Startseite Processing by severe plastic deformation:an ancient skill adapted for the modern world
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Processing by severe plastic deformation:an ancient skill adapted for the modern world

  • Ruslan Z. Valiev , Kenong Xia und Terence G. Langdon
Veröffentlicht/Copyright: 11. Juni 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 100 Heft 12

Abstract

The processing of bulk solids through the application of severe plastic deformation has now become a well-established procedure for achieving grain refinement to the submicrometer or even the nanometer level. Several basic techniques are currently in place but most attention has been devoted to the procedures of equal-channel angular pressing, high-pressure torsion and accumulative roll-bonding. This paper presents an introductory overview of processing by severe plastic deformation including historical developments and recent new advances in the processing technology. Special emphasis is placed on the move towards the commercialization of the severe plastic deformation approach.

Keywords: Accumulative roll-bonding; Equal-channel angular pressing; High-pressure torsion; Severe plastic deformation; Ultrafine grains
* Correspondence address Professor Kenong Xia, Department of Mechanical Engineering, University of Melbourne Victoria 3010, Australia Tel.: +61 3 8344 6664 Fax: +61 3 9347 8784 E-mail:

References

[1] R.Z.Valiev, Y.Estrin, Z.Horita, T.G.Langdon, M.J.Zehetbauer, Y.T.Zhu: JOM58 (4) (2006) 33.10.1007/s11837-006-0213-7Suche in Google Scholar

[2] R.Z.Valiev, R.K.Islamgaliev, I.V.Alexandrov: Prog. Mater. Sci.45 (2000) 103.10.1016/S0079-6425(99)00007-9Suche in Google Scholar

[3] J.T.Wang: Mater. Sci. Forum503–504 (2006) 363.10.4028/www.scientific.net/MSF.503-504.363Suche in Google Scholar

[4] P.W.Bridgman: J. Appl. Phys.14 (1943) 273.10.1063/1.1714987Suche in Google Scholar

[5] N.A.Smirnova, V.I.Levit, V.I.Pilyugin, R.I.Kuznetsov, L.S.Davydova, V.A.Sazonova: Fiz. Metal. Metalloved.61 (1986) 1170.Suche in Google Scholar

[6] V.M.Segal, V.I.Reznikov, A.E.Drobyshevskiy, V.I.Kopylov: Russian Metall.1 (1981) 99.Suche in Google Scholar

[7] R.Z.Valiev, O.A.Kaibyshev, R.I.Kuznetsov, R.Sh.Musalimov, N.K.Tsenev: Dokl. Akad. Nauk SSSR301 (1988) 864.Suche in Google Scholar

[8] R.Z.Valiev, N.A.Krasilnikov, N.K.Tsenev: Mater Sci Eng. A137 (1991) 35.10.1016/0921-5093(91)90316-FSuche in Google Scholar

[9] R.Z.Valiev, T.G.Langdon: Prog. Mater. Sci.51 (2006) 881.10.1016/j.pmatsci.2006.02.003Suche in Google Scholar

[10] Z.Horita, T.Fujinami, T.G.Langdon: Mater. Sci. Eng. A318 (2001) 34.10.1016/S0921-5093(01)01339-9Suche in Google Scholar

[11] A.P.Zhilyaev, T.G.Langdon: Prog. Mater. Sci.53 (2008) 893.10.1016/j.pmatsci.2008.03.002Suche in Google Scholar

[12] G.Sakai, K.Nakamura, Z.Horita, T.G.Langdon: Mater. Sci. Eng. A406 (2005) 268.10.1016/j.msea.2005.06.049Suche in Google Scholar

[13] Y.Saito, N.Tsuji, M.Utsunomiya, T.Sakai, R.G.Hong: Scripta Mater.39 (1998) 1221.10.1016/S1359-6462(98)00302-9Suche in Google Scholar

[14] J.Huang, Y.T.Zhu, H.Jiang, T.C.Lowe: Acta Mater.49 (2001) 1497.10.1016/S1359-6454(01)00069-6Suche in Google Scholar

[15] Y.T.Zhu, H.Jiang, J.Huang, T.C.Lowe: Metall. Mater. Trans. A32 (2001) 1559.10.1007/s11661-001-0245-0Suche in Google Scholar

[16] Y.Saito, H.Utsunomiya, H.Suzuki, T.Sakai: Scripta Mater.42 (2000) 1139.10.1016/S1359-6462(00)00349-3Suche in Google Scholar

[17] J.C.Lee, H.K.Seok, J.Y.Suh: Acta Mater.50 (2002) 4005.10.1016/S1359-6454(02)00200-8Suche in Google Scholar

[18] G.J.Raab, R.Z.Valiev, T.C.Lowe, Y.T.Zhu: Mat. Sci. Eng. A382 (2004) 30.10.1016/j.msea.2004.04.021Suche in Google Scholar

[19] R.Z.Valiev, A.V.Korznikov, R.R.Mulyukov: Mater. Sci Eng. A186 (1993) 141.10.1016/0921-5093(93)90717-SSuche in Google Scholar

[20] R.Z.Valiev, R.S.Mishra, J.Grosa, A.K.Mukherjee: Scripta Mater.34 (1996) 1443.10.1016/1359-6462(95)00676-1Suche in Google Scholar

[21] A.R.Yavari, W.J.Botta, C.A.D.Rodriguez, C.Cardoso, R.Z.Valiev: Scripta Mater.46 (2002) 711.10.1016/S1359-6462(02)00057-XSuche in Google Scholar

[22] R.Z.Valiev: Adv. Eng. Mater.5 (2003) 296.10.1002/adem.200310089Suche in Google Scholar

[23] N.Boucharat, R.Hebert, H.Rösner, R.Valiev, G.Wilde: Scripta Mater.53 (2005) 823.10.1016/j.scriptamat.2005.06.004Suche in Google Scholar

[24] R.Z.Valiev, V.G.Pushin, D.V.Gunderov, A.G.Popov: Doklady RAN398 (2004) 1.Suche in Google Scholar

[25] A.V.Sergueeva, C.Song, R.Z.Valiev, A.K.Mukherjee: Mater. Sci. Eng. A339 (2003) 159.10.1016/S0921-5093(02)00122-3Suche in Google Scholar

[26] D.G.Morris: Mechanical Behaviour of Nanostructured Materials, Trans. Tech., Uetikon-Zurich, Switzerland (1998).Suche in Google Scholar

[27] C.C.Koch: Scripta Mater.49 (2003) 657.10.1016/S1359-6462(03)00394-4Suche in Google Scholar

[28] R.Z.Valiev: Nature Mater.3 (2004) 511. PMid:15286754;10.1038/nmat1180Suche in Google Scholar

[29] R.Z.Valiev, I.V.Alexandrov, T.C.Lowe, Y.T.Zhu: J. Mater. Res.17 (2002) 5.10.1557/JMR.2002.0002Suche in Google Scholar

[30] Z.Horita, K.Ohashi, T.Fujita, K.Kaneko, T.G.Langdon: Adv. Mater.17 (2005) 1599.10.1002/adma.200500069Suche in Google Scholar

[31] Y.Wang, M.Chen, F.Zhou, E.Ma: Nature419 (2002) 912. PMid:12410306;10.1038/nature01133Suche in Google Scholar

[32] R.Z.Valiev, A.V.Sergueeva, A.K.Mukherjee: Scripta Mater.49 (2003) 669.10.1016/S1359-6462(03)00395-6Suche in Google Scholar

[33] E.Ma: Scripta Mater.49 (2003) 663.10.1016/S1359-6462(03)00396-8Suche in Google Scholar

[34] Y.M.Wang, E.Ma: Acta Mater.52 (2004) 1699.10.1016/j.actamat.2003.12.022Suche in Google Scholar

[35] E.Ma: JOM58 (4) (2006) 49.10.1007/s11837-006-0215-5Suche in Google Scholar

[36] X.Zhang, H.Wang, R.O.Scattergood, J.Narayan, C.C.Koch, A.V.Sergueeva, A.K.Mukherjee: Acta Mater.50 (2002) 4823.10.1016/S1359-6454(02)00349-XSuche in Google Scholar

[37] H.Mughrabi, H.W.Höppel: Z. Metallkd.94 (2003) 1079.Suche in Google Scholar

[38] Y.S.Park, K.H.Chung, N.J.Kim, E.J.Lavernia: Mater. Sci. Eng. A374 (2004) 211.10.1016/j.msea.2004.02.013Suche in Google Scholar

[39] L.Lu, Y.Shen, X.Chen, L.Qian, K.Lu: Science304 (2004) 422. PMid:15031435;10.1126/science.1092905Suche in Google Scholar

[40] E.Ma, Y.M.Wang, Q.H.Lu, M.L.Sui, L.Lu, K.Lu: Appl. Phys. Lett.85 (2004) 4932.10.1063/1.1814431Suche in Google Scholar

[41] R.Z.Valiev, E.V.Kozlov, Yu.F.Ivanov, J.Lian, A.A.Nazarov, B.Baudelet: Acta Metall. Mater.42 (1994) 2467.10.1016/0956-7151(94)90326-3Suche in Google Scholar

[42] T.G.Nieh, J.Wadsworth, O.D.Sherby: Superplasticity in Metals and Ceramics, Cambridge Univ. Press, Cambridge (1997).10.1017/CBO9780511525230Suche in Google Scholar

[43] H.Van Swygenhoven: Science296 (2002) 66. PMid:11935012;10.1126/science.1071040Suche in Google Scholar

[44] V.Yamakov, D.Wolf, S.R.Phillpot, A.K.Mukherjee, H.Gleiter: Nature Mater.1 (2002) 1. PMid:12618848;10.1038/nmat700Suche in Google Scholar

[45] J.Schiøtz, K.W.Jacobsen: Science301 (2003) 1357. PMid:12958354;10.1126/science.1086636Suche in Google Scholar

[46] M.G.Zelin, N.A.Krasilnikov, R.Z.Valiev, M.W.Grabski, H.S.Yang, A.K.Mukherjee: Acta Metall. Mater.42 (1994) 19.10.1016/0956-7151(94)90054-XSuche in Google Scholar

[47] H.Hahn, K.A.Padmanabhan: Phil. Mag. B76 (1997) 559.10.1080/01418639708241122Suche in Google Scholar

[48] M.Chen, E.Ma, K.J.Hemker, H.Sheng, Y.Wang, X.Cheng: Science300 (2003) 1275. PMid:12714676;10.1126/science.1083727Suche in Google Scholar

[49] X.Z.Liao, F.Zhou, E.J.Lavernia, D.W.He, Y.T.Zhu: Appl. Phys. Lett.83 (2003) 5062.10.1063/1.1633975Suche in Google Scholar

[50] H.W.HöppelZ.M.Zhou, H.Mughrabi, R.Z.Valiev: Phil Mag. A82 (2002) 1781.10.1080/01418610208235689Suche in Google Scholar

[51] A.Vinogradov, S.Hashimoto: Adv. Eng. Mater.5 (2003) 351.10.1002/adem.200310078Suche in Google Scholar

[52] K.Xia: Mater. Sci. Forum579 (2008) 61.10.4028/www.scientific.net/MSF.579.61Suche in Google Scholar

[53] K.Xia, W.Xu, X.Wu, S.Goussous: Mater. Sci. Forum584–586 (2008) 119.10.4028/www.scientific.net/MSF.584-586.119Suche in Google Scholar

[54] R.W.Hayes, R.Rodriguez, E.J.Lavernia: Acta Mater.49 (2001) 4055.10.1016/S1359-6454(01)00278-6Suche in Google Scholar

[55] W.Xu, T.Honma, X.Wu, S.P.Ringer, K.Xia: Appl. Phys. Lett.91 (2007) 031901.10.1063/1.2755923Suche in Google Scholar

[56] W.Xu, X.Wu, D.Sadedin, G.Wellwood, K.Xia: Appl. Phys. Lett.92 (2008) 011924.10.1063/1.2832657Suche in Google Scholar

[57] K.Xia, X.Wu: Scripta Mater.53 (2005) 1225.10.1016/j.scriptamat.2005.08.012Suche in Google Scholar

[58] M.Haouaoui, I.Karaman, H.J.Maier, K.T.Hartwig: Metall. Mater. Trans. A35 (2004) 2935.10.1007/s11661-004-0241-2Suche in Google Scholar

[59] M.Moss, R.Lapovok, C.J.Bettles: JOM59(8) (2007) 84.10.1007/s11837-007-0105-5Suche in Google Scholar

[60] R.Lapovok, D.Tomus, C.Bettles: Scripta Mater.58 (2008) 898.10.1016/j.scriptamat.2008.01.010Suche in Google Scholar

[61] A.V.Korznikov, I.M.Safarov, D.V.Laptionok, R.Z.Valiev: Acta Metall. Mater.39 (1991) 3193.10.1016/0956-7151(91)90054-5Suche in Google Scholar

[62] K.Xia, X.Wu, T.Honma, S.P.Ringer: J. Mater. Sci.42 (2007) 1551.10.1007/s10853-006-0819-8Suche in Google Scholar

[63] S.C.Tjong: Adv. Eng. Mater.9 (2007) 639.10.1002/adem.200700106Suche in Google Scholar

[64] S.Goussous, W.Xu, X.Wu, K.Xia: Comp. Sci. Technol.69 (2009) 1997.10.1016/j.compscitech.2009.05.004Suche in Google Scholar

[65] I.Sabirov, R.Pippan: Scripta Mater.52 (2005) 1293.10.1016/j.scriptamat.2005.02.017Suche in Google Scholar

[66] D.B.Witkin, E.J.Lavernia: Prog. Mater. Sci.51 (2006) 1.10.1016/j.pmatsci.2005.04.004Suche in Google Scholar

[67] Z.Lee, F.Zhou, R.Z.Valiev, E.J.Lavernia, S.R.Nutt: Scripta Mater.51 (2004) 209.10.1016/j.scriptamat.2004.04.016Suche in Google Scholar

[68] B.Q.Han, Z.Lee, S.R.Nutt, E.J.Lavernia, F.A.Mohamed: Metall. Mater. Trans. A34 (2003) 603.10.1007/s11661-003-0095-zSuche in Google Scholar

[69] T.C.Lowe: JOM58(4) (2006) 28.10.1007/s11837-006-0212-8Suche in Google Scholar

[70] R.Z.Valiev, M.J.Zehetbauer, Y.Estrin, H.W.Höppel, Y.Ivanisenko, H.Hahn, G.Wilde, H.J.Roven, X.Sauvage, T.G.Langdon: Adv. Eng. Mater.9 (2007) 527.10.1002/adem.200700078Suche in Google Scholar

[71] D.M.Brunette, P.Tengvall, M.Textor, P.Thomsen (Eds.): Titanium in Medicine, Springer, Heidelberg, 2001.10.1007/978-3-642-56486-4Suche in Google Scholar

[72] V.V.Stolyarov, Y.T.Zhu, I.V.Alexandrov, T.C.Lowe, R.Z.Valiev: Mater. Sci. Eng. A343 (2003) 43.10.1016/S0921-5093(02)00366-0Suche in Google Scholar

[73] R.Z.Valiev, I.P.Semenova, V.V.Latysh, H.Rack, T.C.Lowe, J.Petruzelka, L.Dluhos, D.Hrusak, J.Sochova: Adv. Eng. Mater. B15 (2008) 10.Suche in Google Scholar

[74] C.N.Elias, J.H.C.Lima, R.Valiev, M.A.Meyers: JOM60(3) (2008) 46.10.1007/s11837-008-0031-1Suche in Google Scholar

[75] Z.Horita, M.Furukawa, M.Nemoto, A.J.Barnes, T.G.Langdon: Acta Mater.48 (2000) 3633.10.1016/S1359-6454(00)00182-8Suche in Google Scholar

[76] H.Akamatsu, T.Fujinami, Z.Horita, M.Nemoto, T.G.Langdon: Scripta Mater.44 (2001) 759.10.1016/S1359-6462(00)00666-7Suche in Google Scholar

[77] K.T.Park, H.J.Lee, C.S.Lee, W.J.Nam, D.H.Shin: Scripta Mater.51 (2004) 479.Suche in Google Scholar

[78] I.Nikulin, R.Kaibyshev, T.Sakai: Mater. Sci. Eng. A407 (2005) 62.10.1016/j.msea.2005.06.014Suche in Google Scholar

[79] R.Z.Valiev, D.A.Salimonenko, N.K.Tsenev, P.B.Berbon, T.G.Langdon: Scripta Mater.37 (1997) 1945.Suche in Google Scholar

[80] A.V.Korznikov, I.M.Safarov, A.A.Nazarov, R.Z.Valiev: Mat. Sci. Eng A206 (1996) 39.10.1016/0921-5093(95)09981-6Suche in Google Scholar

[81] M.Z.Borisova, S.P.Yakovleva, A.M.Ivanov: Solid State Phenom.14 (2006) 97.10.4028/www.scientific.net/SSP.114.97Suche in Google Scholar

[82] R.Lapovok, R.Cottam, G.Stecher, R.Deam, E.Summerville, in: T.C.Lowe, R.Z.Valiev (Eds.), Investigations and Applications of Severe Plastic Deformation, Kluwer, Dordrecht, The Netherlands (2000) 303.10.1007/978-94-011-4062-1_39Suche in Google Scholar

Received: 2009-3-29
Accepted: 2009-9-15
Published Online: 2013-06-11
Published in Print: 2009-12-01

© 2009, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Review of IJMR's centenary year
  5. Proceedings of the SPD Workshop, Melbourne, June 2009
  6. Feature
  7. Processing by severe plastic deformation:an ancient skill adapted for the modern world
  8. Review
  9. Grain refinement and growth induced by severe plastic deformation
  10. Basic
  11. The nature of grain refinement in equal-channel angular pressing: a comparison of representative fcc and hcp metals
  12. Ductility of ultrafine-grained copper processed by equal-channel angular pressing
  13. Technical parameters affecting grain refinement by high pressure torsion
  14. Nanocrystalline body-centred cubic beta-titanium alloy processed by high-pressure torsion
  15. Softening of high purity aluminum and copper processed by high pressure torsion
  16. An atom probe characterisation of grain boundaries in an aluminium alloy processed by equal-channel angular pressing
  17. Deformation mechanisms in an ultra-fine grained Al alloy
  18. Applied
  19. The effect of back pressure on mechanical properties of an Mg-3 wt.% Al-1 wt.% Zn alloy with single pass equal channel angular pressing
  20. Nanostructuring of Ti-alloys by SPD processing to achieve superior fatigue properties
  21. Improvement in the strength and ductility of Al-Mg-Mn alloys with Zr and Sc additions by equal channel angular pressing
  22. The effect of initial microstructure and processing temperature on microstructure and texture in multilayered Al/Al(Sc) ARB sheets
  23. Plastic deformation analysis of accumulative back extrusion
  24. The possibility of synthesizing bulk nanostructured or ultrafine structured metallic materials by consolidation of powders using high strain powder compact forging
  25. Use of residual hydrogen to produce CP-Ti powder compacts for low temperature rolling
  26. Mg alloy for hydrogen storage processed by SPD
  27. DGM News
  28. Personal/Conferences/Imprint
https://doi.org/10.3139/146.110233
Schlagwörter für diesen Artikel
Accumulative roll-bonding; Equal-channel angular pressing; High-pressure torsion; Severe plastic deformation; Ultrafine grains

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Review of IJMR's centenary year
  5. Proceedings of the SPD Workshop, Melbourne, June 2009
  6. Feature
  7. Processing by severe plastic deformation:an ancient skill adapted for the modern world
  8. Review
  9. Grain refinement and growth induced by severe plastic deformation
  10. Basic
  11. The nature of grain refinement in equal-channel angular pressing: a comparison of representative fcc and hcp metals
  12. Ductility of ultrafine-grained copper processed by equal-channel angular pressing
  13. Technical parameters affecting grain refinement by high pressure torsion
  14. Nanocrystalline body-centred cubic beta-titanium alloy processed by high-pressure torsion
  15. Softening of high purity aluminum and copper processed by high pressure torsion
  16. An atom probe characterisation of grain boundaries in an aluminium alloy processed by equal-channel angular pressing
  17. Deformation mechanisms in an ultra-fine grained Al alloy
  18. Applied
  19. The effect of back pressure on mechanical properties of an Mg-3 wt.% Al-1 wt.% Zn alloy with single pass equal channel angular pressing
  20. Nanostructuring of Ti-alloys by SPD processing to achieve superior fatigue properties
  21. Improvement in the strength and ductility of Al-Mg-Mn alloys with Zr and Sc additions by equal channel angular pressing
  22. The effect of initial microstructure and processing temperature on microstructure and texture in multilayered Al/Al(Sc) ARB sheets
  23. Plastic deformation analysis of accumulative back extrusion
  24. The possibility of synthesizing bulk nanostructured or ultrafine structured metallic materials by consolidation of powders using high strain powder compact forging
  25. Use of residual hydrogen to produce CP-Ti powder compacts for low temperature rolling
  26. Mg alloy for hydrogen storage processed by SPD
  27. DGM News
  28. Personal/Conferences/Imprint
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 16.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.110233/pdf?lang=de
Button zum nach oben scrollen