Mechanical behaviour, microstructure and texture studies of wire arc additive manufactured 304L stainless steel
-
Minnam Reddy Suryanarayana Reddy
Abstract
Wire arc melting is considered one of the most efficient processes in additive manufacturing in terms of material printed to material consumed ratio. 304 stainless steel is one of the prominent stainless steels with superior corrosion resistance and mechanical properties. 304 stainless steel components were deposited by wire arc additive manufacturing, depositing subsequent layers in the same and perpendicular directions. Mechanical properties, microstructure, XRD and microtexture studies were done by EBSD have been done for both the conditions and compared. Mechanical properties were found to be similar for both the conditions whereas the microstructure and microtexture showed equiaxed grains for depositing in the same direction and columnar grains for deposition in the perpendicular direction.
-
Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Conflict of interest statement: The authors declare no conflicts of interest regarding this article.
-
Research funding: None declared.
References
1. Ziętala, M., Durejko, T., Polański, M., Kunce, I., Płociński, T., Zieliński, W., Łazińska, M., Stępniowski, W., Czujko, T., Kurzydłowski, K. J., Bojar, Z. The microstructure, mechanical properties and corrosion resistance of 316 L stainless steel fabricated using laser engineered net shaping. Mater. Sci. Eng. A 2016, 677, 1–10. https://doi.org/10.1016/J.MSEA.2016.09.028.Search in Google Scholar
2. Kurgan, N., Varol, R. Mechanical properties of P/M 316L stainless steel materials. Powder Technol. 2010, 201, 242–247. https://doi.org/10.1016/J.POWTEC.2010.03.041.Search in Google Scholar
3. Silvestru, V. A., Ariza, I., Vienne, J., Michel, L., Aguilar Sanchez, A. M., Angst, U., Rust, R., Gramazio, F., Kohler, M., Taras, A. Performance under tensile loading of point-by-point wire and arc additively manufactured steel bars for structural components. Mater. Des. 2021, 205, 109740. https://doi.org/10.1016/J.MATDES.2021.109740.Search in Google Scholar
4. Gardner, L., Kyvelou, P., Herbert, G., Buchanan, C. Testing and initial verification of the world’s first metal 3D printed bridge. J. Constr. Steel Res. 2020, 172, 106233. https://doi.org/10.1016/J.JCSR.2020.106233.Search in Google Scholar
5. Buchanan, C., Gardner, L. Metal 3D printing in construction: a review of methods, research, applications, opportunities and challenges. Eng. Struct. 2019, 180, 332–348. https://doi.org/10.1016/J.ENGSTRUCT.2018.11.045.Search in Google Scholar
6. Salman, O. O., Brenne, F., Niendorf, T., Eckert, J., Prashanth, K., Scudino, S. Impact of the scanning strategy on the mechanical behaviour of 316L steel synthesized by selective laser melting. J. Manuf. Process. 2019, 45, 255–261. https://doi.org/10.1016/J.JMAPRO.2019.07.010.Search in Google Scholar
7. Zhang, Y., Huang, W. Comparisons of 304 austenitic stainless steel manufactured by laser metal deposition and selective laser melting. J. Manuf. Process. 2020, 57, 324–333. https://doi.org/10.1016/J.JMAPRO.2020.06.042.Search in Google Scholar
8. Saeidi, K., Gao, X., Lofaj, F., Kvetková, L., Shen, Z. Transformation of austenite to duplex austenite-ferrite assembly in annealed stainless steel 316L consolidated by laser melting. J. Alloys Compd. 2015, 633, 463–469. https://doi.org/10.1016/J.JALLCOM.2015.01.249.Search in Google Scholar
9. Dezaki, M. L., Serjouei, A., Zolfagharian, A., Fotouhi, M., Moradi, M., Ariffin, M., Bodaghi, M. A review on additive/subtractive hybrid manufacturing of directed energy deposition (DED) process. Adv. Powder Mater. 2022, 1, 100054. https://doi.org/10.1016/J.APMATE.2022.100054.Search in Google Scholar
10. Hadjipantelis, N., Weber, B., Buchanan, C., Gardner, L. Description of the anisotropic material response of wire and arc additively manufactured thin-walled stainless steel elements. Thin-Walled Struct. 2022, 171, 108634. https://doi.org/10.1016/J.TWS.2021.108634.Search in Google Scholar
11. Lin, Z., Song, K., Yu, X. A review on wire and arc additive manufacturing of titanium alloy. J. Manuf. Process. 2021, 70, 24–45. https://doi.org/10.1016/J.JMAPRO.2021.08.018.Search in Google Scholar
12. Ma, G., Wu, S., Wang, R., Liu, D., Niu, F., Bi, G., Wu, D. Microstructure evaluation and resultant mechanical properties of laser- arc hybrid additive manufactured Cu–Cr–Zr alloy. J. Alloys Compd. 2022, 912, 165044. https://doi.org/10.1016/J.JALLCOM.2022.165044.Search in Google Scholar
13. Fang, X., Yang, J., Wang, S., Wang, C., Huang, K., Li, H., Lu, B. Additive manufacturing of high-performance AZ31 magnesium alloy with full equiaxed grains: microstructure, mechanical property, and electromechanical corrosion performance. J. Mater. Process. Technol. 2022, 300, 117430. https://doi.org/10.1016/J.JMATPROTEC.2021.117430.Search in Google Scholar
14. Chen, J., Wei, H., Zhang, X., Peng, Y., Kong, J., Wang, K. Flow behaviour and microstructure evolution during dynamic deformation of 316 L stainless steel fabricated by wire and arc additive manufacturing. Mater. Des. 2021, 198, 109325. https://doi.org/10.1016/J.MATDES.2020.109325.Search in Google Scholar
15. Wang, C., Liu, T. G., Zhu, P., Lu, Y., Shoji, T. Study on microstructure and tensile properties of 316L stainless steel fabricated by CMT wire and arc additive manufacturing. Mater. Sci. Eng. A 2020, 796, 140006. https://doi.org/10.1016/J.MSEA.2020.140006.Search in Google Scholar
16. Zhang, D., Liu, A., Yin, B., Wen, P. Additive manufacturing of duplex stainless steels – a critical review. J. Manuf. Process. 2022, 73, 496–517. https://doi.org/10.1016/J.JMAPRO.2021.11.036.Search in Google Scholar
17. Lopes, J. G., Machado, C. M., Duarte, V. R., Rodrigues, T. A., Santos, T. G., Oliveira, J. Effect of milling parameters on HSLA steel parts produced by wire and arc additive manufacturing (WAAM). J. Manuf. Process. 2020, 59, 739–749. https://doi.org/10.1016/J.JMAPRO.2020.10.007.Search in Google Scholar
18. Le, V. T., Mai, D. S., Doan, T. K., Paris, H. Wire and arc additive manufacturing of 308L stainless steel components: optimization of processing parameters and material properties. Eng. Sci. Technol. Int. J. 2021, 24, 1015–1026. https://doi.org/10.1016/J.JESTCH.2021.01.009.Search in Google Scholar
19. Li, M., Lu, T., Dai, J., Jia, X., Gu, X. Microstructure and mechanical properties of 308L stainless steel fabricated by laminar plasma additive manufacturing. Mater. Sci. Eng. A 2020, 770, 138523. https://doi.org/10.1016/J.MSEA.2019.138523.Search in Google Scholar
20. Haden, C. V., Zeng, G., Carter, F. M., Ruhl, C., Krick, B., Harlow, D. Wire and arc additive manufactured steel: tensile and wear properties. Addit. Manuf. 2017, 16, 115–123. https://doi.org/10.1016/J.ADDMA.2017.05.010.Search in Google Scholar
21. Caballero, A., Ding, J., Ganguly, S., Williams, S. Wire + arc additive manufacture of 17-4 PH stainless steel: effect of different processing conditions on microstructure, hardness, and tensile strength. J. Mater. Process. Technol. 2019, 268, 54–62. https://doi.org/10.1016/J.JMATPROTEC.2019.01.007.Search in Google Scholar
22. Wang, Z., Palmer, T. A., Beese, A. M. Effect of processing parameters on microstructure and tensile properties of austenitic stainless steel 304L made by directed energy deposition additive manufacturing. Acta Mater. 2016, 110, 226–235. https://doi.org/10.1016/J.ACTAMAT.2016.03.019.Search in Google Scholar
23. Gordon, J. V., Haden, C. V., Nied, H. F., Vinci, R., Harlow, D. Fatigue crack growth anisotropy, texture and residual stress in austenitic steel made by wire and arc additive manufacturing. Mater. Sci. Eng. A 2018, 724, 431–438. https://doi.org/10.1016/J.MSEA.2018.03.075.Search in Google Scholar
24. Zhang, S., Wang, Q., Yang, R., Dong, C. Composition equivalents of stainless steels understood via gamma stabilizing efficiency. Sci. Rep. 2021, 11, 5423. https://doi.org/10.1038/s41598-021-84917-z.Search in Google Scholar PubMed PubMed Central
25. Lee, D. J., Byun, J. C., Sung, J. H., Lee, H. W. The dependence of crack properties on the Cr/Ni equivalent ratio in AISI 304L austenitic stainless steel weld metals. Mater. Sci. Eng. A 2009, 513–514, 154–159. https://doi.org/10.1016/J.MSEA.2009.01.049.Search in Google Scholar
26. Zappa, S., Hoyos, J. J., Tufaro, L., Svoboda, H. In-situ X-ray diffraction analysis of reverted austenite in super martensitic stainless steel weld deposits. Forces Mech. 2022, 6, 100067. https://doi.org/10.1016/J.FINMEC.2021.100067.Search in Google Scholar
27. Wang, Q., Zhang, S., Zhang, C. H., Wu, C., Wang, J., Chen, J., Sun, Z. Microstructure evolution and EBSD analysis of graded steel fabricated by laser additive manufacturing. Vacuum 2017, 141, 68–81. https://doi.org/10.1016/J.VACUUM.2017.03.021.Search in Google Scholar
© 2023 Walter de Gruyter GmbH, Berlin/Boston
Articles in the same Issue
- Frontmatter
- Editorial
- Additive manufacturing and allied technologies
- Original Papers
- Influence of process parameters on ageing and free vibration characteristics of fiber-reinforced polymer composites by fusion filament fabrication process
- 3D biomimetic scaffold’s dimensional accuracy: a crucial geometrical response for bone tissue engineering
- Investigation of mechanical and microstructure properties of metal inert gas based wire arc additive manufactured Inconel 600 superalloy
- Study on the influence of surface roughness on tensile and low-cycle fatigue behavior of electron beam melted Ti‐6Al‐4V
- Effect of tool pin profile on the heat generation model of the friction stir welding of aluminium alloy
- Effect of clamping position on the residual stress in wire arc additive manufacturing
- Effect of welding speed on butt joint quality of laser powder bed fusion AlSi10Mg parts welded using Nd:YAG laser
- Mechanical behaviour, microstructure and texture studies of wire arc additive manufactured 304L stainless steel
- Evolution of microstructure and properties of CoCrFeMnNi high entropy alloy fabricated by selective laser melting
- Effect of laser energy density on surface morphology, microstructure and mechanical behaviour of direct metal laser melted 17-4 PH stainless steel
- The influence of rheology in the fabrication of ceramic-based scaffold for bone tissue engineering
- Behaviour of glass fiber reinforced polymer (GFRP) structural profile columns under axial compression
- Desirability function analysis approach for optimization of fused deposition modelling process parameters
- Effect of robotic weaving motion on mechanical and microstructural characteristics of wire arc additively manufactured NiTi shape memory alloy
- Rapid tooling of composite aluminium filled epoxy mould for injection moulding of polypropylene parts with small protruded features
- Investigation of microstructural evolution in a hybrid additively manufactured steel bead
- Fused filament fabricated PEEK based polymer composites for orthopaedic implants: a review
- Design of fixture for ultrasonic assisted gas tungsten arc welding using an integrated approach
- Effect of post-processing treatment on 3D-printed polylactic acid parts: layer interfaces and mechanical properties
- Investigating the effect of input parameters on tool wear in incremental sheet metal forming
- Microstructural evolution and improved corrosion resistance of NiCrSiFeB coatings prepared by laser cladding
- Microstructure and electrochemical behaviour of laser clad stainless steel 410 substrate with stainless steel 420 particles
- News
- DGM – Deutsche Gesellschaft für Materialkunde
Articles in the same Issue
- Frontmatter
- Editorial
- Additive manufacturing and allied technologies
- Original Papers
- Influence of process parameters on ageing and free vibration characteristics of fiber-reinforced polymer composites by fusion filament fabrication process
- 3D biomimetic scaffold’s dimensional accuracy: a crucial geometrical response for bone tissue engineering
- Investigation of mechanical and microstructure properties of metal inert gas based wire arc additive manufactured Inconel 600 superalloy
- Study on the influence of surface roughness on tensile and low-cycle fatigue behavior of electron beam melted Ti‐6Al‐4V
- Effect of tool pin profile on the heat generation model of the friction stir welding of aluminium alloy
- Effect of clamping position on the residual stress in wire arc additive manufacturing
- Effect of welding speed on butt joint quality of laser powder bed fusion AlSi10Mg parts welded using Nd:YAG laser
- Mechanical behaviour, microstructure and texture studies of wire arc additive manufactured 304L stainless steel
- Evolution of microstructure and properties of CoCrFeMnNi high entropy alloy fabricated by selective laser melting
- Effect of laser energy density on surface morphology, microstructure and mechanical behaviour of direct metal laser melted 17-4 PH stainless steel
- The influence of rheology in the fabrication of ceramic-based scaffold for bone tissue engineering
- Behaviour of glass fiber reinforced polymer (GFRP) structural profile columns under axial compression
- Desirability function analysis approach for optimization of fused deposition modelling process parameters
- Effect of robotic weaving motion on mechanical and microstructural characteristics of wire arc additively manufactured NiTi shape memory alloy
- Rapid tooling of composite aluminium filled epoxy mould for injection moulding of polypropylene parts with small protruded features
- Investigation of microstructural evolution in a hybrid additively manufactured steel bead
- Fused filament fabricated PEEK based polymer composites for orthopaedic implants: a review
- Design of fixture for ultrasonic assisted gas tungsten arc welding using an integrated approach
- Effect of post-processing treatment on 3D-printed polylactic acid parts: layer interfaces and mechanical properties
- Investigating the effect of input parameters on tool wear in incremental sheet metal forming
- Microstructural evolution and improved corrosion resistance of NiCrSiFeB coatings prepared by laser cladding
- Microstructure and electrochemical behaviour of laser clad stainless steel 410 substrate with stainless steel 420 particles
- News
- DGM – Deutsche Gesellschaft für Materialkunde