Home Physical Sciences Synthesis, characterization, and photocatalysis of a rare-earth cerium/silver/zinc oxide inorganic nanocomposite
Article Open Access

Synthesis, characterization, and photocatalysis of a rare-earth cerium/silver/zinc oxide inorganic nanocomposite

  • Jiang Wu EMAIL logo , Qiao Li , Guoliang Zhang and Yuguang Lv EMAIL logo
Published/Copyright: May 12, 2022
Download Article (PDF)
Become an author with De Gruyter Brill
Submit Manuscript Author Information
Green Processing and Synthesis
From the journal Green Processing and Synthesis Volume 11 Issue 1

Abstract

A cerium/silver/zinc oxide (Ce/Ag/ZnO) inorganic nanocomposite was synthesized through a homogeneous precipitation method. The characterization and photocatalysis procedures were carried out by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflection spectroscopy, and photocatalytic performance. The characteristic absorption peak of ZnO was near 432 cm−1, no absorption was observed peak near 1,083 cm−1 for CeO2 and ZnO, the absorption peak near 721 cm−1 was generated by the vibration of CeO2, and the absorption peak had an obvious blue shift. The XRD results showed a strong interfacial interaction among Ag, CeO2 and ZnO to form a core–shell structure. The SEM image showed that the Ce/Ag/ZnO samples are approximately 25 nm. The XPS spectra showed that the Ce/Ag/ZnO nanocomposite powders were successfully prepared. The UV-Vis diffuse reflection spectra showed that the Ce/Ag/ZnO nanocomposites reduced the band gap and increased the ability of visible light response. The addition of rare earth Ce could inhibit the recombination of ZnO photoelectron pairs and improve the photocatalytic effect. Therefore, Ce/Ag/ZnO exhibited good characteristics of nanocomposite materials and good photocatalytic ability.

Keywords: cerium/silver/zinc oxide; nanocomposite; characterization; band gap; photocatalysis ability

1 Introduction

Currently, nanoinorganic antibacterial agents, which have advantages such as small size effects, macroscopic quantum tunneling, and surface effects, exhibit properties including a broad antibacterial spectrum, effective antibacterial activity, good stability, and no antibiotic resistance mechanism [1,2,3,4]. Rare earth elements have active coordination properties due to their unique electron configuration and have attracted much attention in biomedical fields such as antibacterial, antitumor, and biocompatibility [5,6]. In the early stage, our research group carried out the synthesis and characterization of the nanocomposite Sm/Ag/TiO2 and examined its antibacterial properties [7]. Cerium (Ce) is the most abundant rare earth metal in lanthanides [8], and it possesses two oxidation states, Ce3+ and Ce4+. Cerium oxide (CeO2) has a large number of surface defects, high oxygen storage capacity, excellent chemical and structural stability, and a wide range of applications in alloys, phosphors, catalysis, magnetism, medicine, and other fields [9,10]. Silver nanoparticles, titanium dioxide nanoparticles, and zinc oxide nanoparticles are common inorganic antibacterial agents that are used in stomatology. Among them, zinc oxide nanoparticles are antibacterial agents that are multifunctional and environmentally friendly. Zinc oxide nanoparticles exhibit chemical stability, biocompatibility, photocatalytic bactericidal activity, broad-spectrum antibacterial ability, and low bacterial resistance [11]. Nanozinc oxide is mainly used in science, electronics, ceramics, medicine, textiles, and coating industries [12]. Silver nanoparticles have a good antibacterial effect, long release cycle, and low toxicity to mammalian tissues. The composite of the three components can produce a synergistic effect to improve its biocompatibility, reduce the toxicity of materials, and obtain a better antibacterial effect.

Therefore, nanocomposite Ce/Ag/ZnO was synthesized by the homogeneous precipitation method. The main objective of this experiment was to study the characterization and photocatalysis of the inorganic nanomaterial Ce/Ag/ZnO. This study provided necessary data to support this antibacterial material in medical applications.

2 Materials and methods

2.1 Preparation of the inorganic Ce/Ag/ZnO nanomaterials

The solution was prepared by dissolving 12 g of Zn(NO3)2·6(H2O) in 200 mL of deionized water, dissolving 0.12 g of silver nitrate and 0.12 g of cerium nitrate tetrahydrate in the above zinc nitrate solution, and fully mixing the solution. Then, 300 mL of 0.25 mol·L−1 NaOH solution was slowly added to the mixture at a rate of 3 drops·min−1 with constant stirring, and a white precipitate was obtained. The precipitate was washed with deionized water and anhydrous ethanol three times and then dried at 70°C for 4 h to obtain the precursor. Then, the precursor was annealed at 300°C, 400°C, and 500°C for 4 h in a tube resistance furnace. Finally, the sample powder Ce/Ag/ZnO was obtained.

2.2 Characteristic analysis

The ZnO, Ag/ZnO, and Ce/Ag/ZnO powders were characterized by Fourier transform infrared (FT-IR) spectroscopy (BRUKER VERTEX70). The Ce/Ag/ZnO powders were characterized by X-ray diffraction (BRUKER D8 ADVANCE) with a Cu target X-ray tube at 40 kV and 30 mA and a scanning range of 20–80°. The particulate morphology of Ce/Ag/ZnO was observed by scanning electron microscopy (HITACHI S-4800). The Ag/ZnO and Ce/Ag/ZnO spectra were analyzed by X-ray photoelectron spectroscopy (Thermo Scientific K-Alpha Nexsa) with Al Kα X-ray, and the binding energy standard was C1s = 284.80 eV. The Ag/ZnO and Ce/Ag/ZnO spectra were analyzed by UV-Vis diffuse reflection spectroscopy (UV-3600).

2.3 Photocatalytic performance

A 300 mL methyl orange solution with a certain concentration was prepared under a normal temperature, and then, a certain concentration of sample reserve solution and a certain amount of buffer solution were added. After stirring in a dark room for 30 min, ultrasonic dispersion was performed for 3 min, a UV lamp was applied to irradiate the solution 15 cm away from the liquid level, and 5 mL of solution was removed every 20 min. The absorbance A was measured at 464 nm. The standard curve equation of methyl orange concentration and absorbance was obtained as follows:

(1) A = 0.0715 C + 0.013

According to the curve equation, the degradation rate was

(2) X = ( C 0 − C t ) / C 0

where C 0 and C t are the initial concentration of methyl orange and the concentration at time t, respectively. The degradation rate of methyl orange was proportional to photocatalysis.

3 Results and discussion

3.1 Fourier transform infrared spectroscopy analysis

Figure 1 shows that in the infrared spectra of the ZnO, Ag/ZnO, and Ce/Ag/ZnO nanocomposites, there was a wide absorption peak of –OH near 3,440 cm−1. This result showed that there was a large amount of hydroxide in the samples. The absorption peak near 1,647 cm−1 was the H–O–H bending vibration peak in free water. The absorption peak near 721 cm−1 was generated by the vibration of CeO2, and the absorption peak had an obvious blue shift. The characteristic absorption peak of ZnO was near 432 cm−1. CeO2 and ZnO had no absorption peak near 1,083 cm−1, and the Ce–O–Zn bond absorption peak was possibly formed due to bond cooperation between CeO2 and ZnO. These results showed that the Ce–O–Zn bond might be formed during the synthesis of Ce/Ag/ZnO composite powder, which was beneficial in improving the properties of the composite powder.

Figure 1 FT-IR of ZnO, Ag-ZnO, and Ce/Ag/ZnO spectra.
Figure 1

FT-IR of ZnO, Ag-ZnO, and Ce/Ag/ZnO spectra.

3.2 XRD analysis

Figure 2 shows the XRD patterns of the ZnO, Ag/ZnO, and Ce/Ag/ZnO nanocomposites. Compared with the XRD peaks of the ZnO and Ag nanoparticles, the Ag nuclei were completely covered by Ce and ZnO shells, so the diffraction peaks of Ag nuclei were lower than those of the pure Ag nanoparticles. In the Ce/Ag/ZnO nanostructures, no obvious shift was observed in the Ag and ZnO diffraction peaks, which indicated that there was a strong interfacial interaction among Ag, CeO2, and ZnO to form a core–shell structure.

Figure 2 Powder XRD analysis of ZnO, Ag/ZnO, and Ce/Ag/ZnO.
Figure 2

Powder XRD analysis of ZnO, Ag/ZnO, and Ce/Ag/ZnO.

The diffraction peaks at 2θ = 28.58, 33.12, 47.54, and 56.42° were consistent with the characteristic peaks of the JCHS CeO2 standard card. The diffraction peaks at 2θ = 31.76, 34.42, 36.25, 47.53, and 56.6° were consistent with the characteristic peaks of the JCHS ZnO standard cards. The 2θ = 28.40, 33.34, 69.58, and 76.66° diffraction peaks were consistent with the characteristic peaks of the JCHS Ag/ZnO standard cards. The samples were a mixture of CeO2, ZnO, and Ag/ZnO. The prepared Ce/Ag/ZnO nanocomposite powders were not only mixed at the atomic level of CeO2, ZnO, and Ag/ZnO but also had Ce–O–Zn bonds. The results showed that the Ce/Ag/ZnO nanocomposites were successfully prepared.

3.3 SEM measurements

The particle sizes of the two samples are relatively uniform, and there is a small amount of agglomeration (Figure 3). The average particle size of the Ag/ZnO samples is approximately 30 nm, and that of the Ce/Ag/ZnO samples is approximately 25 nm, which is in good agreement with the predicted value of Scherrer’s formula.

Figure 3 SEM patterns of Ag/ZnO and Ce/Ag/ZnO: (a) Ag/ZnO, (b) Ce/Ag/ZnO.
Figure 3

SEM patterns of Ag/ZnO and Ce/Ag/ZnO: (a) Ag/ZnO, (b) Ce/Ag/ZnO.

The structure of the Ce/Ag/ZnO nanocomposites was magnified 10,000 times under SEM, with a thickness of approximately 0.1–0.3 μm and a diameter of approximately 1 μm (Figure 4). After ion modification, the original physical structure was not changed, which was consistent with the characterization results.

Figure 4 The structure of the Ce/Ag/ZnO nanocomposites magnified 10,000 times under SEM.
Figure 4

The structure of the Ce/Ag/ZnO nanocomposites magnified 10,000 times under SEM.

3.4 XPS spectra

Figures 5 and 6 show that the C–C/C–H binding energy of C1s adsorbed carbon was 284.8 eV to calibrate all spectral peaks, and Avantage software was used to perform peak fitting for the XPS data. The XPS spectra showed that the C1s, O1s, N1s, Zn2p, Ag3d, and Ce3d were observed. The XPS spectra of Ag/ZnO and Ce/Ag/ZnO showed that the binding energy deviation was ±0.2 eV, and the Ce/Ag/ZnO nanocomposites were successfully prepared.

Figure 5 Full spectrum XPS analysis diagram of Ag/ZnO.
Figure 5

Full spectrum XPS analysis diagram of Ag/ZnO.

Figure 6 Full spectrum XPS analysis diagram of Ce/Ag/ZnO.
Figure 6

Full spectrum XPS analysis diagram of Ce/Ag/ZnO.

3.5 UV-Vis diffuse reflection spectroscopy

When the formation rate of the crystal nucleus is greater than its growth rate, the UV absorption of the product is related to the particle size; the smaller the particle size, the higher the UV absorption value. Figures 7 and 8 show that the UV shielding performance of ternary composite powder was better than that of binary powder. The band gap width corresponding to the Ag/ZnO and Ce/Ag/ZnO composite samples was calculated by the formula. The figure shows that the absorption band of the Ag/ZnO composite samples was approximately 410 nm, E g = 4.68 eV. The absorption band of the Ce/Ag/ZnO composite samples was about 415 nm, E g = 4.62 eV. The results showed that the preparation of Ce/Ag/ZnO composite samples greatly reduced the band gap width, increased the ability of composite samples to have a visible light response, and improved the photocatalytic efficiency [13].

Figure 7 UV-Vis diffuse reflection spectroscopy and band gap width of Ag/ZnO.
Figure 7

UV-Vis diffuse reflection spectroscopy and band gap width of Ag/ZnO.

Figure 8 UV-Vis diffuse reflection spectroscopy and band gap width of Ag/ZnO and Ce/Ag/ZnO.
Figure 8

UV-Vis diffuse reflection spectroscopy and band gap width of Ag/ZnO and Ce/Ag/ZnO.

3.6 Photocatalytic analysis

The anionic surfactants used in the experiment were sodium dodecylbenzene sulfonate (SDBS) and sodium polyacrylate (PAAS). The experimental conditions included a pH of 7.0, the methyl orange solution in the concentration range of 0–2.0 × 10−2 g·L−1, and the sample solution at a concentration of 8 mg·L−1. Figure 9 shows that the degradation rate of the Ce/Ag/ZnO samples to methyl orange was greater than that of the Ag/ZnO samples, and the degradation rate of methyl orange in the surfactant group was almost zero. Figure 10 shows that the degradation rate of methyl orange by adding surfactant PAAS to the sample was significantly higher than that by adding surfactant SDBS, and the maximum degradation rate reached approximately 90%. Therefore, the above results showed that the addition of rare earth Ce could inhibit the recombination of ZnO photoelectron pairs and improve the photocatalytic effect [14]. At the same time, the results showed that the performance of the surfactant PAAS is better than that of SDBS, and it could improve the dispersion of nanoparticles, reduce the surface energy, and improve the photocatalysis of Ce/Ag/ZnO.

Figure 9 Under certain conditions, the Ce/Ag/ZnO and Ag/ZnO sample degradation rates of the methyl orange contrast curve. (1) the Ce/Ag/ZnO sample group, (2) the Ag/ZnO sample group, (3) surfactant SDBS with no samples in the control group, (4) surfactant PAAS with no samples in the control group.
Figure 9

Under certain conditions, the Ce/Ag/ZnO and Ag/ZnO sample degradation rates of the methyl orange contrast curve. (1) the Ce/Ag/ZnO sample group, (2) the Ag/ZnO sample group, (3) surfactant SDBS with no samples in the control group, (4) surfactant PAAS with no samples in the control group.

Figure 10 Ce/Ag/ZnO and Ag/ZnO sample degradation rates of the methyl orange contrast curve after adding different surfactants. (1) and (2) to join surfactant PAAS Ce/Ag/ZnO and Ag/ZnO samples, respectively; (3) and (4) are Ce/Ag/ZnO and Ag/ZnO samples with added SDBS, respectively.
Figure 10

Ce/Ag/ZnO and Ag/ZnO sample degradation rates of the methyl orange contrast curve after adding different surfactants. (1) and (2) to join surfactant PAAS Ce/Ag/ZnO and Ag/ZnO samples, respectively; (3) and (4) are Ce/Ag/ZnO and Ag/ZnO samples with added SDBS, respectively.

In the study of the nanocomposite Sm/Ag/TiO2, we found that the photocatalytic activity was proportional to the antibacterial activity [7]. When the energy of incoming radiation from the outside exceeds the band gap of the nanoparticle, the electron-stimulated transition produces a highly active photogenic hole (h+) and photogenic electron (e−). e− and h+ react with oxygen, hydroxyl, and water adsorbed on the surface of the material to produce ROS such as hydroxide, oxygen anions, and hydrogen peroxide, thus inducing optical toxicity [15]. Reactive oxygen species with strong oxidation damage the integrity of cells, affect the metabolism of cellular energy, interfere with DNA replication, destroy protein expression, and eventually lead to cell apoptosis [16,17]. In addition, we found in the antibacterial test that the MIC and MBC of Ce/Ag/ZnO were 0.156 and 0.313 mg·mL−1, respectively [18]. According to “The chemical industry standards of the People’s Republic of China: inorganic antibacterial performance and evaluation,” a material that exhibits a bacteriostatic effect is considered to be a bacteriostatic agent when used with a concentration of less than 800 μg·mL−1.

Therefore, the photocatalytic properties of nanomaterials can induce optical toxicity and thus exert antibacterial activity [19], which can also indirectly indicate that the Ce/Ag/ZnO composite has good antibacterial activity.

4 Conclusion

This study showed that Ce/Ag/ZnO exhibited good nanocomposite material characteristics and photocatalysis ability. This study also found that the surfactant sodium polyacrylate (PAAS) could improve the photocatalytic activity of Ce/Ag/ZnO nanocomposites. Therefore, the feasibility of the combined application of Ce/Ag/ZnO nanocomposites with surfactant sodium polyacrylate (PAAS) and oral therapy materials should be explored in the future. This study provided the necessary data to support this kind of antibacterial material in antibacterial mechanisms and medical applications.

tel: +86-454-8625581

Acknowledgment

The authors thank Prof. Yuguang Lv (College of Pharmacy, Jiamusi University) for his assistance in the nanocomposite research. This work was financially supported by the Basic Scientific Research Project of Heilongjiang Provincial Colleges and Universities (No. 2020-KYYWF-0246) and the Project Doctoral Special Research Fund of Jiamusi University (JMSUBZ2020-08).

  1. Funding information: This work was financially supported by the Project Doctoral Special Research Fund of Jiamusi University (JMSUBZ2020-08) and the Basic Scientific Research Project of Heilongjiang Provincial Colleges and Universities (2020-KYYWF-0246).

  2. Author contributions: Jiang Wu: writing – original draft, writing – review and editing, project administration; Qiao Li: methodology, formal analysis; Guoliang Zhang: methodology, visualization; Yuguang Lv: writing – review and editing, project administration.

  3. Conflict of interest: Authors state no conflict of interest.

References

[1] Hajipour MJ, Fromm KM, Ash Karran AA, Jimenez de Aberasturi D, de Larramendi IR, Rojo T, et al. Antibacterial proper ties of nanoparticles. Trends Biotechnol. 2012;30(10):499–511. 10.1016/j.tibtech.2012.06.004.Search in Google Scholar

[2] Weir E, Lawlor A, Whelan A, Regan F. The use of nanoparticles in anti-microbial materials and their characterization. Analyst. 2008;133(7):835–45. 10.1039/b715532h.Search in Google Scholar

[3] Ge L, Li Q, Wang M, Ouyang J, Li X, Xing MM. Nanosilver particles in medical applications: synthesis, performance, and toxicity. Int J Nanomed. 2014;9:2399–407. 10.2147/IJN.S55015.Search in Google Scholar

[4] Boulaiz H, Alvarez PJ, Ramirez A, Marchal JA, Prados J, Rodríguez-Serrano F, et al. Nanomedicine: application areas and development prospects. Int J Mol Sci. 2011;12(5):3303–21. 10.3390/ijms12053303.Search in Google Scholar

[5] Maciuca AM, Munteanu AC, Mihaila M, Badea M, Olar R, Nitulescu GM, et al. Rare-earth metal complexes of the antibacterial drug oxolinic acid: synthesis, characterization, DNA/protein binding and cytotoxicity studies. Molecules. 2020;5(22):5418. 10.3390/molecules25225418.Search in Google Scholar

[6] Wang H, Liao B, Lu T, Ai Y, Liu G. Enhanced visible-light photocatalytic degradation of tetracycline by a novel hollow BiOCl@CeO2 hetero structured microspheres: Structural characterization and reaction mechanism. J Hazard Mater. 2020;385:121552. 10.1016/j.jhazmat.2019.121552.Search in Google Scholar

[7] Wu J, Zhang G, Liu J, Gao H, Song C, Du H, et al. Synthesis, characteristics, and antibacterial activity of a rare-earth samarium/silver/titanium dioxide inorganic nanomaterials. J Rare Earths. 2014;32(8):727–31. 10.1016/S1002-0721(14)60133-2.Search in Google Scholar

[8] Wu K, Sun LD, Yan CH. Recent progress in well-controlled synthesis of ceria-based nanocatalysts towards enhanced catalytic performance. Adv Energy Mater. 2016;6(17):1600501. 10.1002/aenm.201600501.Search in Google Scholar

[9] Xu Y, Mofarah SS, Mehmood R, Cazorla C, Koshy P, Sorrell CC. Design strategies for ceria nanomaterials: untangling key mechanistic concepts. Mater Horiz. 2021;8(1):102–23. 10.1039/D0MH00654H.Search in Google Scholar

[10] Raza Naqvi ST, Shirinfar B, Majeed S, Najam-Ul-Haq M, Hussain D, Iqbal T, et al. Synthesis, design and sensing applications of nanostructured ceria-based materials. Analyst. 2018;143(23):5610–28. 10.1039/C8AN01268G.Search in Google Scholar PubMed

[11] Khan ST, Al-khedhair y AA, Musarrat J. ZnO and TiO2 nanoparticles as novel antimicrobial agents for oral hygiene: a review. J Nanopart Res. 2015;17(6):1–16. 10.1007/s11051-015-3074-6.Search in Google Scholar

[12] Talebian N, Amininezhad SM, Doudi. M. Controllable synthesis of ZnO nanoparticles and their morphology-dependent antibacterial and optical properties. J Photochem Photobiol B: Biol. 2013;120(2):66–73. 10.1016/j.jphotobiol.2013.01.004.Search in Google Scholar PubMed

[13] Lang J, Wang J, Zhang Q, Li X, Han Q, Wei M, et al. Chemical precipitation synthesis and significant enhancement in photocatalytic activity of Ce-doped ZnO nanoparticles. Ceram Int. 2016;42(12):14175–81. 10.1016/j.ceramint.2016.06.042.Search in Google Scholar

[14] Changlin YU, Kai Y, Jimmy YU, Peng P, Fangfang CAO, Xin LI, et al. Effects of rare earth Ce doping on the structure and photocatalytic performance of ZnO. Acta Physico- Chim Sin. 2011;27(2):505–12. 10.3866/PKU.WHXB20110230.Search in Google Scholar

[15] Dutta RK, Nenavathu BP, Gangishetty MK, Reddy AV. Studies on antibacterial activity of Zn O nanoparticles by ROS induced lipid peroxidation. Colloids Surf B Biointerfaces. 2012;94:143–50. 10.1016/j.colsurfb.2012.01.046.Search in Google Scholar PubMed

[16] Zhang H, Li Z, Dai C, Wang P, Fan S, Yu B, et al. Antibacterial properties and mechanism of selenium nanoparticles synthesized by Providencia sp. DCX. Env Res. 2020;194:110630. 10.1016/j.envres.2020.110630.Search in Google Scholar PubMed

[17] Rani V, Deep G, Singh RK, Palle K, Yadav. UCS. Oxidative stress and metabolic disorders: Pathogenesis and therapeutic strategies. Life Sci. 2016;148:183–93. 10.1016/j.lfs.2016.02.002.Search in Google Scholar PubMed

[18] Liu LS, Wu J, Zhang GL, Lv YG. Study on the antibacterial mechanism of Oxidative stress in Candida albicans by Using Ce/Ag/ZnO nanocomposites. Oral Med (China). 2021;41(10):878–82. 10.13591/j.cnki.kqyx.2021.10.003.Search in Google Scholar

[19] Akbar A, Anal AK. Zinc oxide nanoparticles loaded active packaging, a challenge study against Salmonella typhimurium and Staphylococcus aureus in ready-to-eat poultry meat. Food Control. 2014;38:88–95. 10.1016/j.foodcont.2013.09.065.Search in Google Scholar
Received: 2022-02-24
Revised: 2022-04-13
Accepted: 2022-04-20
Published Online: 2022-05-12

© 2022 Jiang Wu et al., published by De Gruyter

This work is licensed under the Creative Commons Attribution 4.0 International License.

Articles in the same Issue

  1. Research Articles
  2. Kinetic study on the reaction between Incoloy 825 alloy and low-fluoride slag for electroslag remelting
  3. Black pepper (Piper nigrum) fruit-based gold nanoparticles (BP-AuNPs): Synthesis, characterization, biological activities, and catalytic applications – A green approach
  4. Protective role of foliar application of green-synthesized silver nanoparticles against wheat stripe rust disease caused by Puccinia striiformis
  5. Effects of nitrogen and phosphorus on Microcystis aeruginosa growth and microcystin production
  6. Efficient degradation of methyl orange and methylene blue in aqueous solution using a novel Fenton-like catalyst of CuCo-ZIFs
  7. Synthesis of biological base oils by a green process
  8. Efficient pilot-scale synthesis of the key cefonicid intermediate at room temperature
  9. Synthesis and characterization of noble metal/metal oxide nanoparticles and their potential antidiabetic effect on biochemical parameters and wound healing
  10. Regioselectivity in the reaction of 5-amino-3-anilino-1H-pyrazole-4-carbonitrile with cinnamonitriles and enaminones: Synthesis of functionally substituted pyrazolo[1,5-a]pyrimidine derivatives
  11. A numerical study on the in-nozzle cavitating flow and near-field atomization of cylindrical, V-type, and Y-type intersecting hole nozzles using the LES-VOF method
  12. Synthesis and characterization of Ce-doped TiO2 nanoparticles and their enhanced anticancer activity in Y79 retinoblastoma cancer cells
  13. Aspects of the physiochemical properties of SARS-CoV-2 to prevent S-protein receptor binding using Arabic gum
  14. Sonochemical synthesis of protein microcapsules loaded with traditional Chinese herb extracts
  15. MW-assisted hydrolysis of phosphinates in the presence of PTSA as the catalyst, and as a MW absorber
  16. Fabrication of silicotungstic acid immobilized on Ce-based MOF and embedded in Zr-based MOF matrix for green fatty acid esterification
  17. Superior photocatalytic degradation performance for gaseous toluene by 3D g-C3N4-reduced graphene oxide gels
  18. Catalytic performance of Na/Ca-based fluxes for coal char gasification
  19. Slow pyrolysis of waste navel orange peels with metal oxide catalysts to produce high-grade bio-oil
  20. Development and butyrylcholinesterase/monoamine oxidase inhibition potential of PVA-Berberis lycium nanofibers
  21. Influence of biosynthesized silver nanoparticles using red alga Corallina elongata on broiler chicks’ performance
  22. Green synthesis, characterization, cytotoxicity, and antimicrobial activity of iron oxide nanoparticles using Nigella sativa seed extract
  23. Vitamin supplements enhance Spirulina platensis biomass and phytochemical contents
  24. Malachite green dye removal using ceramsite-supported nanoscale zero-valent iron in a fixed-bed reactor
  25. Green synthesis of manganese-doped superparamagnetic iron oxide nanoparticles for the effective removal of Pb(ii) from aqueous solutions
  26. Desalination technology for energy-efficient and low-cost water production: A bibliometric analysis
  27. Biological fabrication of zinc oxide nanoparticles from Nepeta cataria potentially produces apoptosis through inhibition of proliferative markers in ovarian cancer
  28. Effect of stabilizers on Mn ZnSe quantum dots synthesized by using green method
  29. Calcium oxide addition and ultrasonic pretreatment-assisted hydrothermal carbonization of granatum for adsorption of lead
  30. Fe3O4@SiO2 nanoflakes synthesized using biogenic silica from Salacca zalacca leaf ash and the mechanistic insight into adsorption and photocatalytic wet peroxidation of dye
  31. Facile route of synthesis of silver nanoparticles templated bacterial cellulose, characterization, and its antibacterial application
  32. Synergistic in vitro anticancer actions of decorated selenium nanoparticles with fucoidan/Reishi extract against colorectal adenocarcinoma cells
  33. Preparation of the micro-size flake silver powders by using a micro-jet reactor
  34. Effect of direct coal liquefaction residue on the properties of fine blue-coke-based activated coke
  35. Integration of microwave co-torrefaction with helical lift for pellet fuel production
  36. Cytotoxicity of green-synthesized silver nanoparticles by Adansonia digitata fruit extract against HTC116 and SW480 human colon cancer cell lines
  37. Optimization of biochar preparation process and carbon sequestration effect of pruned wolfberry branches
  38. Anticancer potential of biogenic silver nanoparticles using the stem extract of Commiphora gileadensis against human colon cancer cells
  39. Fabrication and characterization of lysine hydrochloride Cu(ii) complexes and their potential for bombing bacterial resistance
  40. First report of biocellulose production by an indigenous yeast, Pichia kudriavzevii USM-YBP2
  41. Biosynthesis and characterization of silver nanoparticles prepared using seeds of Sisymbrium irio and evaluation of their antifungal and cytotoxic activities
  42. Synthesis, characterization, and photocatalysis of a rare-earth cerium/silver/zinc oxide inorganic nanocomposite
  43. Developing a plastic cycle toward circular economy practice
  44. Fabrication of CsPb1−xMnxBr3−2xCl2x (x = 0–0.5) quantum dots for near UV photodetector application
  45. Anti-colon cancer activities of green-synthesized Moringa oleifera–AgNPs against human colon cancer cells
  46. Phosphorus removal from aqueous solution by adsorption using wetland-based biochar: Batch experiment
  47. A low-cost and eco-friendly fabrication of an MCDI-utilized PVA/SSA/GA cation exchange membrane
  48. Synthesis, microstructure, and phase transition characteristics of Gd/Nd-doped nano VO2 powders
  49. Biomediated synthesis of ZnO quantum dots decorated attapulgite nanocomposites for improved antibacterial properties
  50. Preparation of metal–organic frameworks by microwave-assisted ball milling for the removal of CR from wastewater
  51. A green approach in the biological base oil process
  52. A cost-effective and eco-friendly biosorption technology for complete removal of nickel ions from an aqueous solution: Optimization of process variables
  53. Protective role of Spirulina platensis liquid extract against salinity stress effects on Triticum aestivum L.
  54. Comprehensive physical and chemical characterization highlights the uniqueness of enzymatic gelatin in terms of surface properties
  55. Effectiveness of different accelerated green synthesis methods in zinc oxide nanoparticles using red pepper extract: Synthesis and characterization
  56. Blueprinting morpho-anatomical episodes via green silver nanoparticles foliation
  57. A numerical study on the effects of bowl and nozzle geometry on performances of an engine fueled with diesel or bio-diesel fuels
  58. Liquid-phase hydrogenation of carbon tetrachloride catalyzed by three-dimensional graphene-supported palladium catalyst
  59. The catalytic performance of acid-modified Hβ molecular sieves for environmentally friendly acylation of 2-methylnaphthalene
  60. A study of the precipitation of cerium oxide synthesized from rare earth sources used as the catalyst for biodiesel production
  61. Larvicidal potential of Cipadessa baccifera leaf extract-synthesized zinc nanoparticles against three major mosquito vectors
  62. Fabrication of green nanoinsecticides from agri-waste of corn silk and its larvicidal and antibiofilm properties
  63. Palladium-mediated base-free and solvent-free synthesis of aromatic azo compounds from anilines catalyzed by copper acetate
  64. Study on the functionalization of activated carbon and the effect of binder toward capacitive deionization application
  65. Co-chlorination of low-density polyethylene in paraffin: An intensified green process alternative to conventional solvent-based chlorination
  66. Antioxidant and photocatalytic properties of zinc oxide nanoparticles phyto-fabricated using the aqueous leaf extract of Sida acuta
  67. Recovery of cobalt from spent lithium-ion battery cathode materials by using choline chloride-based deep eutectic solvent
  68. Synthesis of insoluble sulfur and development of green technology based on Aspen Plus simulation
  69. Photodegradation of methyl orange under solar irradiation on Fe-doped ZnO nanoparticles synthesized using wild olive leaf extract
  70. A facile and universal method to purify silica from natural sand
  71. Green synthesis of silver nanoparticles using Atalantia monophylla: A potential eco-friendly agent for controlling blood-sucking vectors
  72. Endophytic bacterial strain, Brevibacillus brevis-mediated green synthesis of copper oxide nanoparticles, characterization, antifungal, in vitro cytotoxicity, and larvicidal activity
  73. Off-gas detection and treatment for green air-plasma process
  74. Ultrasonic-assisted food grade nanoemulsion preparation from clove bud essential oil and evaluation of its antioxidant and antibacterial activity
  75. Construction of mercury ion fluorescence system in water samples and art materials and fluorescence detection method for rhodamine B derivatives
  76. Hydroxyapatite/TPU/PLA nanocomposites: Morphological, dynamic-mechanical, and thermal study
  77. Potential of anaerobic co-digestion of acidic fruit processing waste and waste-activated sludge for biogas production
  78. Synthesis and characterization of ZnO–TiO2–chitosan–escin metallic nanocomposites: Evaluation of their antimicrobial and anticancer activities
  79. Nitrogen removal characteristics of wet–dry alternative constructed wetlands
  80. Structural properties and reactivity variations of wheat straw char catalysts in volatile reforming
  81. Microfluidic plasma: Novel process intensification strategy
  82. Antibacterial and photocatalytic activity of visible-light-induced synthesized gold nanoparticles by using Lantana camara flower extract
  83. Antimicrobial edible materials via nano-modifications for food safety applications
  84. Biosynthesis of nano-curcumin/nano-selenium composite and their potentialities as bactericides against fish-borne pathogens
  85. Exploring the effect of silver nanoparticles on gene expression in colon cancer cell line HCT116
  86. Chemical synthesis, characterization, and dose optimization of chitosan-based nanoparticles of clodinofop propargyl and fenoxaprop-p-ethyl for management of Phalaris minor (little seed canary grass): First report
  87. Double [3 + 2] cycloadditions for diastereoselective synthesis of spirooxindole pyrrolizidines
  88. Green synthesis of silver nanoparticles and their antibacterial activities
  89. Review Articles
  90. A comprehensive review on green synthesis of titanium dioxide nanoparticles and their diverse biomedical applications
  91. Applications of polyaniline-impregnated silica gel-based nanocomposites in wastewater treatment as an efficient adsorbent of some important organic dyes
  92. Green synthesis of nano-propolis and nanoparticles (Se and Ag) from ethanolic extract of propolis, their biochemical characterization: A review
  93. Advances in novel activation methods to perform green organic synthesis using recyclable heteropolyacid catalysis
  94. Limitations of nanomaterials insights in green chemistry sustainable route: Review on novel applications
  95. Special Issue: Use of magnetic resonance in profiling bioactive metabolites and its applications (Guest Editors: Plalanoivel Velmurugan et al.)
  96. Stomach-affecting intestinal parasites as a precursor model of Pheretima posthuma treated with anthelmintic drug from Dodonaea viscosa Linn.
  97. Anti-asthmatic activity of Saudi herbal composites from plants Bacopa monnieri and Euphorbia hirta on Guinea pigs
  98. Embedding green synthesized zinc oxide nanoparticles in cotton fabrics and assessment of their antibacterial wound healing and cytotoxic properties: An eco-friendly approach
  99. Synthetic pathway of 2-fluoro-N,N-diphenylbenzamide with opto-electrical properties: NMR, FT-IR, UV-Vis spectroscopic, and DFT computational studies of the first-order nonlinear optical organic single crystal
https://doi.org/10.1515/gps-2022-0051
Keywords for this article
cerium/silver/zinc oxide; nanocomposite; characterization; band gap; photocatalysis ability
Creative Commons
BY 4.0

Articles in the same Issue

  1. Research Articles
  2. Kinetic study on the reaction between Incoloy 825 alloy and low-fluoride slag for electroslag remelting
  3. Black pepper (Piper nigrum) fruit-based gold nanoparticles (BP-AuNPs): Synthesis, characterization, biological activities, and catalytic applications – A green approach
  4. Protective role of foliar application of green-synthesized silver nanoparticles against wheat stripe rust disease caused by Puccinia striiformis
  5. Effects of nitrogen and phosphorus on Microcystis aeruginosa growth and microcystin production
  6. Efficient degradation of methyl orange and methylene blue in aqueous solution using a novel Fenton-like catalyst of CuCo-ZIFs
  7. Synthesis of biological base oils by a green process
  8. Efficient pilot-scale synthesis of the key cefonicid intermediate at room temperature
  9. Synthesis and characterization of noble metal/metal oxide nanoparticles and their potential antidiabetic effect on biochemical parameters and wound healing
  10. Regioselectivity in the reaction of 5-amino-3-anilino-1H-pyrazole-4-carbonitrile with cinnamonitriles and enaminones: Synthesis of functionally substituted pyrazolo[1,5-a]pyrimidine derivatives
  11. A numerical study on the in-nozzle cavitating flow and near-field atomization of cylindrical, V-type, and Y-type intersecting hole nozzles using the LES-VOF method
  12. Synthesis and characterization of Ce-doped TiO2 nanoparticles and their enhanced anticancer activity in Y79 retinoblastoma cancer cells
  13. Aspects of the physiochemical properties of SARS-CoV-2 to prevent S-protein receptor binding using Arabic gum
  14. Sonochemical synthesis of protein microcapsules loaded with traditional Chinese herb extracts
  15. MW-assisted hydrolysis of phosphinates in the presence of PTSA as the catalyst, and as a MW absorber
  16. Fabrication of silicotungstic acid immobilized on Ce-based MOF and embedded in Zr-based MOF matrix for green fatty acid esterification
  17. Superior photocatalytic degradation performance for gaseous toluene by 3D g-C3N4-reduced graphene oxide gels
  18. Catalytic performance of Na/Ca-based fluxes for coal char gasification
  19. Slow pyrolysis of waste navel orange peels with metal oxide catalysts to produce high-grade bio-oil
  20. Development and butyrylcholinesterase/monoamine oxidase inhibition potential of PVA-Berberis lycium nanofibers
  21. Influence of biosynthesized silver nanoparticles using red alga Corallina elongata on broiler chicks’ performance
  22. Green synthesis, characterization, cytotoxicity, and antimicrobial activity of iron oxide nanoparticles using Nigella sativa seed extract
  23. Vitamin supplements enhance Spirulina platensis biomass and phytochemical contents
  24. Malachite green dye removal using ceramsite-supported nanoscale zero-valent iron in a fixed-bed reactor
  25. Green synthesis of manganese-doped superparamagnetic iron oxide nanoparticles for the effective removal of Pb(ii) from aqueous solutions
  26. Desalination technology for energy-efficient and low-cost water production: A bibliometric analysis
  27. Biological fabrication of zinc oxide nanoparticles from Nepeta cataria potentially produces apoptosis through inhibition of proliferative markers in ovarian cancer
  28. Effect of stabilizers on Mn ZnSe quantum dots synthesized by using green method
  29. Calcium oxide addition and ultrasonic pretreatment-assisted hydrothermal carbonization of granatum for adsorption of lead
  30. Fe3O4@SiO2 nanoflakes synthesized using biogenic silica from Salacca zalacca leaf ash and the mechanistic insight into adsorption and photocatalytic wet peroxidation of dye
  31. Facile route of synthesis of silver nanoparticles templated bacterial cellulose, characterization, and its antibacterial application
  32. Synergistic in vitro anticancer actions of decorated selenium nanoparticles with fucoidan/Reishi extract against colorectal adenocarcinoma cells
  33. Preparation of the micro-size flake silver powders by using a micro-jet reactor
  34. Effect of direct coal liquefaction residue on the properties of fine blue-coke-based activated coke
  35. Integration of microwave co-torrefaction with helical lift for pellet fuel production
  36. Cytotoxicity of green-synthesized silver nanoparticles by Adansonia digitata fruit extract against HTC116 and SW480 human colon cancer cell lines
  37. Optimization of biochar preparation process and carbon sequestration effect of pruned wolfberry branches
  38. Anticancer potential of biogenic silver nanoparticles using the stem extract of Commiphora gileadensis against human colon cancer cells
  39. Fabrication and characterization of lysine hydrochloride Cu(ii) complexes and their potential for bombing bacterial resistance
  40. First report of biocellulose production by an indigenous yeast, Pichia kudriavzevii USM-YBP2
  41. Biosynthesis and characterization of silver nanoparticles prepared using seeds of Sisymbrium irio and evaluation of their antifungal and cytotoxic activities
  42. Synthesis, characterization, and photocatalysis of a rare-earth cerium/silver/zinc oxide inorganic nanocomposite
  43. Developing a plastic cycle toward circular economy practice
  44. Fabrication of CsPb1−xMnxBr3−2xCl2x (x = 0–0.5) quantum dots for near UV photodetector application
  45. Anti-colon cancer activities of green-synthesized Moringa oleifera–AgNPs against human colon cancer cells
  46. Phosphorus removal from aqueous solution by adsorption using wetland-based biochar: Batch experiment
  47. A low-cost and eco-friendly fabrication of an MCDI-utilized PVA/SSA/GA cation exchange membrane
  48. Synthesis, microstructure, and phase transition characteristics of Gd/Nd-doped nano VO2 powders
  49. Biomediated synthesis of ZnO quantum dots decorated attapulgite nanocomposites for improved antibacterial properties
  50. Preparation of metal–organic frameworks by microwave-assisted ball milling for the removal of CR from wastewater
  51. A green approach in the biological base oil process
  52. A cost-effective and eco-friendly biosorption technology for complete removal of nickel ions from an aqueous solution: Optimization of process variables
  53. Protective role of Spirulina platensis liquid extract against salinity stress effects on Triticum aestivum L.
  54. Comprehensive physical and chemical characterization highlights the uniqueness of enzymatic gelatin in terms of surface properties
  55. Effectiveness of different accelerated green synthesis methods in zinc oxide nanoparticles using red pepper extract: Synthesis and characterization
  56. Blueprinting morpho-anatomical episodes via green silver nanoparticles foliation
  57. A numerical study on the effects of bowl and nozzle geometry on performances of an engine fueled with diesel or bio-diesel fuels
  58. Liquid-phase hydrogenation of carbon tetrachloride catalyzed by three-dimensional graphene-supported palladium catalyst
  59. The catalytic performance of acid-modified Hβ molecular sieves for environmentally friendly acylation of 2-methylnaphthalene
  60. A study of the precipitation of cerium oxide synthesized from rare earth sources used as the catalyst for biodiesel production
  61. Larvicidal potential of Cipadessa baccifera leaf extract-synthesized zinc nanoparticles against three major mosquito vectors
  62. Fabrication of green nanoinsecticides from agri-waste of corn silk and its larvicidal and antibiofilm properties
  63. Palladium-mediated base-free and solvent-free synthesis of aromatic azo compounds from anilines catalyzed by copper acetate
  64. Study on the functionalization of activated carbon and the effect of binder toward capacitive deionization application
  65. Co-chlorination of low-density polyethylene in paraffin: An intensified green process alternative to conventional solvent-based chlorination
  66. Antioxidant and photocatalytic properties of zinc oxide nanoparticles phyto-fabricated using the aqueous leaf extract of Sida acuta
  67. Recovery of cobalt from spent lithium-ion battery cathode materials by using choline chloride-based deep eutectic solvent
  68. Synthesis of insoluble sulfur and development of green technology based on Aspen Plus simulation
  69. Photodegradation of methyl orange under solar irradiation on Fe-doped ZnO nanoparticles synthesized using wild olive leaf extract
  70. A facile and universal method to purify silica from natural sand
  71. Green synthesis of silver nanoparticles using Atalantia monophylla: A potential eco-friendly agent for controlling blood-sucking vectors
  72. Endophytic bacterial strain, Brevibacillus brevis-mediated green synthesis of copper oxide nanoparticles, characterization, antifungal, in vitro cytotoxicity, and larvicidal activity
  73. Off-gas detection and treatment for green air-plasma process
  74. Ultrasonic-assisted food grade nanoemulsion preparation from clove bud essential oil and evaluation of its antioxidant and antibacterial activity
  75. Construction of mercury ion fluorescence system in water samples and art materials and fluorescence detection method for rhodamine B derivatives
  76. Hydroxyapatite/TPU/PLA nanocomposites: Morphological, dynamic-mechanical, and thermal study
  77. Potential of anaerobic co-digestion of acidic fruit processing waste and waste-activated sludge for biogas production
  78. Synthesis and characterization of ZnO–TiO2–chitosan–escin metallic nanocomposites: Evaluation of their antimicrobial and anticancer activities
  79. Nitrogen removal characteristics of wet–dry alternative constructed wetlands
  80. Structural properties and reactivity variations of wheat straw char catalysts in volatile reforming
  81. Microfluidic plasma: Novel process intensification strategy
  82. Antibacterial and photocatalytic activity of visible-light-induced synthesized gold nanoparticles by using Lantana camara flower extract
  83. Antimicrobial edible materials via nano-modifications for food safety applications
  84. Biosynthesis of nano-curcumin/nano-selenium composite and their potentialities as bactericides against fish-borne pathogens
  85. Exploring the effect of silver nanoparticles on gene expression in colon cancer cell line HCT116
  86. Chemical synthesis, characterization, and dose optimization of chitosan-based nanoparticles of clodinofop propargyl and fenoxaprop-p-ethyl for management of Phalaris minor (little seed canary grass): First report
  87. Double [3 + 2] cycloadditions for diastereoselective synthesis of spirooxindole pyrrolizidines
  88. Green synthesis of silver nanoparticles and their antibacterial activities
  89. Review Articles
  90. A comprehensive review on green synthesis of titanium dioxide nanoparticles and their diverse biomedical applications
  91. Applications of polyaniline-impregnated silica gel-based nanocomposites in wastewater treatment as an efficient adsorbent of some important organic dyes
  92. Green synthesis of nano-propolis and nanoparticles (Se and Ag) from ethanolic extract of propolis, their biochemical characterization: A review
  93. Advances in novel activation methods to perform green organic synthesis using recyclable heteropolyacid catalysis
  94. Limitations of nanomaterials insights in green chemistry sustainable route: Review on novel applications
  95. Special Issue: Use of magnetic resonance in profiling bioactive metabolites and its applications (Guest Editors: Plalanoivel Velmurugan et al.)
  96. Stomach-affecting intestinal parasites as a precursor model of Pheretima posthuma treated with anthelmintic drug from Dodonaea viscosa Linn.
  97. Anti-asthmatic activity of Saudi herbal composites from plants Bacopa monnieri and Euphorbia hirta on Guinea pigs
  98. Embedding green synthesized zinc oxide nanoparticles in cotton fabrics and assessment of their antibacterial wound healing and cytotoxic properties: An eco-friendly approach
  99. Synthetic pathway of 2-fluoro-N,N-diphenylbenzamide with opto-electrical properties: NMR, FT-IR, UV-Vis spectroscopic, and DFT computational studies of the first-order nonlinear optical organic single crystal
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 6.12.2025 from https://www.degruyterbrill.com/document/doi/10.1515/gps-2022-0051/html
Scroll to top button