Y., Morimoto J., Sasaki Y., Ohmori A., Hot corrosion behavior of boiler tube materials in refuse incineration environment. Vacuum, 2002, 65(3-4), 533-540.10.1016/S0042-207X(01)00468-7Suche in Google Scholar

[11] Espallargas N., Berget J., Guilemany J.M., Benedetti A.V., Suegama P.H., Cr3C2–NiCr and WC–Ni thermal spray coatings as alternatives to hard chromium for erosion–corrosion resistance. Surf. Coat. Tech., 2008, 202(8), 1405-1417.10.1016/j.surfcoat.2007.06.048Suche in Google Scholar

[12] Cao X.Q., Vassen R., Stoever D., Ceramic materials for thermal barrier coatings. J. Eur. Ceram. Soc., 2004, 24(1), 1-10.10.1016/S0955-2219(03)00129-8Suche in Google Scholar

[13] Ozgurluk Y., Doleker K.M., Karaoglanli A.C., Hot corrosion behavior of YSZ, Gd2Zr2O7 and YSZ/ Gd2Zr2O7 thermal barrier coatings exposed to molten sulfate and vanadate salt, Appl. Surf. Sci., (in press), 10.1016/j.apsusc.2017.09.047.Suche in Google Scholar

[14] Morks M.F., Berndt C.C., Corrosion and oxidation properties of NiCr coatings sprayed in presence of gas shroud system. Appl. Surf.Sci., 2010, 256(13), 4322-4327.10.1016/j.apsusc.2010.02.024Suche in Google Scholar

[15] Vaßen R., Jarligo M.O., Steinke T., Mack D.E., Stöver D., Overview on advanced thermal barrier coatings. Surf. Coat. Tech., 2010, 205(4), 938-942.10.1016/j.surfcoat.2010.08.151Suche in Google Scholar

[16] Ma K., Schoenung J.M., Isothermal oxidation behavior of cryomilled NiCrAlY bond coat: homogeneity and growth rate of TGO. Surf. Coat. Tech., 2011, 205(21-22), 5178-5185.10.1016/j.surfcoat.2011.05.025Suche in Google Scholar

[17] Chen Y., Reed R.C., Marquis E.A., As-coated thermal barrier coating: structure and chemistry. Scripta Mater., 2012, 67(9), 779-782.10.1016/j.scriptamat.2012.06.023Suche in Google Scholar

[18] Gaskell D.R., Laughlin D.E., Introduction to the Thermodynamics of Materials, 5rd ed., Taylor & Francis Group, New York, 2017.Suche in Google Scholar

[19] Berthod P., Kinetics of high temperature oxidation and chromia volatilization for a binary Ni–Cr alloy, Oxid. Met., 2005, 64(3), 235-252.10.1007/s11085-005-6562-8Suche in Google Scholar

[20] Tsai S.C., Huntz A.M., Dolin C., Growth mechanism of Cr2O3 scales: oxygen and chromium diffusion, oxidation kinetics and effect of yttrium, Materials Science and Engineering: A, 1996, 212(1), 6-13.10.1016/0921-5093(96)10173-8Suche in Google Scholar

[21] Sidhu T.S., Prakash S., Agrawal R.D. Studies on the properties of high-velocity oxy-fuel thermal spray coatings for higher temperature applications. Materials Science, 2005, 41(6), 805-823.10.1007/s11003-006-0047-zSuche in Google Scholar

[22] Nath S., Manna I., Majumdar J.D., Kinetics and mechanism of isothermal oxidation of compositionally graded yttria stabilized zirconia (YSZ) based thermal barrier coating, Corr. Sci., 2014, 88, 10-22.10.1016/j.corsci.2014.06.050Suche in Google Scholar

[23] Krogstad J.A., Krämer S., Lipkin D.M., Johnson C.A., Mitchell D.R.G., Cairney J.M., Levi C.G., Phase stability of t′-zirconia-based thermal barrier coatings: Mechanistic insights. J. American Ceram. Soc. 2011, 94(S1), 168–177.10.1111/j.1551-2916.2011.04531.xSuche in Google Scholar

[24] Karaoglanli A.C., Doleker K.M., Demirel B., Turk A., Varol R., Effect of shot peening on the oxidation behavior of thermal barrier coatings, Appl. Surf. Sci. 2015, 354, 314-322.10.1016/j.apsusc.2015.06.113Suche in Google Scholar

Received: 2018-01-31
Accepted: 2018-03-11
Published Online: 2018-09-21

© 2018 Kadir Mert Doleker et al., published by De Gruyter

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.

Artikel in diesem Heft

  1. Regular Articles
  2. The effect of CuO modification for a TiO2 nanotube confined CeO2 catalyst on the catalytic combustion of butane
  3. The preparation and antibacterial activity of cellulose/ZnO composite: a review
  4. Linde Type A and nano magnetite/NaA zeolites: cytotoxicity and doxorubicin loading efficiency
  5. Performance and thermal decomposition analysis of foaming agent NPL-10 for use in heavy oil recovery by steam injection
  6. Spectroscopic (FT-IR, FT-Raman, UV, 1H and 13C NMR) insights, electronic profiling and DFT computations on ({(E)-[3-(1H-imidazol-1-yl)-1-phenylpropylidene] amino}oxy)(4-nitrophenyl)methanone, an imidazole-bearing anti-Candida agent
  7. A Simplistic Preliminary Assessment of Ginstling-Brounstein Model for Solid Spherical Particles in the Context of a Diffusion-Controlled Synthesis
  8. M-Polynomials And Topological Indices Of Zigzag And Rhombic Benzenoid Systems
  9. Photochemical Transformation of some 3-benzyloxy-2-(benzo[b]thiophen-2-yl)-4Hchromen-4-ones: A Remote Substituent Effect
  10. Dynamic Changes of Secondary Metabolites and Antioxidant Activity of Ligustrum lucidum During Fruit Growth
  11. Studies on the flammability of polypropylene/ammonium polyphosphate and montmorillonite by using the cone calorimeter test
  12. DSC, FT-IR, NIR, NIR-PCA and NIR-ANOVA for determination of chemical stability of diuretic drugs: impact of excipients
  13. Antioxidant and Hepatoprotective Effects of Methanolic Extracts of Zilla spinosa and Hammada elegans Against Carbon Tetrachlorideinduced Hepatotoxicity in Rats
  14. Prunus cerasifera Ehrh. fabricated ZnO nano falcates and its photocatalytic and dose dependent in vitro bio-activity
  15. Organic biocides hosted in layered double hydroxides: enhancing antimicrobial activity
  16. Experimental study on the regulation of the cholinergic pathway in renal macrophages by microRNA-132 to alleviate inflammatory response
  17. Synthesis, characterization, in-vitro antimicrobial properties, molecular docking and DFT studies of 3-{(E)-[(4,6-dimethylpyrimidin-2-yl)imino]methyl} naphthalen-2-ol and Heteroleptic Mn(II), Co(II), Ni(II) and Zn(II) complexes
  18. M-Polynomials and Topological Indices of Dominating David Derived Networks
  19. Human Health Risk Assessment of Trace Metals in Surface Water Due to Leachate from the Municipal Dumpsite by Pollution Index: A Case Study from Ndawuse River, Abuja, Nigeria
  20. Analysis of Bowel Diseases from Blood Serum by Autofluorescence and Atomic Force Microscopy Techniques
  21. Hydrographic parameters and distribution of dissolved Cu, Ni, Zn and nutrients near Jeddah desalination plant
  22. Relationships between diatoms and environmental variables in industrial water biotopes of Trzuskawica S.A. (Poland)
  23. Optimum Conversion of Major Ginsenoside Rb1 to Minor Ginsenoside Rg3(S) by Pulsed Electric Field-Assisted Acid Hydrolysis Treatment
  24. Antioxidant, Anti-microbial Properties and Chemical Composition of Cumin Essential Oils Extracted by Three Methods
  25. Regulatory mechanism of ulinastatin on autophagy of macrophages and renal tubular epithelial cells
  26. Investigation of the sustained-release mechanism of hydroxypropyl methyl cellulose skeleton type Acipimox tablets
  27. Bio-accumulation of Polycyclic Aromatic Hydrocarbons in the Grey Mangrove (Avicennia marina) along Arabian Gulf, Saudi Coast
  28. Dynamic Change of Secondary Metabolites and spectrum-effect relationship of Malus halliana Koehne flowers during blooming
  29. Lipids constituents from Gardenia aqualla Stapf & Hutch
  30. Effect of using microwaves for catalysts preparation on the catalytic acetalization of glycerol with furfural to obtain fuel additives
  31. Effect of Humic Acid on the Degradation of Methylene Blue by Peroxymonosulfate
  32. Serum containing drugs of Gua Lou Xie Bai decoction (GLXB-D) can inhibit TGF-β1-Induced Epithelial to Mesenchymal Transition (EMT) in A549 Cells
  33. Antiulcer Activity of Different Extracts of Anvillea garcinii and Isolation of Two New Secondary Metabolites
  34. Analysis of Metabolites in Cabernet Sauvignon and Shiraz Dry Red Wines from Shanxi by 1H NMR Spectroscopy Combined with Pattern Recognition Analysis
  35. Can water temperature impact litter decomposition under pollution of copper and zinc mixture
  36. Released from ZrO2/SiO2 coating resveratrol inhibits senescence and oxidative stress of human adipose-derived stem cells (ASC)
  37. Validated thin-layer chromatographic method for alternative and simultaneous determination of two anti-gout agents in their fixed dose combinations
  38. Fast removal of pollutants from vehicle emissions during cold-start stage
  39. Review Article
  40. Catalytic activities of heterogeneous catalysts obtained by copolymerization of metal-containing 2-(acetoacetoxy)ethyl methacrylate
  41. Antibiotic Residue in the Aquatic Environment: Status in Africa
  42. Regular Articles
  43. Mercury fractionation in gypsum using temperature desorption and mass spectrometric detection
  44. Phytosynthetic Ag doped ZnO nanoparticles: Semiconducting green remediators
  45. Epithelial–Mesenchymal Transition Induced by SMAD4 Activation in Invasive Growth Hormone-Secreting Adenomas
  46. Physicochemical properties of stabilized sewage sludge admixtures by modified steel slag
  47. In Vitro Cytotoxic and Antiproliferative Activity of Cydonia oblonga flower petals, leaf and fruit pellet ethanolic extracts. Docking simulation of the active flavonoids on anti-apoptotic protein Bcl-2
  48. Synthesis and Characterization of Pd exchanged MMT Clay for Mizoroki-Heck Reaction
  49. A new selective, and sensitive method for the determination of lixivaptan, a vasopressin 2 (V2)-receptor antagonist, in mouse plasma and its application in a pharmacokinetic study
  50. Anti-EGFL7 antibodies inhibit rat prolactinoma MMQ cells proliferation and PRL secretion
  51. Density functional theory calculations, vibration spectral analysis and molecular docking of the antimicrobial agent 6-(1,3-benzodioxol-5-ylmethyl)-5-ethyl-2-{[2-(morpholin-4-yl)ethyl] sulfanyl}pyrimidin-4(3H)-one
  52. Effect of Nano Zeolite on the Transformation of Cadmium Speciation and Its Uptake by Tobacco in Cadmium-contaminated Soil
  53. Effects and Mechanisms of Jinniu Capsule on Methamphetamine-Induced Conditioned Place Preference in Rats
  54. Calculating the Degree-based Topological Indices of Dendrimers
  55. Efficient optimization and mineralization of UV absorbers: A comparative investigation with Fenton and UV/H2O2
  56. Metabolites of Tryptophane and Phenylalanine as Markers of Small Bowel Ischemia-Reperfusion Injury
  57. Adsorption and determination of polycyclic aromatic hydrocarbons in water through the aggregation of graphene oxide
  58. The role of NR2C2 in the prolactinomas
  59. Chromium removal from industrial wastewater using Phyllostachys pubescens biomass loaded Cu-S nanospheres
  60. Hydrotalcite Anchored Ruthenium Catalyst for CO2 Hydrogenation Reaction
  61. Preparation of Calcium Fluoride using Phosphogypsum by Orthogonal Experiment
  62. The mechanism of antibacterial activity of corylifolinin against three clinical bacteria from Psoralen corylifolia L
  63. 2-formyl-3,6-bis(hydroxymethyl)phenyl benzoate in Electrochemical Dry Cell
  64. Electro-photocatalytic degradation of amoxicillin using calcium titanate
  65. Effect of Malus halliana Koehne Polysaccharides on Functional Constipation
  66. Structural Properties and Nonlinear Optical Responses of Halogenated Compounds: A DFT Investigation on Molecular Modelling
  67. DMFDMA catalyzed synthesis of 2-((Dimethylamino)methylene)-3,4-dihydro-9-arylacridin-1(2H)-ones and their derivatives: in-vitro antifungal, antibacterial and antioxidant evaluations
  68. Production of Methanol as a Fuel Energy from CO2 Present in Polluted Seawater - A Photocatalytic Outlook
  69. Study of different extraction methods on finger print and fatty acid of raw beef fat using fourier transform infrared and gas chromatography-mass spectrometry
  70. Determination of trace fluoroquinolones in water solutions and in medicinal preparations by conventional and synchronous fluorescence spectrometry
  71. Extraction and determination of flavonoids in Carthamus tinctorius
  72. Therapeutic Application of Zinc and Vanadium Complexes against Diabetes Mellitus a Coronary Disease: A review
  73. Study of calcined eggshell as potential catalyst for biodiesel formation using used cooking oil
  74. Manganese oxalates - structure-based Insights
  75. Topological Indices of H-Naphtalenic Nanosheet
  76. Long-Term Dissolution of Glass Fibers in Water Described by Dissolving Cylinder Zero-Order Kinetic Model: Mass Loss and Radius Reduction
  77. Topological study of the para-line graphs of certain pentacene via topological indices
  78. A brief insight into the prediction of water vapor transmissibility in highly impermeable hybrid nanocomposites based on bromobutyl/epichlorohydrin rubber blends
  79. Comparative sulfite assay by voltammetry using Pt electrodes, photometry and titrimetry: Application to cider, vinegar and sugar analysis
  80. MicroRNA delivery mediated by PEGylated polyethylenimine for prostate cancer therapy
  81. Reversible Fluorescent Turn-on Sensors for Fe3+ based on a Receptor Composed of Tri-oxygen Atoms of Amide Groups in Water
  82. Sonocatalytic degradation of methyl orange in aqueous solution using Fe-doped TiO2 nanoparticles under mechanical agitation
  83. Hydrotalcite Anchored Ruthenium Catalyst for CO2 Hydrogenation Reaction
  84. Production and Analysis of Recycled Ammonium Perrhenate from CMSX-4 superalloys
  85. Topical Issue on Agriculture
  86. New phosphorus biofertilizers from renewable raw materials in the aspect of cadmium and lead contents in soil and plants
  87. Survey of content of cadmium, calcium, chromium, copper, iron, lead, magnesium, manganese, mercury, sodium and zinc in chamomile and green tea leaves by electrothermal or flame atomizer atomic absorption spectrometry
  88. Biogas digestate – benefits and risks for soil fertility and crop quality – an evaluation of grain maize response
  89. A numerical analysis of heat transfer in a cross-current heat exchanger with controlled and newly designed air flows
  90. Freshwater green macroalgae as a biosorbent of Cr(III) ions
  91. The main influencing factors of soil mechanical characteristics of the gravity erosion environment in the dry-hot valley of Jinsha river
  92. Free amino acids in Viola tricolor in relation to different habitat conditions
  93. The influence of filler amount on selected properties of new experimental resin dental composite
  94. Effect of poultry wastewater irrigation on nitrogen, phosphorus and carbon contents in farmland soil
  95. Response of spring wheat to NPK and S fertilization. The content and uptake of macronutrients and the value of ionic ratios
  96. The Effect of Macroalgal Extracts and Near Infrared Radiation on Germination of Soybean Seedlings: Preliminary Research Results
  97. Content of Zn, Cd and Pb in purple moor-grass in soils heavily contaminated with heavy metals around a zinc and lead ore tailing landfill
  98. Topical Issue on Research for Natural Bioactive Products
  99. Synthesis of (±)-3,4-dimethoxybenzyl-4-methyloctanoate as a novel internal standard for capsinoid determination by HPLC-ESI-MS/MS(QTOF)
  100. Repellent activity of monoterpenoid esters with neurotransmitter amino acids against yellow fever mosquito, Aedes aegypti
  101. Effect of Flammulina velutipes (golden needle mushroom, eno-kitake) polysaccharides on constipation
  102. Bioassay-directed fractionation of a blood coagulation factor Xa inhibitor, betulinic acid from Lycopus lucidus
  103. Antifungal and repellent activities of the essential oils from three aromatic herbs from western Himalaya
  104. Chemical composition and microbiological evaluation of essential oil from Hyssopus officinalis L. with white and pink flowers
  105. Bioassay-guided isolation and identification of Aedes aegypti larvicidal and biting deterrent compounds from Veratrum lobelianum
  106. α-Terpineol, a natural monoterpene: A review of its biological properties
  107. Utility of essential oils for development of host-based lures for Xyleborus glabratus (Coleoptera: Curculionidae: Scolytinae), vector of laurel wilt
  108. Phenolic composition and antioxidant potential of different organs of Kazakh Crataegus almaatensis Pojark: A comparison with the European Crataegus oxyacantha L. flowers
  109. Isolation of eudesmane type sesquiterpene ketone from Prangos heyniae H.Duman & M.F.Watson essential oil and mosquitocidal activity of the essential oils
  110. Comparative analysis of the polyphenols profiles and the antioxidant and cytotoxicity properties of various blue honeysuckle varieties
  111. Special Issue on ICCESEN 2017
  112. Modelling world energy security data from multinomial distribution by generalized linear model under different cumulative link functions
  113. Pine Cone and Boron Compounds Effect as Reinforcement on Mechanical and Flammability Properties of Polyester Composites
  114. Artificial Neural Network Modelling for Prediction of SNR Effected by Probe Properties on Ultrasonic Inspection of Austenitic Stainless Steel Weldments
  115. Calculation and 3D analyses of ERR in the band crack front contained in a rectangular plate made of multilayered material
  116. Improvement of fuel properties of biodiesel with bioadditive ethyl levulinate
  117. Properties of AlSi9Cu3 metal matrix micro and nano composites produced via stir casting
  118. Investigation of Antibacterial Properties of Ag Doped TiO2 Nanofibers Prepared by Electrospinning Process
  119. Modeling of Total Phenolic contents in Various Tea samples by Experimental Design Methods
  120. Nickel doping effect on the structural and optical properties of indium sulfide thin films by SILAR
  121. The effect mechanism of Ginnalin A as a homeopathic agent on various cancer cell lines
  122. Excitation functions of proton induced reactions of some radioisotopes used in medicine
  123. Oxide ionic conductivity and microstructures of Pr and Sm co-doped CeO2-based systems
  124. Rapid Synthesis of Metallic Reinforced in Situ Intermetallic Composites in Ti-Al-Nb System via Resistive Sintering
  125. Oxidation Behavior of NiCr/YSZ Thermal Barrier Coatings (TBCs)
  126. Clustering Analysis of Normal Strength Concretes Produced with Different Aggregate Types
  127. Magnetic Nano-Sized Solid Acid Catalyst Bearing Sulfonic Acid Groups for Biodiesel Synthesis
  128. The biological activities of Arabis alpina L. subsp. brevifolia (DC.) Cullen against food pathogens
  129. Humidity properties of Schiff base polymers
  130. Free Vibration Analysis of Fiber Metal Laminated Straight Beam
  131. Comparative study of in vitro antioxidant, acetylcholinesterase and butyrylcholinesterase activity of alfalfa (Medicago sativa L.) collected during different growth stages
  132. Isothermal Oxidation Behavior of Gadolinium Zirconate (Gd2Zr2O7) Thermal Barrier Coatings (TBCs) produced by Electron Beam Physical Vapor Deposition (EB-PVD) technique
  133. Optimization of Adsorption Parameters for Ultra-Fine Calcite Using a Box-Behnken Experimental Design
  134. The Microstructural Investigation of Vermiculite-Infiltrated Electron Beam Physical Vapor Deposition Thermal Barrier Coatings
  135. Modelling Porosity Permeability of Ceramic Tiles using Fuzzy Taguchi Method
  136. Experimental and theoretical study of a novel naphthoquinone Schiff base
  137. Physicochemical properties of heat treated sille stone for ceramic industry
  138. Sand Dune Characterization for Preparing Metallurgical Grade Silicon
  139. Catalytic Applications of Large Pore Sulfonic Acid-Functionalized SBA-15 Mesoporous Silica for Esterification
  140. One-photon Absorption Characterizations, Dipole Polarizabilities and Second Hyperpolarizabilities of Chlorophyll a and Crocin
  141. The Optical and Crystallite Characterization of Bilayer TiO2 Films Coated on Different ITO layers
  142. Topical Issue on Bond Activation
  143. Metal-mediated reactions towards the synthesis of a novel deaminolysed bisurea, dicarbamolyamine
  144. The structure of ortho-(trifluoromethyl)phenol in comparison to its homologues – A combined experimental and theoretical study
  145. Heterogeneous catalysis with encapsulated haem and other synthetic porphyrins: Harnessing the power of porphyrins for oxidation reactions
  146. Recent Advances on Mechanistic Studies on C–H Activation Catalyzed by Base Metals
  147. Reactions of the organoplatinum complex [Pt(cod) (neoSi)Cl] (neoSi = trimethylsilylmethyl) with the non-coordinating anions SbF6– and BPh4–
  148. Erratum
  149. Investigation on Two Compounds of O, O’-dithiophosphate Derivatives as Corrosion Inhibitors for Q235 Steel in Hydrochloric Acid Solution
https://doi.org/10.1515/chem-2018-0096
Schlagwörter für diesen Artikel
Thermal barrier coatings (TBCs); Oxidation; NiCr; Yittria stabilized zirconia (YSZ)
Creative Commons
BY-NC-ND 4.0

Artikel in diesem Heft

  1. Regular Articles
  2. The effect of CuO modification for a TiO2 nanotube confined CeO2 catalyst on the catalytic combustion of butane
  3. The preparation and antibacterial activity of cellulose/ZnO composite: a review
  4. Linde Type A and nano magnetite/NaA zeolites: cytotoxicity and doxorubicin loading efficiency
  5. Performance and thermal decomposition analysis of foaming agent NPL-10 for use in heavy oil recovery by steam injection
  6. Spectroscopic (FT-IR, FT-Raman, UV, 1H and 13C NMR) insights, electronic profiling and DFT computations on ({(E)-[3-(1H-imidazol-1-yl)-1-phenylpropylidene] amino}oxy)(4-nitrophenyl)methanone, an imidazole-bearing anti-Candida agent
  7. A Simplistic Preliminary Assessment of Ginstling-Brounstein Model for Solid Spherical Particles in the Context of a Diffusion-Controlled Synthesis
  8. M-Polynomials And Topological Indices Of Zigzag And Rhombic Benzenoid Systems
  9. Photochemical Transformation of some 3-benzyloxy-2-(benzo[b]thiophen-2-yl)-4Hchromen-4-ones: A Remote Substituent Effect
  10. Dynamic Changes of Secondary Metabolites and Antioxidant Activity of Ligustrum lucidum During Fruit Growth
  11. Studies on the flammability of polypropylene/ammonium polyphosphate and montmorillonite by using the cone calorimeter test
  12. DSC, FT-IR, NIR, NIR-PCA and NIR-ANOVA for determination of chemical stability of diuretic drugs: impact of excipients
  13. Antioxidant and Hepatoprotective Effects of Methanolic Extracts of Zilla spinosa and Hammada elegans Against Carbon Tetrachlorideinduced Hepatotoxicity in Rats
  14. Prunus cerasifera Ehrh. fabricated ZnO nano falcates and its photocatalytic and dose dependent in vitro bio-activity
  15. Organic biocides hosted in layered double hydroxides: enhancing antimicrobial activity
  16. Experimental study on the regulation of the cholinergic pathway in renal macrophages by microRNA-132 to alleviate inflammatory response
  17. Synthesis, characterization, in-vitro antimicrobial properties, molecular docking and DFT studies of 3-{(E)-[(4,6-dimethylpyrimidin-2-yl)imino]methyl} naphthalen-2-ol and Heteroleptic Mn(II), Co(II), Ni(II) and Zn(II) complexes
  18. M-Polynomials and Topological Indices of Dominating David Derived Networks
  19. Human Health Risk Assessment of Trace Metals in Surface Water Due to Leachate from the Municipal Dumpsite by Pollution Index: A Case Study from Ndawuse River, Abuja, Nigeria
  20. Analysis of Bowel Diseases from Blood Serum by Autofluorescence and Atomic Force Microscopy Techniques
  21. Hydrographic parameters and distribution of dissolved Cu, Ni, Zn and nutrients near Jeddah desalination plant
  22. Relationships between diatoms and environmental variables in industrial water biotopes of Trzuskawica S.A. (Poland)
  23. Optimum Conversion of Major Ginsenoside Rb1 to Minor Ginsenoside Rg3(S) by Pulsed Electric Field-Assisted Acid Hydrolysis Treatment
  24. Antioxidant, Anti-microbial Properties and Chemical Composition of Cumin Essential Oils Extracted by Three Methods
  25. Regulatory mechanism of ulinastatin on autophagy of macrophages and renal tubular epithelial cells
  26. Investigation of the sustained-release mechanism of hydroxypropyl methyl cellulose skeleton type Acipimox tablets
  27. Bio-accumulation of Polycyclic Aromatic Hydrocarbons in the Grey Mangrove (Avicennia marina) along Arabian Gulf, Saudi Coast
  28. Dynamic Change of Secondary Metabolites and spectrum-effect relationship of Malus halliana Koehne flowers during blooming
  29. Lipids constituents from Gardenia aqualla Stapf & Hutch
  30. Effect of using microwaves for catalysts preparation on the catalytic acetalization of glycerol with furfural to obtain fuel additives
  31. Effect of Humic Acid on the Degradation of Methylene Blue by Peroxymonosulfate
  32. Serum containing drugs of Gua Lou Xie Bai decoction (GLXB-D) can inhibit TGF-β1-Induced Epithelial to Mesenchymal Transition (EMT) in A549 Cells
  33. Antiulcer Activity of Different Extracts of Anvillea garcinii and Isolation of Two New Secondary Metabolites
  34. Analysis of Metabolites in Cabernet Sauvignon and Shiraz Dry Red Wines from Shanxi by 1H NMR Spectroscopy Combined with Pattern Recognition Analysis
  35. Can water temperature impact litter decomposition under pollution of copper and zinc mixture
  36. Released from ZrO2/SiO2 coating resveratrol inhibits senescence and oxidative stress of human adipose-derived stem cells (ASC)
  37. Validated thin-layer chromatographic method for alternative and simultaneous determination of two anti-gout agents in their fixed dose combinations
  38. Fast removal of pollutants from vehicle emissions during cold-start stage
  39. Review Article
  40. Catalytic activities of heterogeneous catalysts obtained by copolymerization of metal-containing 2-(acetoacetoxy)ethyl methacrylate
  41. Antibiotic Residue in the Aquatic Environment: Status in Africa
  42. Regular Articles
  43. Mercury fractionation in gypsum using temperature desorption and mass spectrometric detection
  44. Phytosynthetic Ag doped ZnO nanoparticles: Semiconducting green remediators
  45. Epithelial–Mesenchymal Transition Induced by SMAD4 Activation in Invasive Growth Hormone-Secreting Adenomas
  46. Physicochemical properties of stabilized sewage sludge admixtures by modified steel slag
  47. In Vitro Cytotoxic and Antiproliferative Activity of Cydonia oblonga flower petals, leaf and fruit pellet ethanolic extracts. Docking simulation of the active flavonoids on anti-apoptotic protein Bcl-2
  48. Synthesis and Characterization of Pd exchanged MMT Clay for Mizoroki-Heck Reaction
  49. A new selective, and sensitive method for the determination of lixivaptan, a vasopressin 2 (V2)-receptor antagonist, in mouse plasma and its application in a pharmacokinetic study
  50. Anti-EGFL7 antibodies inhibit rat prolactinoma MMQ cells proliferation and PRL secretion
  51. Density functional theory calculations, vibration spectral analysis and molecular docking of the antimicrobial agent 6-(1,3-benzodioxol-5-ylmethyl)-5-ethyl-2-{[2-(morpholin-4-yl)ethyl] sulfanyl}pyrimidin-4(3H)-one
  52. Effect of Nano Zeolite on the Transformation of Cadmium Speciation and Its Uptake by Tobacco in Cadmium-contaminated Soil
  53. Effects and Mechanisms of Jinniu Capsule on Methamphetamine-Induced Conditioned Place Preference in Rats
  54. Calculating the Degree-based Topological Indices of Dendrimers
  55. Efficient optimization and mineralization of UV absorbers: A comparative investigation with Fenton and UV/H2O2
  56. Metabolites of Tryptophane and Phenylalanine as Markers of Small Bowel Ischemia-Reperfusion Injury
  57. Adsorption and determination of polycyclic aromatic hydrocarbons in water through the aggregation of graphene oxide
  58. The role of NR2C2 in the prolactinomas
  59. Chromium removal from industrial wastewater using Phyllostachys pubescens biomass loaded Cu-S nanospheres
  60. Hydrotalcite Anchored Ruthenium Catalyst for CO2 Hydrogenation Reaction
  61. Preparation of Calcium Fluoride using Phosphogypsum by Orthogonal Experiment
  62. The mechanism of antibacterial activity of corylifolinin against three clinical bacteria from Psoralen corylifolia L
  63. 2-formyl-3,6-bis(hydroxymethyl)phenyl benzoate in Electrochemical Dry Cell
  64. Electro-photocatalytic degradation of amoxicillin using calcium titanate
  65. Effect of Malus halliana Koehne Polysaccharides on Functional Constipation
  66. Structural Properties and Nonlinear Optical Responses of Halogenated Compounds: A DFT Investigation on Molecular Modelling
  67. DMFDMA catalyzed synthesis of 2-((Dimethylamino)methylene)-3,4-dihydro-9-arylacridin-1(2H)-ones and their derivatives: in-vitro antifungal, antibacterial and antioxidant evaluations
  68. Production of Methanol as a Fuel Energy from CO2 Present in Polluted Seawater - A Photocatalytic Outlook
  69. Study of different extraction methods on finger print and fatty acid of raw beef fat using fourier transform infrared and gas chromatography-mass spectrometry
  70. Determination of trace fluoroquinolones in water solutions and in medicinal preparations by conventional and synchronous fluorescence spectrometry
  71. Extraction and determination of flavonoids in Carthamus tinctorius
  72. Therapeutic Application of Zinc and Vanadium Complexes against Diabetes Mellitus a Coronary Disease: A review
  73. Study of calcined eggshell as potential catalyst for biodiesel formation using used cooking oil
  74. Manganese oxalates - structure-based Insights
  75. Topological Indices of H-Naphtalenic Nanosheet
  76. Long-Term Dissolution of Glass Fibers in Water Described by Dissolving Cylinder Zero-Order Kinetic Model: Mass Loss and Radius Reduction
  77. Topological study of the para-line graphs of certain pentacene via topological indices
  78. A brief insight into the prediction of water vapor transmissibility in highly impermeable hybrid nanocomposites based on bromobutyl/epichlorohydrin rubber blends
  79. Comparative sulfite assay by voltammetry using Pt electrodes, photometry and titrimetry: Application to cider, vinegar and sugar analysis
  80. MicroRNA delivery mediated by PEGylated polyethylenimine for prostate cancer therapy
  81. Reversible Fluorescent Turn-on Sensors for Fe3+ based on a Receptor Composed of Tri-oxygen Atoms of Amide Groups in Water
  82. Sonocatalytic degradation of methyl orange in aqueous solution using Fe-doped TiO2 nanoparticles under mechanical agitation
  83. Hydrotalcite Anchored Ruthenium Catalyst for CO2 Hydrogenation Reaction
  84. Production and Analysis of Recycled Ammonium Perrhenate from CMSX-4 superalloys
  85. Topical Issue on Agriculture
  86. New phosphorus biofertilizers from renewable raw materials in the aspect of cadmium and lead contents in soil and plants
  87. Survey of content of cadmium, calcium, chromium, copper, iron, lead, magnesium, manganese, mercury, sodium and zinc in chamomile and green tea leaves by electrothermal or flame atomizer atomic absorption spectrometry
  88. Biogas digestate – benefits and risks for soil fertility and crop quality – an evaluation of grain maize response
  89. A numerical analysis of heat transfer in a cross-current heat exchanger with controlled and newly designed air flows
  90. Freshwater green macroalgae as a biosorbent of Cr(III) ions
  91. The main influencing factors of soil mechanical characteristics of the gravity erosion environment in the dry-hot valley of Jinsha river
  92. Free amino acids in Viola tricolor in relation to different habitat conditions
  93. The influence of filler amount on selected properties of new experimental resin dental composite
  94. Effect of poultry wastewater irrigation on nitrogen, phosphorus and carbon contents in farmland soil
  95. Response of spring wheat to NPK and S fertilization. The content and uptake of macronutrients and the value of ionic ratios
  96. The Effect of Macroalgal Extracts and Near Infrared Radiation on Germination of Soybean Seedlings: Preliminary Research Results
  97. Content of Zn, Cd and Pb in purple moor-grass in soils heavily contaminated with heavy metals around a zinc and lead ore tailing landfill
  98. Topical Issue on Research for Natural Bioactive Products
  99. Synthesis of (±)-3,4-dimethoxybenzyl-4-methyloctanoate as a novel internal standard for capsinoid determination by HPLC-ESI-MS/MS(QTOF)
  100. Repellent activity of monoterpenoid esters with neurotransmitter amino acids against yellow fever mosquito, Aedes aegypti
  101. Effect of Flammulina velutipes (golden needle mushroom, eno-kitake) polysaccharides on constipation
  102. Bioassay-directed fractionation of a blood coagulation factor Xa inhibitor, betulinic acid from Lycopus lucidus
  103. Antifungal and repellent activities of the essential oils from three aromatic herbs from western Himalaya
  104. Chemical composition and microbiological evaluation of essential oil from Hyssopus officinalis L. with white and pink flowers
  105. Bioassay-guided isolation and identification of Aedes aegypti larvicidal and biting deterrent compounds from Veratrum lobelianum
  106. α-Terpineol, a natural monoterpene: A review of its biological properties
  107. Utility of essential oils for development of host-based lures for Xyleborus glabratus (Coleoptera: Curculionidae: Scolytinae), vector of laurel wilt
  108. Phenolic composition and antioxidant potential of different organs of Kazakh Crataegus almaatensis Pojark: A comparison with the European Crataegus oxyacantha L. flowers
  109. Isolation of eudesmane type sesquiterpene ketone from Prangos heyniae H.Duman & M.F.Watson essential oil and mosquitocidal activity of the essential oils
  110. Comparative analysis of the polyphenols profiles and the antioxidant and cytotoxicity properties of various blue honeysuckle varieties
  111. Special Issue on ICCESEN 2017
  112. Modelling world energy security data from multinomial distribution by generalized linear model under different cumulative link functions
  113. Pine Cone and Boron Compounds Effect as Reinforcement on Mechanical and Flammability Properties of Polyester Composites
  114. Artificial Neural Network Modelling for Prediction of SNR Effected by Probe Properties on Ultrasonic Inspection of Austenitic Stainless Steel Weldments
  115. Calculation and 3D analyses of ERR in the band crack front contained in a rectangular plate made of multilayered material
  116. Improvement of fuel properties of biodiesel with bioadditive ethyl levulinate
  117. Properties of AlSi9Cu3 metal matrix micro and nano composites produced via stir casting
  118. Investigation of Antibacterial Properties of Ag Doped TiO2 Nanofibers Prepared by Electrospinning Process
  119. Modeling of Total Phenolic contents in Various Tea samples by Experimental Design Methods
  120. Nickel doping effect on the structural and optical properties of indium sulfide thin films by SILAR
  121. The effect mechanism of Ginnalin A as a homeopathic agent on various cancer cell lines
  122. Excitation functions of proton induced reactions of some radioisotopes used in medicine
  123. Oxide ionic conductivity and microstructures of Pr and Sm co-doped CeO2-based systems
  124. Rapid Synthesis of Metallic Reinforced in Situ Intermetallic Composites in Ti-Al-Nb System via Resistive Sintering
  125. Oxidation Behavior of NiCr/YSZ Thermal Barrier Coatings (TBCs)
  126. Clustering Analysis of Normal Strength Concretes Produced with Different Aggregate Types
  127. Magnetic Nano-Sized Solid Acid Catalyst Bearing Sulfonic Acid Groups for Biodiesel Synthesis
  128. The biological activities of Arabis alpina L. subsp. brevifolia (DC.) Cullen against food pathogens
  129. Humidity properties of Schiff base polymers
  130. Free Vibration Analysis of Fiber Metal Laminated Straight Beam
  131. Comparative study of in vitro antioxidant, acetylcholinesterase and butyrylcholinesterase activity of alfalfa (Medicago sativa L.) collected during different growth stages
  132. Isothermal Oxidation Behavior of Gadolinium Zirconate (Gd2Zr2O7) Thermal Barrier Coatings (TBCs) produced by Electron Beam Physical Vapor Deposition (EB-PVD) technique
  133. Optimization of Adsorption Parameters for Ultra-Fine Calcite Using a Box-Behnken Experimental Design
  134. The Microstructural Investigation of Vermiculite-Infiltrated Electron Beam Physical Vapor Deposition Thermal Barrier Coatings
  135. Modelling Porosity Permeability of Ceramic Tiles using Fuzzy Taguchi Method
  136. Experimental and theoretical study of a novel naphthoquinone Schiff base
  137. Physicochemical properties of heat treated sille stone for ceramic industry
  138. Sand Dune Characterization for Preparing Metallurgical Grade Silicon
  139. Catalytic Applications of Large Pore Sulfonic Acid-Functionalized SBA-15 Mesoporous Silica for Esterification
  140. One-photon Absorption Characterizations, Dipole Polarizabilities and Second Hyperpolarizabilities of Chlorophyll a and Crocin
  141. The Optical and Crystallite Characterization of Bilayer TiO2 Films Coated on Different ITO layers
  142. Topical Issue on Bond Activation
  143. Metal-mediated reactions towards the synthesis of a novel deaminolysed bisurea, dicarbamolyamine
  144. The structure of ortho-(trifluoromethyl)phenol in comparison to its homologues – A combined experimental and theoretical study
  145. Heterogeneous catalysis with encapsulated haem and other synthetic porphyrins: Harnessing the power of porphyrins for oxidation reactions
  146. Recent Advances on Mechanistic Studies on C–H Activation Catalyzed by Base Metals
  147. Reactions of the organoplatinum complex [Pt(cod) (neoSi)Cl] (neoSi = trimethylsilylmethyl) with the non-coordinating anions SbF6– and BPh4–
  148. Erratum
  149. Investigation on Two Compounds of O, O’-dithiophosphate Derivatives as Corrosion Inhibitors for Q235 Steel in Hydrochloric Acid Solution
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 11.12.2025 von https://www.degruyterbrill.com/document/doi/10.1515/chem-2018-0096/html
Button zum nach oben scrollen