Startseite Evaluation of Densification Mechanisms of Liquid-Phase Sintering
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Evaluation of Densification Mechanisms of Liquid-Phase Sintering

  • Sung-Min Lee und Suk-Joong L. Kang EMAIL logo
Veröffentlicht/Copyright: 11. Februar 2022
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 92 Heft 7

Abstract

The contact flattening between grains has long been considered to be the densification mechanism during liquidphase sintering. Recently, however, we proposed pore filling as being the major mechanism. In this investigation, we critically examine the two densification mechanisms by calculating their contributions to the sintering. The calculation shows that the contact flattening can be operative at the early stage for systems with a dihedral angle of zero degrees. However, its contribution to grain shape change and compact shrinkage is insignificant compared with that of the grain growth. A consideration of microstructures in real systems further suggests that the contribution of contact flattening is much less than the calculated value and is negligible from the beginning of the liquid-phase sintering. In fact, pore filling, which is induced by grain growth, appears to be essentially the only densification mechanism. An exemplified calculation of densification kinetics by pore filling is also presented and its implication discussed.

Keywords: Liquid-phase sintering; Pore filling theory; Densification mechanism; Grain growth; Calculation
Prof. Suk-Joong L. Kang Department of Materials Science and Engineering Taejon, 305–701, Korea Fax: +82 42 869 8920

Dedicated to Professor Dr. Dr. h. c. mult. Günter Petzow on the occasion of his 75th birthday

  1. This work was done under a joint research program of the Korea Advanced Institute of Science and Technology (KAIST) and the Institut National Polytechnique de Grenoble (INPG), supported by the Korean Ministry of Science and Technology (contract No. 99-I-03-057). The authors thank Mr. Sug-Woo Jung for his assistance in the preparation of the manuscript.

References

1 Kingery, W.D.: J. Appl. Phys. 30 (1959) 301.10.1063/1.1735155Suche in Google Scholar

2 Lee, S.-M. ; Kang, S.-J.L.: Acta. Mater. 46 (1998) 3191.10.1016/S1359-6454(97)00489-8Suche in Google Scholar

3 Cannon, H.S.; Lenel, F.V. in: F. Benesovsky (ed.), Proc. Plansee Seminar 1952, Metallwerk Plansee, Reutte (1953) 106.Suche in Google Scholar

4 Huppmann, W.J.; Riegger, H.: Acta Metall. 23 (1975) 965.10.1016/0001-6160(75)90010-3Suche in Google Scholar

5 Fortes, M.A.: Powd. Metall. Int. 14 (1982) 96.10.1051/gse:19820111Suche in Google Scholar

6 Belhadjhamida, A.; German, R.M., in: A. Lawley, A. Swanson (eds.), Advance in Powder Metallurgy and Particulate Materials, Vol. 3, Gorden and Breach, New York (1993) 85.Suche in Google Scholar

7 Lee, S.-M.; Chaix, J.M.; Martin, C.L.; Allibert, C.H.; Kang, S.-J.L.: Met. Mater. 5 (1999) 197.10.1007/BF03026053Suche in Google Scholar

8 Gessinger, G.H.; Fischmeister, H.F.; Lukas, H.L.: Acta Metall. 21 (1973) 715.10.1016/0001-6160(73)90082-5Suche in Google Scholar

9 Lifshitz, I.M.; Slyozov, V.V.: J. Phys. Chem. Solids 19 (1961) 35.10.1016/0022-3697(61)90054-3Suche in Google Scholar

10 Wagner, C.: Z. Elektrochem. 65 (1961) 581.10.1001/archopht.1961.01840020583023Suche in Google Scholar

11 Ardell, A.J.: Acta Metall. 20 (1972) 61.10.1016/0001-6160(72)90114-9Suche in Google Scholar

12 Brailsford, A.D.; Wynblatt, P.: Acta Metall. 27 (1979) 489.10.1016/0001-6160(79)90041-5Suche in Google Scholar

13 DeHoff, R.T.: Acta Metall. Mater. 39 (1991) 2349.10.1016/0956-7151(91)90016-TSuche in Google Scholar

14 German, R.M.; Olevsky, E.A.: Metall. Mater. Trans. A 29 (1998) 3057.10.1007/s11661-998-0213-zSuche in Google Scholar

15 Kingery, W.D.; Narasimhan, M.D.: J. Appl. Phys. 30 (1959) 307.10.1063/1.1735156Suche in Google Scholar

16 Kwon, O.-J.; Yoon, D.N.: Int. J. Powder Metall. Powder Tech. 17 (1981) 127.Suche in Google Scholar

17 Kang, S.-J.L.; Kaysser, W.A.; Petzow, G.; Yoon, D.N.: Powder Metall. 27 (1984) 97.10.1179/pom.1984.27.2.97Suche in Google Scholar

18 Kaysser, W.A.; Petzow, G.: Z. Metallkd. 76 (1985) 687.Suche in Google Scholar

19 Park, J.K.; Kang, S.-J.L.; Eun, K. Y.; Yoon, D. N.: Metall. Trans. A 20 (1989) 837.10.1007/BF02651650Suche in Google Scholar

20 Sarian, S.; Weart, H.W.: J. Appl. Phys. 37 (1966) 1675.10.1063/1.1708583Suche in Google Scholar

21 Kang, S.S.; Yoon, D.N.: Metall. Trans. A 13 (1982) 1405.10.1007/BF02642878Suche in Google Scholar

22 Kim, S.S.; Yoon, D.N.: Acta Metall. 31 (1983) 1151.10.1016/0001-6160(83)90177-3Suche in Google Scholar

23 Lee, D.-D.; Kang, S.-J.L.; Yoon, D.N.: J. Am. Ceram. Soc. 71 (1988) 803.10.1111/j.1151-2916.1988.tb06417.xSuche in Google Scholar

24 Kang, S.-J.L.; Han, S.-M.: MRS Bull. 20 (1995) 33.10.1557/S0883769400045085Suche in Google Scholar

25 Moon, H.; Kim, B.K.; Kang, S.-J.L.: Acta. Mater. 49 (2001) 1293.10.1016/S1359-6454(00)00394-3Suche in Google Scholar

26 Park, H.-H.; Cho, S.-J.; Yoon, D.N.: Metall. Trans. A 15 (1984) 1075.10.1007/BF02644700Suche in Google Scholar

27 Kang, S.-J.L.; Kim, K.-H.; Yoon, D.N.: J. Am. Ceram. Soc. 74 (1991) 425.10.1111/j.1151-2916.1991.tb06900.xSuche in Google Scholar

28 Kang, S.-J.L.; Kaysser, W.A.; Petzow, G.; Yoon, D.N.: Acta Metall. 33 (1985) 1919.10.1016/0001-6160(85)90014-8Suche in Google Scholar

29 Kaysser, W.A.; Zivkovic, M.; Petzow, G.: J. Mater. Sci. 20 (1985) 578.10.1007/BF01026528Suche in Google Scholar

30 Lee, D.-D.; Kang, S.-J.L.; Yoon, D.N.: Scripta Metall. 24 (1990) 927.10.1016/0956-716X(90)90139-8Suche in Google Scholar

31 Svoboda, J.; Riedel, H.; Gaebel, R.: Acta Mater. 44 (1996) 3215.10.1016/1359-6454(95)00440-8Suche in Google Scholar

32 Mortensen, A.: Acta Mater. 45 (1997) 749.10.1016/S1359-6454(96)00202-9Suche in Google Scholar

33 Kingery, W.D.; Berg, M.: J. Appl. Phys. 26 (1955) 1205.10.1063/1.1721874Suche in Google Scholar

34 Exner, H.E.; Bross, P.: Acta Metall. 27 (1979) 1007.10.1016/0001-6160(79)90188-3Suche in Google Scholar

35 Kang, S.-J.L.; Azou, P.: Powder Metall. 28 (1985) 90.10.1179/pom.1985.28.2.90Suche in Google Scholar

36 Park, H.-H.; Kang, S.-J.L.; Yoon, D.N.: Metall. Trans. A 17 (1986) 325.10.1007/BF02643908Suche in Google Scholar

37 Park, H.-H.; Kwon, O.-J.; Yoon, D.N.: Metall. Trans. A 17 (1986) 1915.10.1007/BF02644989Suche in Google Scholar

38 Kang, S.-J.L.; Lee, S.-M., in: R.M. German, G.L. Messing (eds.), Proc. Sintering ’99 – 2nd Int. Conf. on Science, Technology and Applications of Sintering, in press.Suche in Google Scholar

39 Park, H.H.; Yoon, D.N.: Metall. Trans. A 16 (1985) 923.10.1007/BF02814844Suche in Google Scholar

40 Yoon, D.N.; Huppmann W.J.: Acta Metall. 27 (1979) 693.10.1016/0001-6160(79)90020-8Suche in Google Scholar

41 Heady, R.B.; Cahn, J.W.: Metall. Trans. 1 (1970) 185.10.1007/BF02819260Suche in Google Scholar

42 Eremenko, V.N.; Naidich, Y.V.; Lavrinenko, I.A.: Liquid-Phase Sintering, Consultants Bureau, New York (1970).10.1007/978-1-4757-5665-4Suche in Google Scholar

43 Tewari, A.; Gokhale, A.M.; German, R.M.: Acta Mater. 47 (1999) 3721.10.1016/S1359-6454(99)00164-0Suche in Google Scholar

44 Louis, P.; Gokhale, A.M.: Acta, Metall. Mater. 44 (1996) 1519.10.1016/1359-6454(95)00296-0Suche in Google Scholar

45 Churn, K.S.; German, R.M.: Metall. Trans. A 15 (1984) 331.10.1007/BF02645119Suche in Google Scholar

46 Carter, W.C., in: L.-Q. Chen et al. (eds.), Mathematics of Microstructure Evolution, The Minerals, Metals & Materials Society, Philadelphia, PA (1996) 1.Suche in Google Scholar

47 Hough, R.R.; Rolls R.: Metall. Trans. 2 (1971) 2471.10.1007/BF02814884Suche in Google Scholar

48 Ejima, T.; Kameda, M.: J. Jpn. Inst. Met. 33 (1969) 96.10.2320/jinstmet1952.33.1_96Suche in Google Scholar

49 Kleebe, H.-J.; Cinibulk, M.K.; Cannon, R.M.; Rühle, M.: J. Am. Ceram. Soc. 76 (1993) 1969.10.1111/j.1151-2916.1993.tb08319.xSuche in Google Scholar

50 Luo, J.; Wang H.; Chiang, Y.-M.: J. Am. Ceram. Soc. 82 (1999) 916.10.1111/j.1151-2916.1999.tb01853.xSuche in Google Scholar

51 Chung, S.-Y.: Ph. D. Thesis, Korea Advanced Institute of Science and Technology, Taejon (2001).Suche in Google Scholar

52 Hansen, M.; Anderko, K.: Constitution of Binary Alloys, McGraw-Hill, New York (1958).10.1149/1.2428700Suche in Google Scholar

53 Gans, W.; Pawlek, F., Rüpenack A.V.: Z. Metallkd. 54 (1963) 147.10.1515/ijmr-1963-540305Suche in Google Scholar

54 B.D. Cullity: Elements of X-Ray Diffraction, Addison-Wesley, Reading, MA (1978).Suche in Google Scholar

55 Hwang, N.-M.; Kang, S.-J.L.; Yoon, D.N.: Metall. Trans. A 17 (1986) 1429.10.1007/BF02650124Suche in Google Scholar

56 Kim, Y.-P.: M.S. Thesis, Korea Advanced Institute of Science and Technology, Taejon (2000).Suche in Google Scholar

57 Yoon, D.N.; Huppmann, W. J.: Acta Metall. 27 (1979) 973.10.1016/0001-6160(79)90185-8Suche in Google Scholar

58 King, A.H.: Int. Mater. Rev. 32 (1987) 173.10.1179/095066087790150304Suche in Google Scholar

59 Yoon, D.Y.: Int. Mater. Rev. 40 (1995) 149.10.1179/imr.1995.40.4.149Suche in Google Scholar

60 Jeon, J.H.; Kang, S.-J.L.: J. Am. Ceram. Soc. 77 (1994) 1688.10.1111/j.1151-2916.1994.tb09781.xSuche in Google Scholar

61 Lee, H.-Y.; Kim, J.-S.; Kang, S.-J.L.: Interface Sci. 8 (2000) 223.10.1023/A:1008768320484Suche in Google Scholar
Received: 2001-04-16
Published Online: 2022-02-11

© 2001 Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Frontmatter
  2. Editorial
  3. “No wise man ever wish to be younger”
  4. Aufsätze/Articles
  5. Entropy, Transformations and Sustainability of Industrial Life Cycles
  6. Positron Annihilation in Stable and Supercooled Metallic Melts
  7. Local Characterization of the Diffusion Process during Discontinuous Precipitation: A Review
  8. The Dependence of Abnormal Grain Growth on Initial Grain Size in 316 L Stainless Steel
  9. Diffusion-Controlled Grain Growth in Liquid-Phase Sintering of W–Cu Nanocomposites
  10. Evaluation of Densification Mechanisms of Liquid-Phase Sintering
  11. Phase Transformation of a Dual Phase Al–Fe Alloy Prepared by Mechanical Alloying
  12. Discrete Element Simulation of Ceramic Powder Processing
  13. Strain Relaxation and Internal Friction in the Range of the Glass Transition
  14. A Thermodynamic Model of an Amorphous Grain Boundary Phase in Liquid-Phase Sintered β-SiAlON Ceramic
  15. Epitaxial Growth of Metals on (100) SrTiO3: The Influence of Lattice Mismatch and Reactivity
  16. Microstructure and Modifications of Cu/Al2O3 Interfaces
  17. Structural Transformations Induced by Swift Heavy Ions in Polysiloxanes and Polycarbosilanes
  18. Metastable Al–Nd–Ni and Stable Al–La–Ni Phase Equilibria
  19. Phase Equilibria of the Al–Nd and Al–Nd–Ni Systems
  20. System Pr –Pd–O: Phase Diagram and Thermodynamic Properties of Ternary Oxides Using Solid-State Cells with Special Features
  21. Calculation of Phase Equilibria in Candidate Solder Alloys
  22. Thermodynamic Assessment of the Zr–O Binary System
  23. Delaminating Layered Oxide Composites with Wavy Interfaces
  24. Contemporary Materials Issues for Advanced EB-PVD Thermal Barrier Coating Systems
  25. Monte Carlo Simulations of Strength Distributions of Brittle Materials – Type of Distribution, Specimen and Sample Size
  26. On the Optimization of the Microstructure in Powder Metallurgical Ag–SnO2–In2O3 Contact Materials
  27. Some New Aspects of Microstructural Design of β-Si3N4 Ceramics
  28. Ni-Based SOFC Anodes: Microstructure and Electrochemistry
  29. Effect of Copper Line Geometry and Process Parameters on Interconnect Microstructure and Degradation Processes
  30. Thermal Stability of Nanoscale Co/Cu Multilayers
  31. Methods for Characterising the Precipitation of Nanometer-Sized Secondary Hardening Carbides and Related Effects in Tool Steels
  32. Prediction of Local Strain and Hardness in Sheet Forming
  33. Novel in situ-Infiltrated Al2O3-Metal Composites
  34. Influence of Microstructure and Impurities on Thermal Conductivity of Aluminium Nitride Ceramics
  35. Notifications/Mitteilungen
  36. Personelles/Personal
  37. Bücher/Books
  38. Tagungen/Conferences
https://doi.org/10.1515/ijmr-2001-0128
Schlagwörter für diesen Artikel
Liquid-phase sintering; Pore filling theory; Densification mechanism; Grain growth; Calculation

Artikel in diesem Heft

  1. Frontmatter
  2. Editorial
  3. “No wise man ever wish to be younger”
  4. Aufsätze/Articles
  5. Entropy, Transformations and Sustainability of Industrial Life Cycles
  6. Positron Annihilation in Stable and Supercooled Metallic Melts
  7. Local Characterization of the Diffusion Process during Discontinuous Precipitation: A Review
  8. The Dependence of Abnormal Grain Growth on Initial Grain Size in 316 L Stainless Steel
  9. Diffusion-Controlled Grain Growth in Liquid-Phase Sintering of W–Cu Nanocomposites
  10. Evaluation of Densification Mechanisms of Liquid-Phase Sintering
  11. Phase Transformation of a Dual Phase Al–Fe Alloy Prepared by Mechanical Alloying
  12. Discrete Element Simulation of Ceramic Powder Processing
  13. Strain Relaxation and Internal Friction in the Range of the Glass Transition
  14. A Thermodynamic Model of an Amorphous Grain Boundary Phase in Liquid-Phase Sintered β-SiAlON Ceramic
  15. Epitaxial Growth of Metals on (100) SrTiO3: The Influence of Lattice Mismatch and Reactivity
  16. Microstructure and Modifications of Cu/Al2O3 Interfaces
  17. Structural Transformations Induced by Swift Heavy Ions in Polysiloxanes and Polycarbosilanes
  18. Metastable Al–Nd–Ni and Stable Al–La–Ni Phase Equilibria
  19. Phase Equilibria of the Al–Nd and Al–Nd–Ni Systems
  20. System Pr –Pd–O: Phase Diagram and Thermodynamic Properties of Ternary Oxides Using Solid-State Cells with Special Features
  21. Calculation of Phase Equilibria in Candidate Solder Alloys
  22. Thermodynamic Assessment of the Zr–O Binary System
  23. Delaminating Layered Oxide Composites with Wavy Interfaces
  24. Contemporary Materials Issues for Advanced EB-PVD Thermal Barrier Coating Systems
  25. Monte Carlo Simulations of Strength Distributions of Brittle Materials – Type of Distribution, Specimen and Sample Size
  26. On the Optimization of the Microstructure in Powder Metallurgical Ag–SnO2–In2O3 Contact Materials
  27. Some New Aspects of Microstructural Design of β-Si3N4 Ceramics
  28. Ni-Based SOFC Anodes: Microstructure and Electrochemistry
  29. Effect of Copper Line Geometry and Process Parameters on Interconnect Microstructure and Degradation Processes
  30. Thermal Stability of Nanoscale Co/Cu Multilayers
  31. Methods for Characterising the Precipitation of Nanometer-Sized Secondary Hardening Carbides and Related Effects in Tool Steels
  32. Prediction of Local Strain and Hardness in Sheet Forming
  33. Novel in situ-Infiltrated Al2O3-Metal Composites
  34. Influence of Microstructure and Impurities on Thermal Conductivity of Aluminium Nitride Ceramics
  35. Notifications/Mitteilungen
  36. Personelles/Personal
  37. Bücher/Books
  38. Tagungen/Conferences
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 1.10.2025 von https://www.degruyterbrill.com/document/doi/10.1515/ijmr-2001-0128/html?lang=de
Button zum nach oben scrollen