Influence of process parameters on ageing and free vibration characteristics of fiber-reinforced polymer composites by fusion filament fabrication process
-
Abstract
Fused filament fabrication is a promising additive manufacturing technology and an alternative to traditional processes for the fabrication of polymer and fiber-reinforced polymer composites. In this work, the effects of process parameters such as layer thickness, infill density, and infill pattern on the ageing and free vibration characteristics of three-dimensional printed composites were investigated. It was observed that the water absorption rate is higher in acrylonitrile butadiene styrene (ABS) printed specimens compared to carbon fiber reinforced acrylonitrile butadiene styrene (CF/ABS) specimens due to the effect of carbon fiber which acts as a strong hydrophobic material. The free vibration characteristic of the printed composite specimen is found as per American Society for Testing Materials standards. From the results, it is found that the 5 % addition of carbon fiber, hexagonal pattern, and 0.30 mm layer thickness show an increase in the vibration behaviour of the composites compared to the specimen printed without reinforcement. Experimental modal analysis was carried out on a cantilever beam-like sample and revealed that the addition of fiber has enhanced natural frequencies and damping ratio.
-
Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Conflict of interest statement: The authors declare no conflicts of interest regarding this article.
-
Research funding: None declared.
References
1. Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., Hui, D. Composites, Part B 2018, 143, 172. https://doi.org/10.1016/j.compositesb.2018.02.012.Suche in Google Scholar
2. Krajangsawasdi, N., Blok, L. G., Hamerton, I., Longana, M. L., Woods, B. K. S., Ivanov, D. S. J. Compos. Sci. 2021, 5, 29. https://doi.org/10.3390/jcs5010029.Suche in Google Scholar
3. Leite, M., Varanda, A., Ribeoro, A. R., Silva, A., Viz, M. F. Rapid Prototyp. J. 2018, 24, 195. https://doi.org/10.1108/RPJ-04-2016-0057.Suche in Google Scholar
4. Ecker, J. V., Haider, A., Burzic, I., Huber, A., Eder, G., Hild, S. Rapid Prototyp. J. 2019, 25, 672. https://doi.org/10.1108/RPJ-06-2018- 0149.10.1108/RPJ-06-2018-0149Suche in Google Scholar
5. Kesentini, Z., Mahi, A. E., Rebiere, J. L., Guerjouma, R. E., Beyaoui, M., Haddar, M. Polym. Polym. Compos. 2022, 25, 1–11.Suche in Google Scholar
6. Ravikumar, P., Rajeshkumar, G., Maran, J. P., Al- Dhabi, N. A., Karuppiah, P. J. Nat. Fibers 2021, 6521–6533. https://doi.org/10.1080/15440478.2021.1924339.Suche in Google Scholar
7. Wang, R., Shang, J., Li, X., Luo, Z., Wu, W. Sci. Rep. 2018, 8, 9604. https://doi.org/10.1038/s41598-018-27963-4.Suche in Google Scholar PubMed PubMed Central
8. Chaitnya, S. K., Reddy, K. M., Harsh, S. N. S. C. Int. J. Innov. Res. Technol. Sci. Eng. 2015, 4, 4601. https://doi.org/10.15680/IJIRSET.2015.0406087.Suche in Google Scholar
9. Kannan, S., Ramamoorthy, M. Mater. Res. Express 2020, 7, 015341. https://doi.org/10.1088/2053-1591/ab6a48.Suche in Google Scholar
10. Ayrilmis, N., Kariz, M., Kwon, J. H., Kuzman, M. K. Int. J. Adv. Manuf. Technol. 2019, 102, 2195. https://doi.org/10.1007/s00170-019-03299- 99.10.1007/s00170-019-03299-9Suche in Google Scholar
11. Yadav, P. K., Abhishek, Singh, K., Bhaskar, J. Advances in Manufacturing and Industrial Engineering; Elsevier Publications: Singapore, 2021.Suche in Google Scholar
12. Porter, J. H., Cain, T. M., Fox, S. L., Harvey, P. S. Virtual Phys. Prototyping 2019, 14, 148. https://doi.org/10.1080/17452759.2018.1537064.Suche in Google Scholar
13. Maloch, J., Hnatkova, E., Zaludek, M., Kratky, P. Mater. Sci. Forum 2018, 919, 230. https://doi.org/10.4028/www.scientific.net/msf.919.230.Suche in Google Scholar
14. Priya, M. S., Naresh, K., Jayaganthan, R., Velmurugan, R. Mater. Res. Express 2019, 6, 085345. https://doi.org/10.1088/2053-1591/ab2776.Suche in Google Scholar
15. Ilangovan, S., Kumaran, S. S., Naresh, K. Mater. Res. Express 2020, 7, 025007. https://doi.org/10.1088/2053-1591/ab6e36.Suche in Google Scholar
16. Vigneshwaran, K., Venkateshwaran, N. Int. J. Polym. Anal. Charact. 2019, 24, 584. https://doi.org/10.1080/1023666X.2019.1630940.Suche in Google Scholar
17. Naveed, N. Mater. Technol. 2020, 36, 317. https://doi.org/10.1080/10667857.2020.1758475.Suche in Google Scholar
18. Aloyaydi, B. A., Sivasankaran, S. Trans. Indian Inst. Met. 2020, 73, 1669. https://doi.org/10.1007/s12666-020-01952-6.Suche in Google Scholar
19. Senthilrajan, S., Venkateshwaran, N., Naresh, K. J. Nat. Fibers 2022, 13063–13075. https://doi.org/10.1080/15440478.2022.2085225.Suche in Google Scholar
20. Huang, J., Huang, Z., Du, H., Zhang, J. Trans. Indian Inst. Met. 2020, 75, 1403. https://doi.org/10.1007/s12666-021-02487-0.Suche in Google Scholar
© 2023 Walter de Gruyter GmbH, Berlin/Boston
Artikel in diesem Heft
- Frontmatter
- Editorial
- Additive manufacturing and allied technologies
- Original Papers
- Influence of process parameters on ageing and free vibration characteristics of fiber-reinforced polymer composites by fusion filament fabrication process
- 3D biomimetic scaffold’s dimensional accuracy: a crucial geometrical response for bone tissue engineering
- Investigation of mechanical and microstructure properties of metal inert gas based wire arc additive manufactured Inconel 600 superalloy
- Study on the influence of surface roughness on tensile and low-cycle fatigue behavior of electron beam melted Ti‐6Al‐4V
- Effect of tool pin profile on the heat generation model of the friction stir welding of aluminium alloy
- Effect of clamping position on the residual stress in wire arc additive manufacturing
- Effect of welding speed on butt joint quality of laser powder bed fusion AlSi10Mg parts welded using Nd:YAG laser
- Mechanical behaviour, microstructure and texture studies of wire arc additive manufactured 304L stainless steel
- Evolution of microstructure and properties of CoCrFeMnNi high entropy alloy fabricated by selective laser melting
- Effect of laser energy density on surface morphology, microstructure and mechanical behaviour of direct metal laser melted 17-4 PH stainless steel
- The influence of rheology in the fabrication of ceramic-based scaffold for bone tissue engineering
- Behaviour of glass fiber reinforced polymer (GFRP) structural profile columns under axial compression
- Desirability function analysis approach for optimization of fused deposition modelling process parameters
- Effect of robotic weaving motion on mechanical and microstructural characteristics of wire arc additively manufactured NiTi shape memory alloy
- Rapid tooling of composite aluminium filled epoxy mould for injection moulding of polypropylene parts with small protruded features
- Investigation of microstructural evolution in a hybrid additively manufactured steel bead
- Fused filament fabricated PEEK based polymer composites for orthopaedic implants: a review
- Design of fixture for ultrasonic assisted gas tungsten arc welding using an integrated approach
- Effect of post-processing treatment on 3D-printed polylactic acid parts: layer interfaces and mechanical properties
- Investigating the effect of input parameters on tool wear in incremental sheet metal forming
- Microstructural evolution and improved corrosion resistance of NiCrSiFeB coatings prepared by laser cladding
- Microstructure and electrochemical behaviour of laser clad stainless steel 410 substrate with stainless steel 420 particles
- News
- DGM – Deutsche Gesellschaft für Materialkunde
Artikel in diesem Heft
- Frontmatter
- Editorial
- Additive manufacturing and allied technologies
- Original Papers
- Influence of process parameters on ageing and free vibration characteristics of fiber-reinforced polymer composites by fusion filament fabrication process
- 3D biomimetic scaffold’s dimensional accuracy: a crucial geometrical response for bone tissue engineering
- Investigation of mechanical and microstructure properties of metal inert gas based wire arc additive manufactured Inconel 600 superalloy
- Study on the influence of surface roughness on tensile and low-cycle fatigue behavior of electron beam melted Ti‐6Al‐4V
- Effect of tool pin profile on the heat generation model of the friction stir welding of aluminium alloy
- Effect of clamping position on the residual stress in wire arc additive manufacturing
- Effect of welding speed on butt joint quality of laser powder bed fusion AlSi10Mg parts welded using Nd:YAG laser
- Mechanical behaviour, microstructure and texture studies of wire arc additive manufactured 304L stainless steel
- Evolution of microstructure and properties of CoCrFeMnNi high entropy alloy fabricated by selective laser melting
- Effect of laser energy density on surface morphology, microstructure and mechanical behaviour of direct metal laser melted 17-4 PH stainless steel
- The influence of rheology in the fabrication of ceramic-based scaffold for bone tissue engineering
- Behaviour of glass fiber reinforced polymer (GFRP) structural profile columns under axial compression
- Desirability function analysis approach for optimization of fused deposition modelling process parameters
- Effect of robotic weaving motion on mechanical and microstructural characteristics of wire arc additively manufactured NiTi shape memory alloy
- Rapid tooling of composite aluminium filled epoxy mould for injection moulding of polypropylene parts with small protruded features
- Investigation of microstructural evolution in a hybrid additively manufactured steel bead
- Fused filament fabricated PEEK based polymer composites for orthopaedic implants: a review
- Design of fixture for ultrasonic assisted gas tungsten arc welding using an integrated approach
- Effect of post-processing treatment on 3D-printed polylactic acid parts: layer interfaces and mechanical properties
- Investigating the effect of input parameters on tool wear in incremental sheet metal forming
- Microstructural evolution and improved corrosion resistance of NiCrSiFeB coatings prepared by laser cladding
- Microstructure and electrochemical behaviour of laser clad stainless steel 410 substrate with stainless steel 420 particles
- News
- DGM – Deutsche Gesellschaft für Materialkunde
