Startseite Investigation into the kinetic behavior of molten aluminum pressureless infiltration into SiC preforms
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Investigation into the kinetic behavior of molten aluminum pressureless infiltration into SiC preforms

  • Hassan Sharifi und Mohamad Reza Nasresfahani
Veröffentlicht/Copyright: 29. September 2016
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 107 Heft 10

Abstract

Infiltration of molten metal into ceramic performs without using external force is a new fabrication method for metal-matrix composites. In this research, the kinetics of pressureless infiltration in the processing of Al/SiC composites have been investigated. In order to improve the wettability and infiltration properties, Al-6Mg (wt.%) alloy was prepared. Also, the ceramic component was coated for 15 min using electroless copper plating at a temperature of 60 – 70 °C (pH = 12.5) and a rate of 17 – 20 μm s−1. Infiltration of molten aluminum into the coated ceramic perform was successfully carried out in the temperature range of 850 to 950 °C under nitrogen atmosphere. Microstructural investigations indicated a well-bonded metal–ceramic joint. Kinetic studies showed that the melt infiltration into the ceramic foam follows an S-shaped curve. The infiltration rate was specified with respect to variables such as the experiment temperature and the size of the pores of the ceramic component. The results revealed that by increasing the temperature and the size of pores, the infiltration rate increases. For infiltrating molten metal into the 10 and 30 ppi foams, activation energies of 5.902 kJ mol−1 and 7.232 kJ mol−1 are required, respectively.

Keywords: Aluminum composite; SiC; Pressureless infiltration; Preform
*Correspondence address, Hassan Sharifi, Department of Materials Science, Faculty of Engineering, University of Shahrekord, Shahrekord, Iran, Tel.: +989131094053, Fax: +983832324401, E-mail:

References

[1] K.U.Kainer: Metal Matrix Composites, Custom-made materials for automotive and aerospace engineering, 1st Ed., Wiley-VCH, Weinheim, Germany (2003).Suche in Google Scholar

[2] J.Eliasson, R.Sandström: Key Eng. Mater.104 (1995) 3. 10.4028/www.scientific.net/KEM.104-107.3Suche in Google Scholar

[3] S.-R.Wang, H.-R.Gang, Y.-Z.Wang: J. Mater. Sci.41 (2006) 5751. 10.1007/s10853-006-0106-8Suche in Google Scholar

[4] J.W.Kaczmar, K.Pietrzak, W.Wlosinski: J. Mater. Process. Technol.106 (2000) 58. 10.1016/S0924-0136(00)00639-7Suche in Google Scholar

[5] S.Vaucher, J.Kuebler, O.Beffort, L.Biasetto, F.Zordan, P.Colombo: Compos. Sci. Technol.68 (2008) 3202. 10.1016/j.compscitech.2008.08.004Suche in Google Scholar

[6] M.Mizumoto, T.Ohgai, A.Kagawa: J. Mater. Sci. Eng. A413 (2005) 521. 10.1016/j.msea.2005.07.065Suche in Google Scholar

[7] E.Akbarzadeh, A.P.Josep, M.Picas, B.Teresa: Mater. Des.88 (2015) 683. 10.1016/j.matdes.2015.09.015Suche in Google Scholar

[8] S.Ren, X.Qu, X.He, M.Qin, X.Shen: J. Alloys Compd.484 (2009) 256. 10.1016/j.jallcom.2009.04.074Suche in Google Scholar

[9] J.Liu, Z.Zheng, J.Wang: J. Alloys Compd.465 (2007) 239. 10.1016/j.jallcom.2007.10.055Suche in Google Scholar

[10] G.Kraub, J.Kübler, E.Trentini: J. Mater. Sci. Eng. A337 (2002) 315. 10.1016/S0921-5093(02)00044-8Suche in Google Scholar

[11] S.N.Chou, J.L.Huang, D.F.Lii, H.H.Lu: J. Alloys Compd.419 (2006) 98–102. 10.1016/j.jallcom.2005.10.006Suche in Google Scholar

[12] A.Demir, N.Altinkok: Compos. Sci. Technol.64 (2004) 2067. 10.1016/j.compscitech.2004.02.015Suche in Google Scholar

[13] E.Carreno-Marelli, T.Cutard, R.Schaller, C.Bonjour: J. Mater. Sci. Eng. A251 (1998) 48. 10.1016/S0921-5093(98)00649-2Suche in Google Scholar

[14] Y.Shahin, M.Acilar: Composites Part A34 (2003) 709. 10.1016/S1359-835X(03)00142-8Suche in Google Scholar

[15] M.K.Aghajanian, N.H.Macmillan, C.R.Kennedy, S.J.Luszcz, R.Roy: J. Mater. Sci.24 (1989) 58. 10.1007/BF01107457Suche in Google Scholar

[16] M.K.Aghajanian, M.A.Rocazella, J.T.Burke, S.D.Keck: J. Mater. Sci.26 (1991) 447. 10.1007/BF00576541Suche in Google Scholar

[17] K.B.Lee, H.Kwon: Metall. Mater. Trans. A30 (1999) 2999. 10.1007/s11661-999-0137-2Suche in Google Scholar

[18] A.M.Zahedi, H.R.Rezaie, J.Javadpour, M.Mazaheri, M.G.Haghighi: Ceram. Int.35 (2009) 1919. 10.1016/j.ceramint.2008.10.024Suche in Google Scholar

[19] X.Shen, S.Ren, X.He, M.Qin, X.Qu: J. Alloys Compd.468 (2009) 158. 10.1016/j.jallcom.2008.01.022Suche in Google Scholar

[20] J.A.Aguilar-Martinez, M.B.Hernandez, J.Castillo-Torres, M.I.Pech-Canul: Rev. Mex. Fis.53 (2007) 205.Suche in Google Scholar

[21] A.Aguilar-Martinez, M.I.Pech-Canul, M.Rodriguez-Reyes, J.L.De la Pena: J. Mater. Sci.39 (2004) 1025. 10.1023/B:JMSC.0000012936.48243.3aSuche in Google Scholar

[22] K.B.Lee, J.P.Ahn, H.Kwon: Metall. Mater. Trans. A (2001) 1007. 10.1007/s11661-001-0358-5Suche in Google Scholar

[23] K.B.Lee, H.Kwon: Metall. Mater. Trans. A33 (2002) 455. 10.1007/s11661-002-0106-5Suche in Google Scholar

[24] V.Kevrkijan: Metall. Mater. Trans. A35 (2004) 707. 10.1007/s11661-004-0381-4Suche in Google Scholar

[25] I.Kerti, F.Toptan: Mater. Lett.62 (2007) 1215. 10.1016/j.matlet.2007.08.015Suche in Google Scholar

[26] V.K.Singh, S.Chauhan, P.C.Gope, A.K.Chaudhary: High Temp. Mater. Processes34 (2014) 163. 10.1515/htmp-2014-0043Suche in Google Scholar

[27] J.Hashim, L.Looney, M.S.J.Hashmi: J. Mater. Process. Technol.119 (2001) 329. 10.1016/S0924-0136(01)00919-0Suche in Google Scholar

[28] S.Y.Oh, J.A.Cornie, K.C.Russell: Metall. Trans. A20 (1989) 527. 10.1007/BF02653932Suche in Google Scholar

[29] S.F.Corbin, X.Zhao-jie, H.Henein, P.S.Apte: Mater. Sci. Eng. A262 (1999) 192. 10.1016/S0921-5093(98)01019-3Suche in Google Scholar

[30] H.Sharifi, M.Divandari, A.R.Khavandi, M.H.Idris: Acta Metall. Sinica23 (2010) 241. 10.11890/1006-7191-104-241Suche in Google Scholar

[31] H.Sharifi, A.R.Khavandi, M.Divandari, M.I.Hasbullah: Int. J. Miner. Metall. Mater.19 (2012) 77. 10.1007/s12613-012-0518-1Suche in Google Scholar

[32] D.Lee, S.W.Park, D.B.Lee: Met. Mater. Int.14 (2008) 419. 10.3365/met.mat.2008.08.419Suche in Google Scholar

[33] S.R.Wang, Y.Z.Wang, Q.Chi: J. Mater. Sci.42 (2007) 7812. 10.1007/s10853-007-1591-0Suche in Google Scholar

[34] C.A.Leon-Patino, A.L. RobinDrew: Curr. Opin. Solid State Mater. Sci.9 (2005) 211. 10.1016/j.cossms.2006.04.006Suche in Google Scholar

Received: 2016-05-07
Accepted: 2016-06-27
Published Online: 2016-09-29
Published in Print: 2016-10-14

© 2016, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. A metastable phase diagram for the dynamic transformation of austenite at temperatures above the Ae3
  5. Experimental investigation of phase equilibria in the Co–Ni–Zr ternary system
  6. Phase equilibria of the Ni–Sb–Zn system at 600 °C
  7. High frequency cycling behaviour of three AZ magnesium alloys – microstructural characterisation
  8. Influence of auxetic foam in quasi-static axial crushing
  9. Electrochemical behaviour of iron and AISI 304 stainless steel in simulated acid rain solution
  10. Mechanochemical synthesis of CaMoO4 nanoparticles: kinetics and characterization
  11. Synthesis and characterization of iron oxide nanoparticles prepared hydrothermally at different reaction temperatures and pH
  12. Influence of SPS parameters on the density and hardness of zinc selenide
  13. Investigation into the kinetic behavior of molten aluminum pressureless infiltration into SiC preforms
  14. Review
  15. Centrifugal casting technique baseline knowledge, applications, and processing parameters: overview
  16. People
  17. Prof. Dr.-Ing. Jürgen Hirsch on the occasion of his 65th birthday
  18. DGM News
  19. DGM News
https://doi.org/10.3139/146.111422
Schlagwörter für diesen Artikel
Aluminum composite; SiC; Pressureless infiltration; Preform

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. A metastable phase diagram for the dynamic transformation of austenite at temperatures above the Ae3
  5. Experimental investigation of phase equilibria in the Co–Ni–Zr ternary system
  6. Phase equilibria of the Ni–Sb–Zn system at 600 °C
  7. High frequency cycling behaviour of three AZ magnesium alloys – microstructural characterisation
  8. Influence of auxetic foam in quasi-static axial crushing
  9. Electrochemical behaviour of iron and AISI 304 stainless steel in simulated acid rain solution
  10. Mechanochemical synthesis of CaMoO4 nanoparticles: kinetics and characterization
  11. Synthesis and characterization of iron oxide nanoparticles prepared hydrothermally at different reaction temperatures and pH
  12. Influence of SPS parameters on the density and hardness of zinc selenide
  13. Investigation into the kinetic behavior of molten aluminum pressureless infiltration into SiC preforms
  14. Review
  15. Centrifugal casting technique baseline knowledge, applications, and processing parameters: overview
  16. People
  17. Prof. Dr.-Ing. Jürgen Hirsch on the occasion of his 65th birthday
  18. DGM News
  19. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 21.9.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.111422/html
Button zum nach oben scrollen