Startseite Solid-State 17O NMR studies on Yttria-stabilized zirconia
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Solid-State 17O NMR studies on Yttria-stabilized zirconia

  • Tillmann Viefhaus und Klaus Müller
Veröffentlicht/Copyright: 31. Mai 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 97 Heft 5

Abstract

Variable temperature 17O NMR measurements, covering a temperature range from room temperature to 973K, were conducted on various samples from 17O enriched yttria-stabilized zirconia for the first time. It is shown that spin-lattice (T1) relaxation exhibits a strong temperature dependence originating from the motional displacements of the oxygen ions, and which is almost independent of the actual sample constitution. In addition, large temperature effects are found for the 17O NMR line widths (i.e. spin-spin relaxation) which – as the spin-lattice relaxation data – reflect the onset of the oxygen ion mobility. It is anticipated that the NMR line width effects are caused by motions on a length-scale which is different from that examined by spin-lattice relaxation.

Keywords: 17O NMR; Ionic conductors; Zirconia
* Correspondence address: Prof. Klaus Müller, Institut für Physikalische Chemie, Universität Stuttgart, Pfaffenwaldring 55, D-70569 Stuttgart, Germany, Tel.: +497116854470, Fax: +497116854467. E-mail:

Dedicated to Professor Dr. Fritz Aldinger on the occasion of his 65th birthday

References

[1] T.H.Etsell, S.N.Flengas: Chem. Rev.70 (3) (1970) 339.10.1021/cr60265a003Suche in Google Scholar

[2] G.Adachi, N.Imanaka, S.Tamura: Chem. Rev.102 (2002) 2405.10.1021/cr0103064Suche in Google Scholar

[3] T.Ishihara, H.Matsuda, Y.Takita: J. Am. Chem. Soc.116 (1994) 3801.10.1021/ja00088a016Suche in Google Scholar

[4] H.Näfe: Solid State Ionics13 (1983) 255.Suche in Google Scholar

[5] J.R.Macdonald: Impedance Spectroscopy emphasizing solid Materials and Systems, Wiley, New York (1987).Suche in Google Scholar

[6] A.K.Jonscher: J. Mater. Sci.13 (1978) 553.10.1007/BF00541805Suche in Google Scholar

[7] P.Abelard, J.F.Baumard: Phys. Rev. B16 (1981) 1005.Suche in Google Scholar

[8] K.V.Kale, K.M.Jadhav, G.K.Bichile: J. Mater. Sci. Lett.18 (1999) 9.10.1023/A:1006652705028Suche in Google Scholar

[9] Y.Madier, D.Descorme, A.M.Le Govic, D.Duprez: J. Phys. Chem. B103 (1999) 10999.10.1021/jp991270aSuche in Google Scholar

[10] M.Kilo, C.Argirusis, G.Borchardt, R.A.Jackson: Phys. Chem. Chem. Phys.5 (2003) 2219.10.1039/b300151mSuche in Google Scholar

[11] J.H.Strange: Cryst. Latt. Def. and Amorph. Mat.14 (1987) 183.Suche in Google Scholar

[12] P.Heitjans, S.Indris: J. Phys. Condens. Matter15 (2003) R1257.10.1088/0953-8984/15/30/202Suche in Google Scholar

[13] K.Fuda, K.Kishio, S.Yamauchi: J. Phys. Chem. Solids45 (1984) 1253.10.1016/0022-3697(84)90024-6Suche in Google Scholar

[14] K.Fuda, K.Kishio, S.Yamauchi: J. Phys. Chem. Solids46 (1985) 1141.10.1016/0022-3697(85)90142-8Suche in Google Scholar

[15] S.B.Adler, J.W.Smith, J.A.Reimer: J. Chem. Phys.98 (1993) 7613.10.1063/1.464701Suche in Google Scholar

[16] K.Fuda, K.Kishio, S.Yamauchi: Solid State Comm.53 (1985) 83.10.1016/0038-1098(85)90690-8Suche in Google Scholar

[17] P.S.Fiske, J.F.Stebbins, I.Farnan: Phys. Chem. Minerals20 (1994) 587.10.1007/BF00211854Suche in Google Scholar

[18] J.Emery, D.Massiot, P.Lacorre, Y.Laligant, K.Conder: Magn. Reson. Chem.43 (2005) 366.10.1002/mrc.1555Suche in Google Scholar

[19] N.Kim, R.-N.Vannier, C.P.Grey: Chem. Mater.17 (2005) 1952.10.1021/cm048388aSuche in Google Scholar

[20] N.Kim, C.P.Grey: Dalton Trans. (2004) 3048.10.1039/b402068pSuche in Google Scholar

[21] M.R.Hampson, J.S.O.Evans, P.Hodgkinson: J. Am. Chem. Soc.127 (2005) 15175.10.1021/ja054063zSuche in Google Scholar

[22] N.Kim, C.P.Grey: Science297 (2002) 1317.Suche in Google Scholar

[23] S.B.Adler, J.A.Reimer, J.Baltisberger, U.Werner: J. Am. Chem. Soc.116 (1994) 675.10.1021/ja00081a031Suche in Google Scholar

[24] Y.-M.Chiang, E.B.Lavik, I.Kosacki, H.L.Tuller: J. Electroceramics1 (1) (1997) 7.10.1023/A:1009958625841Suche in Google Scholar

[25] H.L.Tuller: Solid State Ionics131 (2000) 143.10.1016/S0167-2738(00)00629-9Suche in Google Scholar

[26] A.Tschöpe: Solid State Ionics139 (2001) 267.10.1016/S0167-2738(01)00677-4Suche in Google Scholar

[27] A.Tschöpe, E.Sommer, R.Birringer: Solid State Ionics139 (2001) 255.10.1016/S0167-2738(01)00678-6Suche in Google Scholar

[28] U.Brossmann, R.Würschum, K.Södervall, H.-E.Schaefer: J. Appl. Phys.85 (1999) 7646.10.1063/1.370567Suche in Google Scholar

[29] G.Knöner, K.Reimann, R.Röwer, K.Södervall, H.-E.Schaefer: PNAS100 (2003) 3870.10.1073/pnas.0730783100Suche in Google Scholar

[30] A.Szökefalvi-Nagy, H.D.Carstanjen, G.Knöner, F.Leis, H.-E.Schaefer, submitted.Suche in Google Scholar

[31] X.Guo, W.Sigle, J.Fleig, J.Maier: Solid State Ionics154–155 (2002) 555.10.1016/S0167-2738(02)00491-5Suche in Google Scholar

[32] S.Kim, J.Maier: J. Electrochem. Soc.149 (2002) J73.10.1149/1.1507597Suche in Google Scholar

[33] A.Bielecki, D.P.Burum: J. Magn. Reson. A116 (1995) 215.10.1006/jmra.1995.0010Suche in Google Scholar

[34] G.Neue, C.Dybowski: Solid StateNMR7 (1997) 333.Suche in Google Scholar

[35] T.J.Bastow, S.N.Stuart: Chem. Phys.143 (1990) 459.10.1016/0301-0104(90)87025-7Suche in Google Scholar

[36] N.Bloembergen, E.M.Purcell, R.V.Pound: Phys. Rev.73 (1948) 679.10.1103/PhysRev.73.679Suche in Google Scholar

Received: 2006-1-2
Accepted: 2006-2-15
Published Online: 2013-05-31
Published in Print: 2006-05-01

© 2006, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Editorial
  5. Basic
  6. Three-dimensional printing of TiAl3/Al2O3 composites
  7. Microemulsion mediated synthesis of nanocrystalline BaTiO3: possibilities, potential and perspectives
  8. Solid-State 17O NMR studies on Yttria-stabilized zirconia
  9. Twinning in ultrathin silicon nanowires
  10. Re-optimization of the Mg–Sb system under topological constraints
  11. Mg-rich phase equilibria of Mg–Mn–Zn alloys analyzed by computational thermochemistry
  12. The In–Pt–Sb phase diagram
  13. Thermodynamic evaluation of the Al–Cr–C system
  14. Thermodynamic description of the Ni–Si–Ti ternary system
  15. Enthalpies of formation measurements and thermodynamic description of the Ag–Cu–Zn system
  16. Thermodynamic assessment of the Mn–Cr–O system for solid oxide fuel cell (SOFC) materials
  17. Subsolidus phase equilibria in the CeO2−x–SiO2–ZrO2 system: An experimental study
  18. Generalized Maugis–Dugdale model of an elastic cylinder in non-slipping adhesive contact with a stretched substrate
  19. Implications of linear relationships between local and macroscopic flow stresses in the composite model
  20. Applied
  21. Gas-phase surface alloying under “kinetic control”: A novel approach to improving the surface properties of titanium alloys
  22. Thin film formation by oriented attachment of polymer-capped nanocrystalline ZnO
  23. The sintering mechanism and microstructure evolution in SiC–AlN ceramics studiedby EFTEM
  24. Thermal evolution of free volumes and of crystallization in amorphous Si–B–C–N ceramics
  25. High-temperature deformation behavior of nanocrystalline precursor-derived Si–B–C–N ceramics in controlled atmosphere
  26. Nanopowder dispersion and spray-drying process: the case of Cr2O3
  27. Electroless deposition of brushite (CaHPO4 · 2H2O) crystals on Ti–6Al–4V at room temperature
  28. The role of chemisorbed anions in the aqueous processing of AlN powder
  29. The influence of porosity on the electrical properties of liquid-phase sintered silicon carbide
  30. Development of high-temperature thermoelectric materials based on SrTiO3-layered perovskites
  31. The influence of the preparation method on the microstructure and properties of Al2O3/TiN nanocomposites
  32. Infrared properties of sintered α-MnSe
  33. Quasi-equilibrium sintering of particle clusters containing Bernal holes
  34. Design of metal ceramic composites
  35. Notifications
  36. DGM News
https://doi.org/10.3139/146.101265
Schlagwörter für diesen Artikel
17O NMR; Ionic conductors; Zirconia

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Editorial
  5. Basic
  6. Three-dimensional printing of TiAl3/Al2O3 composites
  7. Microemulsion mediated synthesis of nanocrystalline BaTiO3: possibilities, potential and perspectives
  8. Solid-State 17O NMR studies on Yttria-stabilized zirconia
  9. Twinning in ultrathin silicon nanowires
  10. Re-optimization of the Mg–Sb system under topological constraints
  11. Mg-rich phase equilibria of Mg–Mn–Zn alloys analyzed by computational thermochemistry
  12. The In–Pt–Sb phase diagram
  13. Thermodynamic evaluation of the Al–Cr–C system
  14. Thermodynamic description of the Ni–Si–Ti ternary system
  15. Enthalpies of formation measurements and thermodynamic description of the Ag–Cu–Zn system
  16. Thermodynamic assessment of the Mn–Cr–O system for solid oxide fuel cell (SOFC) materials
  17. Subsolidus phase equilibria in the CeO2−x–SiO2–ZrO2 system: An experimental study
  18. Generalized Maugis–Dugdale model of an elastic cylinder in non-slipping adhesive contact with a stretched substrate
  19. Implications of linear relationships between local and macroscopic flow stresses in the composite model
  20. Applied
  21. Gas-phase surface alloying under “kinetic control”: A novel approach to improving the surface properties of titanium alloys
  22. Thin film formation by oriented attachment of polymer-capped nanocrystalline ZnO
  23. The sintering mechanism and microstructure evolution in SiC–AlN ceramics studiedby EFTEM
  24. Thermal evolution of free volumes and of crystallization in amorphous Si–B–C–N ceramics
  25. High-temperature deformation behavior of nanocrystalline precursor-derived Si–B–C–N ceramics in controlled atmosphere
  26. Nanopowder dispersion and spray-drying process: the case of Cr2O3
  27. Electroless deposition of brushite (CaHPO4 · 2H2O) crystals on Ti–6Al–4V at room temperature
  28. The role of chemisorbed anions in the aqueous processing of AlN powder
  29. The influence of porosity on the electrical properties of liquid-phase sintered silicon carbide
  30. Development of high-temperature thermoelectric materials based on SrTiO3-layered perovskites
  31. The influence of the preparation method on the microstructure and properties of Al2O3/TiN nanocomposites
  32. Infrared properties of sintered α-MnSe
  33. Quasi-equilibrium sintering of particle clusters containing Bernal holes
  34. Design of metal ceramic composites
  35. Notifications
  36. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 30.9.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.101265/html
Button zum nach oben scrollen