Surfactant assisted single step electrodeposition of CuInSe2 thin films with rich indium selenide surface over layer
-
Priti Singh
,
Pundrikaksha Upadhyay
Abstract
In this work, we report on the electrodeposition of CuInSe2 (CIS) thin films with In2Se3 rich surface by a single step deposition technique. It was observed that the In-content deposited in CIS can be improved by the addition of sodium dodecyl sulfate as a surfactant. The presence of an In–Se rich layer was confirmed by electrochemical, compositional and Raman spectroscopy analysis. The photo-electrochemical properties of the as-deposited CuInSe2 thin films were found to be enhanced due to the presence of In–Se rich superficial layer. The presence of an In–Se layer over CIS may act as a p-n homo-junction which may be attributed as the primary reason for the improvement in the PEC properties.
-
Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Research funding: None declared.
-
Conflict of interest statement: The authors declare no conflicts of interest regarding this article.
References
1. Kodigala, S. R. Cu (In1–xGax)Se2 and CuIn(Se1–xSx)2 thin film solar cells. In Thin films and nanostructures; Academic Press, Vol. XXXV, 2010; pp. 505–679.10.1016/B978-0-12-373697-0.00008-0Suche in Google Scholar
2. Kampmann, A., Sittinger, V., Rechid, J., Reineke-Koch, R. Thin Solid Films 2000, 361, 309–313. https://doi.org/10.1016/S0040-6090(99)00863-9.Suche in Google Scholar
3. Kapur, V. K., Bansal, A., Le, P., Asensio, O. I. Thin Solid Films 2003, 53, 431. https://doi.org/10.1016/S0040-6090(03)00253-0.Suche in Google Scholar
4. Chandran, R., Panda, S. K., Mallik, A. Mater. Renew. Sustain. Energy 2018, 7, 6. https://doi.org/10.1007/s40243-018-0112-1.Suche in Google Scholar
5. Faraj, M. G., Ibrahim, K., Salhin, A. Mater. Sci. Semicond. Process. 2012, 15, 206–213. https://doi.org/10.1016/j.mssp.2011.10.006.Suche in Google Scholar
6. Luo, P., Zhu, C., Jiang, G. Solid State Commun. 2008, 146, 57. https://doi.org/10.1016/j.ssc.2008.01.020.Suche in Google Scholar
7. Guillen, C., Herrero, J. Vacuum 2002, 67, 659. https://doi.org/10.1016/S0042-207X(02)00258-0Get.Suche in Google Scholar
8. Calixto, M. E., Dobson, K. D., McCandless, B. E., Birkmire, R. W. J. Electrochem. Soc. 2006, 153, G521. https://doi.org/10.1149/1.2186764.Suche in Google Scholar
9. Hibberd, C. J., Chassaing, E., Liu, W., Mitzi, D. B., Lincot, D., Tiwari, A. N. Prog. Photovolt. 2010, 18, 434–452. https://doi.org/10.1002/pip.914.Suche in Google Scholar
10. Bertram, T., Depredurand, V., Siebentritt, S. 2014 IEEE 40th Photovoltaic Specialist Conference, PVSC, 2014; pp. 3633–3636.10.1109/PVSC.2014.6924894Suche in Google Scholar
11. Aida, Y., Depredurand, V., Larsen, J. K., Arai, H., Tanaka, D., Kurihara, M., Siebentritt, S. Prog. Photovolt. 2015, 23, 754–764. https://doi.org/10.1002/pip.2493.Suche in Google Scholar
12. Kwon, S. H., Park, S. C., Ahn, B. T., Yoon, K. H., Song, J. Sol. Energy 1998, 64, 55–60. https://doi.org/10.1016/S0038-092X(98)00024-3.Suche in Google Scholar
13. Lee, D. Y., Yun, J. H., Yoon, K. H., Ahn, B. T. Thin Solid Films 2002, 410, 171–176. https://doi.org/10.1016/S0040-6090(02)00249-3.Suche in Google Scholar
14. Li, X., Liu, W., Jiang, G., Wang, D., Zhu, C. Mater. Lett. 2012, 70, 116–118. https://doi.org/10.1016/j.matlet.2011.11.110.Suche in Google Scholar
15. Friedlmeier, T. M., Jackson, P., Bauer, A., Hariskos, D., Kiowski, O., Menner, R., Wuerz, R., Powalla, M. Thin Solid Films 2017, 633, 13–17. https://doi.org/10.1016/j.tsf.2016.08.021.Suche in Google Scholar
© 2023 Walter de Gruyter GmbH, Berlin/Boston
Artikel in diesem Heft
- Frontmatter
- Editorial
- Editorial ICPCM 2021
- Original Papers
- Developing easy-to-use, cost-effective wound dressing material by coating commercial cotton bandages with nanomaterials
- Temperature and magnetic field controlled dielectric relaxation and magnetodielectric response in KBiFe1.9Co0.1O5 polycrystalline
- Influence of thermo-mechanical treatment in austenitic and ferritic field condition on microstructural and mechanical properties of reduced activation ferritic-martensitic steel
- Effect of nanoparticle on mechanical properties of activated tungsten gas welding of austenite stainless steel 316L and optimization of process parameters
- Flexural behavior of carbon/glass inter-ply hybrid FRP composites under elevated temperature environments
- Surfactant assisted single step electrodeposition of CuInSe2 thin films with rich indium selenide surface over layer
- Optimization of hot rolling parameters of CRNO steel with the aid of hot compression test and deformation map
- Reduced graphene oxide synthesis by dry planetary ball milling followed by arc plasma treatment of high pure graphite
- Influence of interphase characteristics on the elastic modulus of unidirectional glass-reinforced epoxy composites: a computational micromechanics study
- Investigation of dielectric, impedance, and magnetodielectric behavior in Bi5Ti3FeO15–Bi2Fe4O9 composites prepared by sol–gel modified method
- Effect of spheroidization annealing on low cycle fatigue (LCF) characteristics of cold forged steel components
- Growth of CuO nanoparticles using one step chemical bath deposition under microwave heating and their characterizations
- Phase formation and electrical properties study of PVDF thick films synthesized by solution casting method
- Generation of microchannels on PMMA using an in-house fabricated μ-ECDM system
- Temperature dependent constitutive plastic flow behaviour of titanium alloy Ti6Al4V
- Production and characterization of Al–Cu binary alloy produced by using novel continuous casting process
- Synthesis of Al–Sn alloys by direct chill casting under the effect of mechanical stirring: an experimental and simulation optimization study
- Evaluation of characteristics for microwave-assisted polymer coating of the steel substrate
- Synthesis and fabrication of acrylic acid treated rattan fiber epoxy composite
- Development of superhydrophobic hybrid silica-cellulose aerogel as promising thermal insulation and sound absorption
- Effect of thermal annealing on structure and magnetic properties in a Ni–Cr multilayer
- Effect of heat input on corrosion behavior of automotive zinc-coated steel joint
- Development of Al–SiC–TiO2 hybrid composite using powder metallurgy route and the influence of TiO2 content variation on microstructure and mechanical properties
- News
- DGM – Deutsche Gesellschaft für Materialkunde
Artikel in diesem Heft
- Frontmatter
- Editorial
- Editorial ICPCM 2021
- Original Papers
- Developing easy-to-use, cost-effective wound dressing material by coating commercial cotton bandages with nanomaterials
- Temperature and magnetic field controlled dielectric relaxation and magnetodielectric response in KBiFe1.9Co0.1O5 polycrystalline
- Influence of thermo-mechanical treatment in austenitic and ferritic field condition on microstructural and mechanical properties of reduced activation ferritic-martensitic steel
- Effect of nanoparticle on mechanical properties of activated tungsten gas welding of austenite stainless steel 316L and optimization of process parameters
- Flexural behavior of carbon/glass inter-ply hybrid FRP composites under elevated temperature environments
- Surfactant assisted single step electrodeposition of CuInSe2 thin films with rich indium selenide surface over layer
- Optimization of hot rolling parameters of CRNO steel with the aid of hot compression test and deformation map
- Reduced graphene oxide synthesis by dry planetary ball milling followed by arc plasma treatment of high pure graphite
- Influence of interphase characteristics on the elastic modulus of unidirectional glass-reinforced epoxy composites: a computational micromechanics study
- Investigation of dielectric, impedance, and magnetodielectric behavior in Bi5Ti3FeO15–Bi2Fe4O9 composites prepared by sol–gel modified method
- Effect of spheroidization annealing on low cycle fatigue (LCF) characteristics of cold forged steel components
- Growth of CuO nanoparticles using one step chemical bath deposition under microwave heating and their characterizations
- Phase formation and electrical properties study of PVDF thick films synthesized by solution casting method
- Generation of microchannels on PMMA using an in-house fabricated μ-ECDM system
- Temperature dependent constitutive plastic flow behaviour of titanium alloy Ti6Al4V
- Production and characterization of Al–Cu binary alloy produced by using novel continuous casting process
- Synthesis of Al–Sn alloys by direct chill casting under the effect of mechanical stirring: an experimental and simulation optimization study
- Evaluation of characteristics for microwave-assisted polymer coating of the steel substrate
- Synthesis and fabrication of acrylic acid treated rattan fiber epoxy composite
- Development of superhydrophobic hybrid silica-cellulose aerogel as promising thermal insulation and sound absorption
- Effect of thermal annealing on structure and magnetic properties in a Ni–Cr multilayer
- Effect of heat input on corrosion behavior of automotive zinc-coated steel joint
- Development of Al–SiC–TiO2 hybrid composite using powder metallurgy route and the influence of TiO2 content variation on microstructure and mechanical properties
- News
- DGM – Deutsche Gesellschaft für Materialkunde
