Effect of clamping position on the residual stress in wire arc additive manufacturing
-
Kumar Ujjwal
,
Mukul Anand
Abstract
The distortion of components printed by wire arc additive manufacturing (WAAM) due to repeated thermal cycles affects the build quality. The residual stress generated due to these thermal cycles can be predicted with the help of the finite element method. The temperature distribution and residual stresses in the WAAM component are predicted using a numerical model presented in this paper. Also, the effect of clamping position on the substrate is investigated. For this, two different clamping positions are compared with the unclamped state. The residual stress is minimum for the unclamped case and has maximum strain. The case where the substrate is clamped at the centre generates 77 % more tensile stress when compared with the corner clamped case.
-
Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Research funding: None declared.
-
Conflict of interest statement: The authors declare no conflicts of interest regarding this article.
References
1. Hauser, T., Reisch, R. T., Breese, P. P., Lutz, B. S., Pantano, M., Nalam, Y., Bela, K., Kamps, T., Volpp, J., Kaplan, A. F. H. Porosity in wire arc additive manufacturing of aluminium alloys. Addit. Manuf. 2021, 41, 101993. https://doi.org/10.1016/J.ADDMA.2021.101993.Search in Google Scholar
2. A. 52900:2015. Standard Terminology for Additive Manufacturing – General Principles – Terminology; ASTM International, 2015; pp 1–9. http://compass.astm.org/EDIT/html_annot.cgi?ISOASTM52900+15.Search in Google Scholar
3. Yuan, L., Pan, Z., Ding, D., He, F., van Duin, S., Li, H., Li, W. Investigation of humping phenomenon for the multi-directional robotic wire and arc additive manufacturing. Robot. Comput. Integr. Manuf. 2020, 63, 101916. https://doi.org/10.1016/j.rcim.2019.101916.Search in Google Scholar
4. Ding, D., Pan, Z., Cuiuri, D., Li, H. A multi-bead overlapping model for robotic wire and arc additive manufacturing (WAAM). Robot. Comput. Integr. Manuf. 2015, 31, 101–110. https://doi.org/10.1016/j.rcim.2014.08.008.Search in Google Scholar
5. Radel, S., Diourte, A., Soulié, F., Company, O., Bordreuil, C. Skeleton arc additive manufacturing with closed loop control. Addit. Manuf. 2019, 26, 106–116. https://doi.org/10.1016/j.addma.2019.01.003.Search in Google Scholar
6. Klein, T., Schnall, M. Control of macro-/microstructure and mechanical properties of a wire-arc additive manufactured aluminum alloy. Int. J. Adv. Des. Manuf. Technol. 2020, 108, 235–244. https://doi.org/10.1007/s00170-020-05396-6.Search in Google Scholar
7. Singh, R., Raj, B., Mudali, U. K., Singh, P. Non-destructive Evaluation of Corrosion and Corrosion-Assisted Cracking; John Wiley & Sons: Westerville, 2019.10.1002/9781118987735Search in Google Scholar
8. Abusalma, H., Eisazadeh, H., Hejripour, F., Bunn, J., Aidun, D. K. Parametric study of residual stress formation in wire and arc additive manufacturing. J. Manuf. Process. 2022, 75, 863–876. https://doi.org/10.1016/j.jmapro.2022.01.043.Search in Google Scholar
9. Fan, D., Gao, M., Li, C., Huang, J., Yu, X. Residual stress and microstructure properties by trailing cooling of argon gas of wire and arc additive manufacturing. J. Manuf. Process. 2022, 77, 32–39. https://doi.org/10.1016/j.jmapro.2022.03.007.Search in Google Scholar
10. Shen, H., Lin, J., Zhou, Z., Liu, B. Effect of induction heat treatment on residual stress distribution of components fabricated by wire arc additive manufacturing. J. Manuf. Process. 2022, 75, 331–345. https://doi.org/10.1016/j.jmapro.2022.01.018.Search in Google Scholar
11. Li, F., Chen, S., Shi, J., Zhao, Y. In-process control of distortion in wire and arc additive manufacturing based on a flexible multi-point support fixture. Sci. Technol. Weld. Joining 2019, 24, 36–42. https://doi.org/10.1080/13621718.2018.1476083.Search in Google Scholar
12. Goldak, J., Chakravarti, A., Bibby, M. A new finite element model for welding heat sources. Metall. Trans. B 1984, 15, 299–305. https://doi.org/10.1007/bf02667333.Search in Google Scholar
13. Montevecchi, F., Venturini, G., Grossi, N., Scippa, A., Campatelli, G. Idle time selection for wire-arc additive manufacturing: a finite element-based technique. Addit. Manuf. 2018, 21, 479–486. https://doi.org/10.1016/j.addma.2018.01.007.Search in Google Scholar
14. Montevecchi, F., Venturini, G., Grossi, N., Scippa, A., Campatelli, G. Finite element mesh coarsening for effective distortion prediction in wire arc additive manufacturing. Addit. Manuf. 2017, 18, 145–155. https://doi.org/10.1016/j.addma.2017.10.010.Search in Google Scholar
15. Srivastava, S., Kumar, R., Vishal, G., Anish, S. S., Pam, D. W. F. Measurement and mitigation of residual stress in wire – arc Additive manufacturing: a review of macro – scale continuum modelling approach. Arch. Comput. Methods Eng. 2020, 28, 3491–3515. https://doi.org/10.1007/s11831-020-09511-4.Search in Google Scholar
16. Valencia, J. J., Quested, P. N. Thermophysical Properties; ASM International: Geauga county, 2013.Search in Google Scholar
17. Montevecchi, F., Venturini, G., Scippa, A., Campatelli, G. Finite element modelling of wire-arc-additive-manufacturing process. Procedia CIRP 2016, 55, 109–114. https://doi.org/10.1016/j.procir.2016.08.024.Search in Google Scholar
© 2023 Walter de Gruyter GmbH, Berlin/Boston
Articles in the same Issue
- Frontmatter
- Editorial
- Additive manufacturing and allied technologies
- Original Papers
- Influence of process parameters on ageing and free vibration characteristics of fiber-reinforced polymer composites by fusion filament fabrication process
- 3D biomimetic scaffold’s dimensional accuracy: a crucial geometrical response for bone tissue engineering
- Investigation of mechanical and microstructure properties of metal inert gas based wire arc additive manufactured Inconel 600 superalloy
- Study on the influence of surface roughness on tensile and low-cycle fatigue behavior of electron beam melted Ti‐6Al‐4V
- Effect of tool pin profile on the heat generation model of the friction stir welding of aluminium alloy
- Effect of clamping position on the residual stress in wire arc additive manufacturing
- Effect of welding speed on butt joint quality of laser powder bed fusion AlSi10Mg parts welded using Nd:YAG laser
- Mechanical behaviour, microstructure and texture studies of wire arc additive manufactured 304L stainless steel
- Evolution of microstructure and properties of CoCrFeMnNi high entropy alloy fabricated by selective laser melting
- Effect of laser energy density on surface morphology, microstructure and mechanical behaviour of direct metal laser melted 17-4 PH stainless steel
- The influence of rheology in the fabrication of ceramic-based scaffold for bone tissue engineering
- Behaviour of glass fiber reinforced polymer (GFRP) structural profile columns under axial compression
- Desirability function analysis approach for optimization of fused deposition modelling process parameters
- Effect of robotic weaving motion on mechanical and microstructural characteristics of wire arc additively manufactured NiTi shape memory alloy
- Rapid tooling of composite aluminium filled epoxy mould for injection moulding of polypropylene parts with small protruded features
- Investigation of microstructural evolution in a hybrid additively manufactured steel bead
- Fused filament fabricated PEEK based polymer composites for orthopaedic implants: a review
- Design of fixture for ultrasonic assisted gas tungsten arc welding using an integrated approach
- Effect of post-processing treatment on 3D-printed polylactic acid parts: layer interfaces and mechanical properties
- Investigating the effect of input parameters on tool wear in incremental sheet metal forming
- Microstructural evolution and improved corrosion resistance of NiCrSiFeB coatings prepared by laser cladding
- Microstructure and electrochemical behaviour of laser clad stainless steel 410 substrate with stainless steel 420 particles
- News
- DGM – Deutsche Gesellschaft für Materialkunde
Articles in the same Issue
- Frontmatter
- Editorial
- Additive manufacturing and allied technologies
- Original Papers
- Influence of process parameters on ageing and free vibration characteristics of fiber-reinforced polymer composites by fusion filament fabrication process
- 3D biomimetic scaffold’s dimensional accuracy: a crucial geometrical response for bone tissue engineering
- Investigation of mechanical and microstructure properties of metal inert gas based wire arc additive manufactured Inconel 600 superalloy
- Study on the influence of surface roughness on tensile and low-cycle fatigue behavior of electron beam melted Ti‐6Al‐4V
- Effect of tool pin profile on the heat generation model of the friction stir welding of aluminium alloy
- Effect of clamping position on the residual stress in wire arc additive manufacturing
- Effect of welding speed on butt joint quality of laser powder bed fusion AlSi10Mg parts welded using Nd:YAG laser
- Mechanical behaviour, microstructure and texture studies of wire arc additive manufactured 304L stainless steel
- Evolution of microstructure and properties of CoCrFeMnNi high entropy alloy fabricated by selective laser melting
- Effect of laser energy density on surface morphology, microstructure and mechanical behaviour of direct metal laser melted 17-4 PH stainless steel
- The influence of rheology in the fabrication of ceramic-based scaffold for bone tissue engineering
- Behaviour of glass fiber reinforced polymer (GFRP) structural profile columns under axial compression
- Desirability function analysis approach for optimization of fused deposition modelling process parameters
- Effect of robotic weaving motion on mechanical and microstructural characteristics of wire arc additively manufactured NiTi shape memory alloy
- Rapid tooling of composite aluminium filled epoxy mould for injection moulding of polypropylene parts with small protruded features
- Investigation of microstructural evolution in a hybrid additively manufactured steel bead
- Fused filament fabricated PEEK based polymer composites for orthopaedic implants: a review
- Design of fixture for ultrasonic assisted gas tungsten arc welding using an integrated approach
- Effect of post-processing treatment on 3D-printed polylactic acid parts: layer interfaces and mechanical properties
- Investigating the effect of input parameters on tool wear in incremental sheet metal forming
- Microstructural evolution and improved corrosion resistance of NiCrSiFeB coatings prepared by laser cladding
- Microstructure and electrochemical behaviour of laser clad stainless steel 410 substrate with stainless steel 420 particles
- News
- DGM – Deutsche Gesellschaft für Materialkunde
