Heat transfer distribution of single oblique jet impingement in crossflow under different inlet conditions
-
Juan He
,
Kun Xiao
Abstract
To further reveal the interaction between crossflow and jet, single oblique jet impingement in crossflow is studied. The influences of Reynolds number (Re = 3750–15,000), oblique angle (θ = 50°–90°), jet intake mode (jet normal to inlet plane and jet along hole axis), crossflow ratio (CR = 0.1–0.3) and temperature ratio (TR = 1.0–1.2) are considered. For both jet intake modes, with the decrease of θ, the peak value of Nusselt number increases and its location shifts upstream. The Nusselt number for case of jet normal to inlet plane is higher than that of jet along hole axis with wider lateral coverage range. The CR affects the convection heat transfer between crossflow and target surface, and it also affects the interaction between crossflow and jet. Synthetically, the best heat transfer appears at CR = 0.2. The Nusselt number decreases sharply when TR goes from 1.0 to 1.1, while the decline trend slows down when TR goes from 1.1 to 1.2.
-
Author contribution: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Research funding: None declared.
-
Conflict of interest statement: The authors declare no conflicts of interest regarding this article.
References
1. Martin, H. Heat and mass transfer between impinging gas jets and solid surfaces. Adv Heat Tran 1977;13:1–60, https://doi.org/10.1016/s0065-2717(08)70221-1.Search in Google Scholar
2. Viskanta, R. Heat transfer to impinging isothermal gas and flame jets. Exp Therm Fluid Sci 1993;6:111–34, https://doi.org/10.1016/0894-1777(93)90022-b.Search in Google Scholar
3. Goldstein, RJ, Behbahani, AI, Heppelmann, KK. Streamwise distribution of the recovery factor and the local heat transfer coefficient to an impinging circular air jet. Int J Heat Mass Tran 1986;29:1227–35, https://doi.org/10.1016/0017-9310(86)90155-9.Search in Google Scholar
4. Downs, SJ, James, EH. Jet impingement heat transfer-a literature survey. In: 24th national heat transfer conference and exhibition, Pennsylvania; 1987.Search in Google Scholar
5. Lee, DH, Chung, YS, Won, SY. The effect of concave surface curvature on heat transfer from a fully developed round impinging jet. Int J Heat Mass Tran 1999;42:2489–97, https://doi.org/10.1016/s0017-9310(98)00318-4.Search in Google Scholar
6. Mao, JK, Liu, ZX, Guo, W. Experiment of heat transfer on concave surface in single jet impingement cooling system in small jet-to-target space. J Propuls Technol 2008;29:143–8.Search in Google Scholar
7. Pawar, S, Patel, DK. The impingement heat transfer data of inclined jet in cooling applications: a review. J Therm Sci 2019;29:1–12, https://doi.org/10.1007/s11630-019-1200-y.Search in Google Scholar
8. Hollworth, BR, Berry, RD. Heat transfer from arrays of impinging jets with large jet-to-jet spacing. J Heat Tran 1978;100:352–7, https://doi.org/10.1115/1.3450808.Search in Google Scholar
9. Huber, AM, Viskanta, R. Effect of jet-jet spacing on convective heat transfer to confined, impinging arrays of axisymmetric air jets. Int J Heat Mass Tran 1994;37:2859–69, https://doi.org/10.1016/0017-9310(94)90340-9.Search in Google Scholar
10. Xie, R, Wang, H, Xu, B, Wang, W. A review of impingement jet cooling in combustor liner. Oslo, Norway: ASME Turbo Expo; 2018, GT2018-76335.10.1115/GT2018-76335Search in Google Scholar
11. Xing, Y, Spring, S, Weigand, B. Experimental and numerical investigation of heat transfer characteristics of inline and staggered arrays of impinging jets. J Heat Tran 2010;132:53–8, https://doi.org/10.1115/1.4001633.Search in Google Scholar
12. Goodro, M, Park, J, Ligrani, P, Fox, M, Moon, HK. Effect of temperature ratio on jet array impingement heat transfer. J Heat Tran 2009;131:103–12, https://doi.org/10.1115/1.2977546.Search in Google Scholar
13. Ekkad, SV, Kontrovitz, D, Nasir, H. Effect of rib turbulators in the first pass on heat transfer distributions in a two-pass channel connected by two rows of holes. New Orleans, Louisiana, USA: ASME Turbo Expo; 2001, 2001-GT-0184.10.1115/2001-GT-0184Search in Google Scholar
14. Ekkad, SV, Pamula, G, Acharya, S. Influence of crossflow-induced swirl and impingement on heat transfer in an internal coolant passage of a turbine airfoil. J Heat Tran 2000;122:27–39, https://doi.org/10.1115/1.1289020.Search in Google Scholar
15. Esposito, E, Ekkad, SV. Jet impingement heat transfer visualization using a steady state liquid crystal method. J Heat Tran 2006;128:738, https://doi.org/10.1115/1.2221301.Search in Google Scholar
16. Taslim, ME, Pan, Y, Bakhtari, K. Experimental racetrack shaped jet impingement on a roughened leading-edge wall with film holes. Amsterdam, The Netherlands: ASME Turbo Expo; 2002, GT2002-30477.10.1115/GT2002-30477Search in Google Scholar
17. Taslim, ME, Bakhtari, K, Liu, H. Experimental and numerical investigation of impingement on a rib-roughened leading-edge wall. J Turbomach 2003;125:31–41, https://doi.org/10.1115/1.1624848.Search in Google Scholar
18. Quan, DL, Liu, SL, Li, JH, Liu, GW. Investigation on cooling performance of impingement cooling devices combined with pins. Reno-Tahoe, Nevada, USA: ASME Turbo Expo; 2005, GT2005-68930.10.1115/GT2005-68930Search in Google Scholar
19. Goldstein, RJ, Behbahani, AI. Impingement of a circular jet with and without crossflow. Int J Heat Mass Tran 1982;25:1377–82, https://doi.org/10.1016/0017-9310(82)90131-4.Search in Google Scholar
20. Adler, D, Baron, A. Prediction of a three-dimensional circular turbulent jet in crossflow. AIAA J 2015;17:168–74.10.2514/3.61091Search in Google Scholar
21. Yuan, LL, Street, RL. Trajectory and entrainment of a round jet in crossflow. Phys Fluids 1998;10:2323–35, https://doi.org/10.1063/1.869751.Search in Google Scholar
22. Smith, SH, Mungal, MG. Mixing, structure and scaling of the jet in crossflow. J Fluid Mech 1998;357:83–122, https://doi.org/10.1017/s0022112097007891.Search in Google Scholar
23. Plesniak, MW, Cusano, DM. Scalar mixing in a confined rectangular jet in crossflow. J Fluid Mech 2005;524:1–45, https://doi.org/10.1017/s0022112004001132.Search in Google Scholar
24. Meyer, KE, Pedersen, JM, Ozcan, O. A turbulent jet in crossflow analyzed with proper orthogonal decomposition. J Fluid Mech 2007;583:199–227, https://doi.org/10.1017/s0022112007006143.Search in Google Scholar
25. Ziefle, J, Kleiser, L. Large-eddy simulation of a round jet in crossflow. AIAA J 2009;47:1158–72, https://doi.org/10.2514/1.38465.Search in Google Scholar
26. Wu, Z, Laurence, D, Iacovides, H, Afgan, I. Direct simulation of conjugate heat transfer of jet in channel crossflow. Int J Heat Mass Tran 2017;110:193–208, https://doi.org/10.1016/j.ijheatmasstransfer.2017.03.027.Search in Google Scholar
27. Wu, Z, Laurence, D, Afgan, I. Direct numerical simulation of a low momentum round jet in channel crossflow. Nucl Eng Des 2017;313:273–84, https://doi.org/10.1016/j.nucengdes.2016.12.018.Search in Google Scholar
28. Florschuetz, LW, Metzger, DE, Truman, CR. Streamwise flow and heat transfer distributions for jet array impingement with crossflow. J Heat Tran 1981;103:337–42, https://doi.org/10.1115/1.3244463.Search in Google Scholar
29. Florschuetz, LW, Isoda, Y. Flow distributions and discharge coefficient effects for jet array impingement with initial crossflow. J Eng Gas Turbines Power 1983;105:296–304, https://doi.org/10.1115/1.3227415.Search in Google Scholar
30. Kang, LY, Zhang, JZ, Tan, XM. 3-D numerical computation of jet array impingement with initial crossflow. J Nanjing Univ Aeronaut Astronaut 2004;21:128–33.Search in Google Scholar
31. Lamont, JA, Ekkad, SV, Alvin, MA. Effects of rotation on heat transfer for a single row jet impingement array with crossflow. J Heat Tran 2012;134:1–12, https://doi.org/10.1115/1.4006167.Search in Google Scholar
32. Huang, YZ, Ekkad, SV, Han, JC. Detailed heat transfer distributions under an array of orthogonal impinging jets. J Thermophys Heat Tran 2012;12:73–9.10.2514/2.6304Search in Google Scholar
33. Huang, YZ, Ekkad, SV, Han, JC. Detailed heat transfer distributions under an array of inclined impinging jets using transient liquid crystal technique. In: 9th international symposium on transport phenomena in thermal fluids engineering, Singapore; 1996.10.1115/IMECE1996-0067Search in Google Scholar
34. Obot, NT, Trabold, TA. Impingement heat transfer within arrays of circular jets: part Ⅰ – effects of minimum, intermediate, and complete crossflow for small and large spacings. J Heat Tran 1987;109:872–9, https://doi.org/10.1115/1.3248197.Search in Google Scholar
35. Florschuetz, LW, Berry, RA, Metzger, DE. Periodic streamwise variations of heat transfer coefficients for inline and staggered arrays of circular jets with crossflow of spent air. J Heat Tran 1980;102:132–7, https://doi.org/10.1115/1.3244224.Search in Google Scholar
36. Chambers, AC, Gillespie, DRH, Ireland, PT, Dailey, GM. The effect of initial cross flow on the cooling performance of a narrow impingement channel. J Heat Tran 2005;127:358–65, https://doi.org/10.1115/1.1800493.Search in Google Scholar
37. Rao, AG, Belinkov, MK, Krapp, V, Levy, Y. Heat transfer investigations in multiple impinging jets at low Reynolds number. Glasgow, UK: ASME Turbo Expo; 2010, GT2010-22720.10.1115/GT2010-22720Search in Google Scholar
38. Paz, MLD, Jubran, BA. A numerical study of an impingement array inside a three dimensional turbine vane. Glasgow, UK: ASME Turbo Expo; 2010, GT2010-22270.Search in Google Scholar
39. Eroglu, A, Breidenthal, RE. Structure, penetration, and mixing of pulsed jets in crossflow. AIAA J 2001;39:417–23, https://doi.org/10.2514/3.14746.Search in Google Scholar
40. Yu, Y, Zhang, J, Shan, Y. Convective heat transfer of a row of air jets impingement excited by triangular tabs in a confined crossflow channel. Int J Heat Mass Tran 2015;80:126–38, https://doi.org/10.1016/j.ijheatmasstransfer.2014.08.066.Search in Google Scholar
41. Terzis, A, Ott, P, Cochet, M, Wolfersdorf, JV, Weigand, B. Effect of varying jet diameter on the heat transfer distributions of narrow impingement channels. J Turbomach 2016;138: 021004.Search in Google Scholar
42. Terzis, A, Ott, P, Cochet, M, Wolfersdorf, JV, Weigand, B. Aerothermal investigation of a single row divergent narrow impingement channel by particle image velocimetry and liquid crystal thermography. J Turbomach 2015;137: 051003, https://doi.org/10.1115/1.4028294.Search in Google Scholar
43. Esposito, EI, Ekkad, SV, Kim, Y, Dutta, P. Novel jet impingement cooling geometry for combustor liner backside cooling. J Therm Sci Eng Appl 2009;21: 021001, https://doi.org/10.1115/1.3202799.Search in Google Scholar
44. Esposito, EI, Kim, Y, Dutta, P. Comparing extended port and corrugated wall jet impingement geometry for combustor liner backside cooling. Montréal, Canada: ASME Turbo Expo; 2007, GT2007-27390.10.1115/GT2007-27390Search in Google Scholar
45. Chi, ZR, Kan, R, Ren, J, Jiang, HD. Experimental and numerical study of the anti-crossflow impingement cooling structure. Int J Heat Mass Tran 2013;64:567–80, https://doi.org/10.1016/j.ijheatmasstransfer.2013.04.052.Search in Google Scholar
46. Parida, PR, Ekkad, SV, Ngo, K. Experimental and numerical investigation of confined oblique impingement configurations for high heat flux applications. Int J Therm Sci 2011;50:1037–50, https://doi.org/10.1016/j.ijthermalsci.2011.01.010.Search in Google Scholar
47. Wang, L, Sundén, B, Borg, A, Abrahamsson, H. Control of jet impingement heat transfer in crossflow by using a rib. Int J Heat Mass Tran 2011;54:4157–66, https://doi.org/10.1016/j.ijheatmasstransfer.2011.06.004.Search in Google Scholar
48. Wang, CL, Wang, L, Sundén, B, Revstedt, J. Effects of a vortex generator pair on jet impingement heat transfer in cross-flow. Montréal, Canada: ASME Turbo Expo; 2015, GT2015-42236.10.1115/GT2015-42236Search in Google Scholar
49. Wang, CL, Luo, L, Wang, L, Sundén, B. Heat transfer and fluid flow of a single jet impingement in crossflow modified by a vortex generator pair. Seoul, South Korea: ASME Turbo Expo; 2016, GT2016-56894.10.1115/GT2016-56894Search in Google Scholar
50. Wang, CL, Wang, L, Sundén, B. A novel control of jet impingement heat transfer in cross-flow by a vortex generator pair. Int J Heat Mass Tran 2015;88:82–90, https://doi.org/10.1016/j.ijheatmasstransfer.2015.04.056.Search in Google Scholar
51. Wang, CL, Luo, L, Wang, L, Sundén, B. Effects of vortex generator on the jet impingement heat transfer at different cross-flow Reynolds number. Int J Heat Mass Tran 2016;96:278–86, https://doi.org/10.1016/j.ijheatmasstransfer.2016.01.042.Search in Google Scholar
52. Madhavan, S, Ramakrishnan, KR, Singh, P, Ekkad, S. Jet impingement heat transfer enhancement by U-shaped crossflow diverters. J Therm Sci Eng Appl 2020;12: 041005, https://doi.org/10.1115/1.4045514.Search in Google Scholar
53. Liu, KX, Zhang, Q. A novel multi-stage impingement cooling scheme-part I: concept study. J Turbomach 2020;142:121008, https://doi.org/10.1115/1.4048183.Search in Google Scholar
54. Liu, KX, Zhang, Q. A novel multi-stage impingement cooling scheme-part II: design optimization. J Turbomach 2020;142:121009, https://doi.org/10.1115/1.4048184.Search in Google Scholar
55. Florschuetz, LW, Metzger, DE, Su, CC. Heat transfer characteristics for jet array impingement with initial crossflow. J Heat Tran 1984;106:34–41, https://doi.org/10.1115/1.3246656.Search in Google Scholar
© 2022 Walter de Gruyter GmbH, Berlin/Boston
Articles in the same Issue
- Frontmatter
- The International Journal of Turbo and Jet Engines
- The aerothermodynamic cycle optimal design of a turbofan engine
- Multi-condition design optimization of groove flow control technique in an axial-flow pump
- Analysis on impulse characteristics of pulse detonation engine with nozzles
- Numerical investigation on implication of innovative hydrogen strut injector on performance and combustion characteristics in a scramjet combustor
- Optimization of Kiel geometry for better recovery factor in high temperature measurement in aero gas turbine engine
- Applicability of correlational data-mining to small-scale turbojet performance map generation
- Effect of multi-zone effusion cooling on an adiabatic flat plate for gas turbine application
- Flow quality improvement of the wind tunnel testing for a highly-loaded compressor cascade at high incidence
- Modeling and analysis of 3D radiative heat transfer in combustor
- A creep-fatigue life prediction model considering multi-factor coupling effect
- Optimization-based transient control of turbofan engines: a sequential quadratic programming approach
- Investigations on the interaction between the front and aft purge flow and the downstream vane of 1.5-stage turbine
- A study on design optimization for compressor blisks
- Exploration of an unconventional validation tool to investigate aero engine transonic fan flutter signature
- Evaluation of non-uniform water film behavior on the performance of an axial aeroengine compressor
- Predicting remaining useful life of turbofan engines using degradation signal based echo state network
- Effect of G-type integral squeeze film damper on the dynamic characteristics in rotor system
- Development of a one-dimensional code for the initial design of a micro gas turbine mixed flow compressor stage
- Numerical and experimental investigations of tip clearance effects in a high-flow-coefficient centrifugal compressor
- Experimental and numerical investigation on the effect of turboprop engine exhaust gas impingement on pusher aircraft
- Heat transfer distribution of single oblique jet impingement in crossflow under different inlet conditions
- Performance enhancement and flow separation control in an S-duct by air injection
- Gas dynamic analysis of the modern single shaft gas turbine engine flow path
- Aero engine health monitoring, diagnostics and prognostics for condition-based maintenance: an overview
- Influence of leading edge point on aerodynamic performance of asymmetric leading edge compressor airfoils
- The aerothermal performance of turbine blade squealer tip at various Reynolds numbers and Mach numbers with moving endwall
- Numerical investigation of a variable stator vane with nonuniform partial radial gaps in an annular compressor cascade
- Effect of self-recirculating casing treatment on the unsteady flow and stability of counter-rotating axial-flow compressor
- Research on temperature rise characteristics of end V-groove ring seal
- Research on the influence of honeycomb cell blockage on the seal leakage characteristics
- Vortex structure control based bleed in axial compressor cascade with tip clearance using large eddy simulation
- Development and application of a profile loss model considering the low-Re effect in low-pressure turbine
- Optimization of ACE mode transition control schedule considering geometric adjustment speed
- Numerical investigation of flow control in low-pressure turbine cascade using Gurney Flaps
- The design method of the V-shaped groove piston ring
- Control of subsonic jets using vanes as vortex generators
- Impact investigation of inlet environmental changes on the rated condition performance of a high-pressure compressor
- Research on new integral squeeze film damper vibration control of micro turbojet engine at high speed
- Effect of the distribution of the upstream probe support on performance of compressor cascade
- Effect of bypass ratio on sonic underexpanded co-flow jets with finite lip thickness
- Machine learning augmented multi-sensor data fusion to detect aero engine fan rotor blade flutter
- CFD analysis of flow control in compressor cascade using MVGs
- Quantitative investigation of the evaporation and resistance characteristics of inlet jet precooling
- Study on laser de-weight and dynamic balance technology of rotating machines
- Integrated design and analysis of inlet and missile with two side layout
- Research on turboprop engine control method based on linear parameter varying model
- Modeling and validation of the volume effect on the axial fan transient performance
- Ground effects on the aerodynamics of a wing with slot type distributed propulsion system for VTOL applications
- Multidisciplinary sensitivity analysis for turbine blade considering thickness uncertainties
- Accurate measurement and evaluation method of axial compressor efficiency under the influence of multiple factors
- Control mechanism of secondary flow in a turbine cascade with non-axisymmetric endwall profiling under Co-rotating incoming vortex
- Infrared simulation of aircraft rear fuselage based on a coupled CFD method
- Effect of multi-hole trench cooling on an adiabatic flat plate for gas turbine application
- Numerical study of transition process in different zones of a compressor cascade channel
Articles in the same Issue
- Frontmatter
- The International Journal of Turbo and Jet Engines
- The aerothermodynamic cycle optimal design of a turbofan engine
- Multi-condition design optimization of groove flow control technique in an axial-flow pump
- Analysis on impulse characteristics of pulse detonation engine with nozzles
- Numerical investigation on implication of innovative hydrogen strut injector on performance and combustion characteristics in a scramjet combustor
- Optimization of Kiel geometry for better recovery factor in high temperature measurement in aero gas turbine engine
- Applicability of correlational data-mining to small-scale turbojet performance map generation
- Effect of multi-zone effusion cooling on an adiabatic flat plate for gas turbine application
- Flow quality improvement of the wind tunnel testing for a highly-loaded compressor cascade at high incidence
- Modeling and analysis of 3D radiative heat transfer in combustor
- A creep-fatigue life prediction model considering multi-factor coupling effect
- Optimization-based transient control of turbofan engines: a sequential quadratic programming approach
- Investigations on the interaction between the front and aft purge flow and the downstream vane of 1.5-stage turbine
- A study on design optimization for compressor blisks
- Exploration of an unconventional validation tool to investigate aero engine transonic fan flutter signature
- Evaluation of non-uniform water film behavior on the performance of an axial aeroengine compressor
- Predicting remaining useful life of turbofan engines using degradation signal based echo state network
- Effect of G-type integral squeeze film damper on the dynamic characteristics in rotor system
- Development of a one-dimensional code for the initial design of a micro gas turbine mixed flow compressor stage
- Numerical and experimental investigations of tip clearance effects in a high-flow-coefficient centrifugal compressor
- Experimental and numerical investigation on the effect of turboprop engine exhaust gas impingement on pusher aircraft
- Heat transfer distribution of single oblique jet impingement in crossflow under different inlet conditions
- Performance enhancement and flow separation control in an S-duct by air injection
- Gas dynamic analysis of the modern single shaft gas turbine engine flow path
- Aero engine health monitoring, diagnostics and prognostics for condition-based maintenance: an overview
- Influence of leading edge point on aerodynamic performance of asymmetric leading edge compressor airfoils
- The aerothermal performance of turbine blade squealer tip at various Reynolds numbers and Mach numbers with moving endwall
- Numerical investigation of a variable stator vane with nonuniform partial radial gaps in an annular compressor cascade
- Effect of self-recirculating casing treatment on the unsteady flow and stability of counter-rotating axial-flow compressor
- Research on temperature rise characteristics of end V-groove ring seal
- Research on the influence of honeycomb cell blockage on the seal leakage characteristics
- Vortex structure control based bleed in axial compressor cascade with tip clearance using large eddy simulation
- Development and application of a profile loss model considering the low-Re effect in low-pressure turbine
- Optimization of ACE mode transition control schedule considering geometric adjustment speed
- Numerical investigation of flow control in low-pressure turbine cascade using Gurney Flaps
- The design method of the V-shaped groove piston ring
- Control of subsonic jets using vanes as vortex generators
- Impact investigation of inlet environmental changes on the rated condition performance of a high-pressure compressor
- Research on new integral squeeze film damper vibration control of micro turbojet engine at high speed
- Effect of the distribution of the upstream probe support on performance of compressor cascade
- Effect of bypass ratio on sonic underexpanded co-flow jets with finite lip thickness
- Machine learning augmented multi-sensor data fusion to detect aero engine fan rotor blade flutter
- CFD analysis of flow control in compressor cascade using MVGs
- Quantitative investigation of the evaporation and resistance characteristics of inlet jet precooling
- Study on laser de-weight and dynamic balance technology of rotating machines
- Integrated design and analysis of inlet and missile with two side layout
- Research on turboprop engine control method based on linear parameter varying model
- Modeling and validation of the volume effect on the axial fan transient performance
- Ground effects on the aerodynamics of a wing with slot type distributed propulsion system for VTOL applications
- Multidisciplinary sensitivity analysis for turbine blade considering thickness uncertainties
- Accurate measurement and evaluation method of axial compressor efficiency under the influence of multiple factors
- Control mechanism of secondary flow in a turbine cascade with non-axisymmetric endwall profiling under Co-rotating incoming vortex
- Infrared simulation of aircraft rear fuselage based on a coupled CFD method
- Effect of multi-hole trench cooling on an adiabatic flat plate for gas turbine application
- Numerical study of transition process in different zones of a compressor cascade channel
