Integrated design and analysis of inlet and missile with two side layout
-
Fuzhou Liu
,
Jun Liu
Abstract
Based on the flow field characteristics of the missile body, an integrated design method for missile and inlet with two side layout is proposed under asymmetric inflow. The result of numerical simulation shows that shock waves hit on cowl lip on the symmetry plane at the design condition, which verifies the method of integrated design. And the flow characteristics of inlet under the influence of the missile body are analyzed. Under the influence of asymmetric incoming flow and missile body, the first shock wave surface of the two-dimensional inlet presents the characteristics of a three-dimensional concave surface, and there is a pair of asymmetric vortex structures in the inner flow path. Finally, a bleed cavity of self-adaptively adjusting bleeding by vortex is proposed to improve the performance of inlet and broaden the inlet start and attack angle boundary. The minimum Mach number of the inlet start is reduced from 2.8 to 2.3 at ɑ = 6° and the maximum attack angle of inlet start is widened from ɑ = −1° to ɑ = 3° at Ma = 2.1.
Acknowledgments
This study was co-supported by the National Natural Science Foundation of China (No. 11772155) and the Aviation Foundation of China (No. 20200012052001).
-
Author contribution: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Research funding: None declared.
-
Conflict of interest statement: The authors declare no conflicts of interest regarding this article.
References
1. Moses, PL, Rausch, VL, Nguyen, LT, Hill, JR. NASA hypersonic flight demonstrators-overview, status, and future plans. Acta Astronaut 2004;55:619–30. https://doi.org/10.1016/j.actaastro.2004.05.045.Search in Google Scholar
2. Yang, SB. Optimal control of ramjet engines for airframe propulsion integrated system [dissertation]. Harbin: Harbin Institute of Technology; 2017.Search in Google Scholar
3. Bricalli, MG, Brown, LM, Boyce, RR. Numerical investigation into the combustion behavior of an inlet fueled thermal compression like scramjet. AIAA J 2015;53:1740–60. https://doi.org/10.2514/1.j053513.Search in Google Scholar
4. Zhao, KY. An experimental investigation on aft bypass supersonic inlet performance at high angle of attack and yaw. J Propuls Technol 1992;13:47–52.Search in Google Scholar
5. Moore, M, Jenn, A. Preliminary design aerodynamics of missile inlets. In: Flight simulation technologies conference and exhibit; 1990 Sep 17–19. Dayton, USA, Reston: AIAA; 1990.10.2514/6.1990-3091Search in Google Scholar
6. Cai, FC. Study of Inlets/body Aerodynamic Interference of Supersonic Tactical Missile Using Numerical Simulation [dissertation]. Xi’an: Northwestern Polytechnical University; 2005.Search in Google Scholar
7. Satyanarayana, A, Theerthamalai, P, Santhakumar, S. Computational aerodynamic study of body-intake configurations. In: 44th AIAA aerospace sciences meeting and exhibit;2006 Jan 09-12. Reno, USA, Reston: AIAA; 2006.10.2514/6.2006-861Search in Google Scholar
8. Jiang, N, Wang, YW, Ling, WH, Wang, J. Integration performance analysis of typical arrangement inlet/missile. J Propuls Technol 2011;32:451–4.Search in Google Scholar
9. Li, XP, Yang, M. Numerical study of inlet configuration effects on aerodynamic performance for air-breathing missile. Sci Technol Eng 2010;10:8747–51.Search in Google Scholar
10. Xie, WZ, Guo, RW. Mixed-compression supersonic inlets based on four air-breathing aircraft configurations. J Nanjing Univ Aeronaut Astronaut 2011;43:13–7.Search in Google Scholar
11. Meng, YP, Zheng, RH. Brief review on inlet of the supersonic flow and integrated development of winged missiles. Aerospace Technology 2008;277:47–52.Search in Google Scholar
12. Zheng, RS, Li, WP, Chang, JT, Cui, DF, Man, YJ, Zhu, SM, et al.. Suppression of interaction between shock wave and boundary layer for “X” hypersonic inverted inlet. J Propuls Technol 2014;35:1153–61.Search in Google Scholar
13. Luo, H, Jin, ZG, Zhang, KY. Aerodynamic performance comparison of a two-dimensional inlet for missile in an inverted “X”-type layout with classical layout. J Aero Power 2019;34:2366–76.Search in Google Scholar
14. Cao, JW. Effects of two-dimensional inlet configuration and compression surface position on the performance of inlet based on ramjet engine. Aero Weaponry 2008;246:44–7.Search in Google Scholar
15. Ostrander, M, Thomas, M, Clegern, J. Inlet analysis for ATR-powered supersonic missile. In: 31st joint propulsion conference and exhibit;1995 Jul 10–12. San Diego, USA, Reston: AIAA; 1995.10.2514/6.1995-2805Search in Google Scholar
16. Xie, LR, Guo, RW. Flow pattern and performance of fixed-geometry two-dimensional mixed-compression supersonic inlets with 90° configuration at the venter of the missile. Acta Aerodyn Sin 2011;29:257–63.Search in Google Scholar
17. Xie, LR, Guo, RW. Experimental investigation of fixed-geometry two-dimensional mixed-compression supersonic inlet with twin-inlet 90° configuration at venter. Acta Aeronautica Astronautica Sinica 2009;30:1000–6.Search in Google Scholar
18. Tokunaga, H, Koori, K, Ikegami, Y, Sato, J, Yoshida, A. Development of wide-range supersonic intake for variable flow ducted rocket engine. In: 45th AIAA/ASME/SAE/ASEE joint propulsion conference & exhibit;2009 Aug 02–05. Denver, USA Reston: AIAA; 2009.10.2514/6.2009-5223Search in Google Scholar
19. Ma, XF, Xie, LR, Guo, RW. Investigation of two-dimensional supersonic twin inlet with slot coupled cavity in 90° configuration at venter. J Aero Power 2010;25:1818–24.Search in Google Scholar
20. Yang, YX, Chen, Y, Dong, XG. Unstart-restart characteristics analysis of 2-D mixing compression inlets with configuration of 90° on both downsides. J Solid Rocket Technol 2017;40:691–7.Search in Google Scholar
21. Matsuo, K, Miyazato, Y, Kim, HD. Shock train and pseudo-shock phenomena in internal gas flows. Prog Aero Sci 1999;35:33–100. https://doi.org/10.1016/s0376-0421(98)00011-6.Search in Google Scholar
© 2022 Walter de Gruyter GmbH, Berlin/Boston
Articles in the same Issue
- Frontmatter
- The International Journal of Turbo and Jet Engines
- The aerothermodynamic cycle optimal design of a turbofan engine
- Multi-condition design optimization of groove flow control technique in an axial-flow pump
- Analysis on impulse characteristics of pulse detonation engine with nozzles
- Numerical investigation on implication of innovative hydrogen strut injector on performance and combustion characteristics in a scramjet combustor
- Optimization of Kiel geometry for better recovery factor in high temperature measurement in aero gas turbine engine
- Applicability of correlational data-mining to small-scale turbojet performance map generation
- Effect of multi-zone effusion cooling on an adiabatic flat plate for gas turbine application
- Flow quality improvement of the wind tunnel testing for a highly-loaded compressor cascade at high incidence
- Modeling and analysis of 3D radiative heat transfer in combustor
- A creep-fatigue life prediction model considering multi-factor coupling effect
- Optimization-based transient control of turbofan engines: a sequential quadratic programming approach
- Investigations on the interaction between the front and aft purge flow and the downstream vane of 1.5-stage turbine
- A study on design optimization for compressor blisks
- Exploration of an unconventional validation tool to investigate aero engine transonic fan flutter signature
- Evaluation of non-uniform water film behavior on the performance of an axial aeroengine compressor
- Predicting remaining useful life of turbofan engines using degradation signal based echo state network
- Effect of G-type integral squeeze film damper on the dynamic characteristics in rotor system
- Development of a one-dimensional code for the initial design of a micro gas turbine mixed flow compressor stage
- Numerical and experimental investigations of tip clearance effects in a high-flow-coefficient centrifugal compressor
- Experimental and numerical investigation on the effect of turboprop engine exhaust gas impingement on pusher aircraft
- Heat transfer distribution of single oblique jet impingement in crossflow under different inlet conditions
- Performance enhancement and flow separation control in an S-duct by air injection
- Gas dynamic analysis of the modern single shaft gas turbine engine flow path
- Aero engine health monitoring, diagnostics and prognostics for condition-based maintenance: an overview
- Influence of leading edge point on aerodynamic performance of asymmetric leading edge compressor airfoils
- The aerothermal performance of turbine blade squealer tip at various Reynolds numbers and Mach numbers with moving endwall
- Numerical investigation of a variable stator vane with nonuniform partial radial gaps in an annular compressor cascade
- Effect of self-recirculating casing treatment on the unsteady flow and stability of counter-rotating axial-flow compressor
- Research on temperature rise characteristics of end V-groove ring seal
- Research on the influence of honeycomb cell blockage on the seal leakage characteristics
- Vortex structure control based bleed in axial compressor cascade with tip clearance using large eddy simulation
- Development and application of a profile loss model considering the low-Re effect in low-pressure turbine
- Optimization of ACE mode transition control schedule considering geometric adjustment speed
- Numerical investigation of flow control in low-pressure turbine cascade using Gurney Flaps
- The design method of the V-shaped groove piston ring
- Control of subsonic jets using vanes as vortex generators
- Impact investigation of inlet environmental changes on the rated condition performance of a high-pressure compressor
- Research on new integral squeeze film damper vibration control of micro turbojet engine at high speed
- Effect of the distribution of the upstream probe support on performance of compressor cascade
- Effect of bypass ratio on sonic underexpanded co-flow jets with finite lip thickness
- Machine learning augmented multi-sensor data fusion to detect aero engine fan rotor blade flutter
- CFD analysis of flow control in compressor cascade using MVGs
- Quantitative investigation of the evaporation and resistance characteristics of inlet jet precooling
- Study on laser de-weight and dynamic balance technology of rotating machines
- Integrated design and analysis of inlet and missile with two side layout
- Research on turboprop engine control method based on linear parameter varying model
- Modeling and validation of the volume effect on the axial fan transient performance
- Ground effects on the aerodynamics of a wing with slot type distributed propulsion system for VTOL applications
- Multidisciplinary sensitivity analysis for turbine blade considering thickness uncertainties
- Accurate measurement and evaluation method of axial compressor efficiency under the influence of multiple factors
- Control mechanism of secondary flow in a turbine cascade with non-axisymmetric endwall profiling under Co-rotating incoming vortex
- Infrared simulation of aircraft rear fuselage based on a coupled CFD method
- Effect of multi-hole trench cooling on an adiabatic flat plate for gas turbine application
- Numerical study of transition process in different zones of a compressor cascade channel
Articles in the same Issue
- Frontmatter
- The International Journal of Turbo and Jet Engines
- The aerothermodynamic cycle optimal design of a turbofan engine
- Multi-condition design optimization of groove flow control technique in an axial-flow pump
- Analysis on impulse characteristics of pulse detonation engine with nozzles
- Numerical investigation on implication of innovative hydrogen strut injector on performance and combustion characteristics in a scramjet combustor
- Optimization of Kiel geometry for better recovery factor in high temperature measurement in aero gas turbine engine
- Applicability of correlational data-mining to small-scale turbojet performance map generation
- Effect of multi-zone effusion cooling on an adiabatic flat plate for gas turbine application
- Flow quality improvement of the wind tunnel testing for a highly-loaded compressor cascade at high incidence
- Modeling and analysis of 3D radiative heat transfer in combustor
- A creep-fatigue life prediction model considering multi-factor coupling effect
- Optimization-based transient control of turbofan engines: a sequential quadratic programming approach
- Investigations on the interaction between the front and aft purge flow and the downstream vane of 1.5-stage turbine
- A study on design optimization for compressor blisks
- Exploration of an unconventional validation tool to investigate aero engine transonic fan flutter signature
- Evaluation of non-uniform water film behavior on the performance of an axial aeroengine compressor
- Predicting remaining useful life of turbofan engines using degradation signal based echo state network
- Effect of G-type integral squeeze film damper on the dynamic characteristics in rotor system
- Development of a one-dimensional code for the initial design of a micro gas turbine mixed flow compressor stage
- Numerical and experimental investigations of tip clearance effects in a high-flow-coefficient centrifugal compressor
- Experimental and numerical investigation on the effect of turboprop engine exhaust gas impingement on pusher aircraft
- Heat transfer distribution of single oblique jet impingement in crossflow under different inlet conditions
- Performance enhancement and flow separation control in an S-duct by air injection
- Gas dynamic analysis of the modern single shaft gas turbine engine flow path
- Aero engine health monitoring, diagnostics and prognostics for condition-based maintenance: an overview
- Influence of leading edge point on aerodynamic performance of asymmetric leading edge compressor airfoils
- The aerothermal performance of turbine blade squealer tip at various Reynolds numbers and Mach numbers with moving endwall
- Numerical investigation of a variable stator vane with nonuniform partial radial gaps in an annular compressor cascade
- Effect of self-recirculating casing treatment on the unsteady flow and stability of counter-rotating axial-flow compressor
- Research on temperature rise characteristics of end V-groove ring seal
- Research on the influence of honeycomb cell blockage on the seal leakage characteristics
- Vortex structure control based bleed in axial compressor cascade with tip clearance using large eddy simulation
- Development and application of a profile loss model considering the low-Re effect in low-pressure turbine
- Optimization of ACE mode transition control schedule considering geometric adjustment speed
- Numerical investigation of flow control in low-pressure turbine cascade using Gurney Flaps
- The design method of the V-shaped groove piston ring
- Control of subsonic jets using vanes as vortex generators
- Impact investigation of inlet environmental changes on the rated condition performance of a high-pressure compressor
- Research on new integral squeeze film damper vibration control of micro turbojet engine at high speed
- Effect of the distribution of the upstream probe support on performance of compressor cascade
- Effect of bypass ratio on sonic underexpanded co-flow jets with finite lip thickness
- Machine learning augmented multi-sensor data fusion to detect aero engine fan rotor blade flutter
- CFD analysis of flow control in compressor cascade using MVGs
- Quantitative investigation of the evaporation and resistance characteristics of inlet jet precooling
- Study on laser de-weight and dynamic balance technology of rotating machines
- Integrated design and analysis of inlet and missile with two side layout
- Research on turboprop engine control method based on linear parameter varying model
- Modeling and validation of the volume effect on the axial fan transient performance
- Ground effects on the aerodynamics of a wing with slot type distributed propulsion system for VTOL applications
- Multidisciplinary sensitivity analysis for turbine blade considering thickness uncertainties
- Accurate measurement and evaluation method of axial compressor efficiency under the influence of multiple factors
- Control mechanism of secondary flow in a turbine cascade with non-axisymmetric endwall profiling under Co-rotating incoming vortex
- Infrared simulation of aircraft rear fuselage based on a coupled CFD method
- Effect of multi-hole trench cooling on an adiabatic flat plate for gas turbine application
- Numerical study of transition process in different zones of a compressor cascade channel
