Twin-roll cast Al–Mg –Si sheet for automotive applications
-
Yücel Birol
Abstract
Twin-roll casting (TRC) is well established as an economical method for producing aluminum foil and sheet for various applications. Recently, there has been an increasing interest in using TRC as a method to produce low-cost/high-quality aluminum sheet for automotive structural applications. The potential of TRC process in the manufacture of AA5XXX sheet for automotive structural applications has recently been demonstrated. The present work was undertaken to implement TRC technology and to develop processing cycles for the manufacture of twin-roll cast AA6016 sheet for inner and outer panel applications.
-
It is a pleasure to thank Selda Üçüncüogğlu, Fahri Alageyik and Osman Çakır of Marmara Research Center for their help in the experimental part of this work, and ASSAN Aluminium for supplying the TRC 6016 strip and for performing the tensile tests. The financial support of TİDEB-TÜBİTAK is gratefully acknowledged.
References
[1] S.B. Kang, H.W. Kim, D. Jiang, K.W. Nam, S.T. Lee: T. Sato, S. Kunai, T. Kobayashi, Y. Murakami (Eds.), Proc. ICAA-6 (1998) 1331.Suche in Google Scholar
[2] T. Naka, F. Yoshida: ibid., 455.Suche in Google Scholar
[3] A. Morita: ibid., 25.Suche in Google Scholar
[4] K.R. Brown, M.S. Veine, R.A. Woods: JOM 47 (1995) 20.10.1007/BF03221224Suche in Google Scholar
[5] A.S. Warren: Aluminium 67 (1991) 1078.10.1136/pgmj.67.794.1078Suche in Google Scholar
[6] J. Sarkar, T.R.G. Kutty, D.S. Wilkinson, J.D. Embury, D.J. Lloyd: Materials Science Forum 331–337 (2000) 583.10.4028/www.scientific.net/MSF.331-337.583Suche in Google Scholar
[7] T. Moons, P. Ratchev, P. DeSmet, B. Verlinden, P. Van Houte: Scripta Mater., 35 (1996) 939.10.1016/1359-6462(96)00244-8Suche in Google Scholar
[8] G. Burger, A.K. Gupta, L. Sutak, D.J. Lloyd: Materials Science Forum 217–222 (1996) 471.10.4028/www.scientific.net/MSF.217-222.471Suche in Google Scholar
[9] L. Zhuang, R. de Haan, J. Bottema, C.T.W. Lahaye, P. De Smet: Materials Science Forum 331–337 (2000) 1309.10.4028/www.scientific.net/MSF.331-337.1309Suche in Google Scholar
[10] X.G. Chen, J. Langlais: ibid., 215.Suche in Google Scholar
[11] A. Perovic, D.D. Perovic, G.C. Weatherly, D.J. Lloyd: Scripta Mater. 41 (1999) 703.10.1016/S1359-6462(99)00204-3Suche in Google Scholar
[12] W.S. Miller, L. Zhuang, J. Bottema, A.J. Wittebrood, P. De Smet, A. Haszler, A.Vieregge: Mater. Sci. Eng. A 280 (2000) 37.10.1016/S0921-5093(99)00653-XSuche in Google Scholar
[13] J. Hirsch: Materials Science Forum 242 (1997) 33.10.4028/www.scientific.net/MSF.242.33Suche in Google Scholar
[14] G.L. McVay, E.L. Courtright, R.H. Jones, M.T. Smith: Light Metal Age 56 (1998) 6.Suche in Google Scholar
[15] A.M. Sherman, R.G. Davies, V.C. Shah, S. Kim, W.K. Miller, in: J. Evans (Ed.), Light Metals, TMS (1995) 1145.Suche in Google Scholar
[16] Y. Birol, G. Kara, M. Dündar, O. Çakır, G. Zeybekogğlu, A. Akkurt, G. Yıldızbayrak, C. Romanowski, in: S.K. Das (Ed.), Automotive Alloys 2001, The Minerals, Metals & Materials Society (2001) 107.Suche in Google Scholar
[17] M. Slamova, Y. Birol, M. Dündar, A.S. Akkurt: Materials Science Forum 396–402 (2002) 711.10.4028/www.scientific.net/MSF.396-402.711Suche in Google Scholar
[18] M. Dündar, Y. Birol, A.S. Akkurt: ibid., 1647.Suche in Google Scholar
© 2004 Carl Hanser Verlag, München
Artikel in diesem Heft
- Frontmatter
- Editorial
- Challenges and interesting observations associated with feedback-controlled nanoindentation
- Nanoscratching on surfaces: the relationships between lateral force, normal force and normal displacement
- Nano-scratch testing on thin diamond-like carbon coatings for microactuators: friction, wear and elastic-plastic deformation
- Comparison of hardness and Young’s modulus by single indentation and multiple unloading indentation
- Nanomechanical characterization of Ti-base nanostructure-dendrite composite
- Surface topography and nanomechanical/tribological behaviour of ultrathin nitride films on silicon
- Viscosity of glass at high contact pressure during indentation experiments
- Dynamic indentation measurements on amorphous materials
- Technique for measuring the residual strain in strained Si/SiGe MOSFET structures using Raman spectroscopy
- Partial atomic volumes of early transition metals in A10 metal-based solid solutions
- Effects of an external electric field applied during the solution heat treatment of the Al-Mg-Si-Cu alloy AA6111
- Fatigue crack propagation in pseudoelastic TiNi smart microcomponents
- Microstructure evolution in immiscible alloys during rapid directional solidification
- The creep performance of a sand-cast Mg–2.8 Nd–0.8 Zn–0.5 Zr–0.3 Gd alloy at 241 to 262°C
- Punch-shear tests and size effects for evaluating the shear strength of machinable ceramics
- Study of Ti–Si in situ composite processing by multi-stage eutectic solidification
- Twin-roll cast Al–Mg –Si sheet for automotive applications
- Thermodynamics and surface properties of Fe–V and Fe–Ti liquid alloys
- Personal/ Personelles
- Press/ Presse
- Books/Bücher
- Conferences / Konferenzen
- Frontmatter
- Editorial
- Editorial
- Articles Basic
- Challenges and interesting observations associated with feedback-controlled nanoindentation
- Nanoscratching on surfaces: the relationships between lateral force, normal force and normal displacement
- Nano-scratch testing on thin diamond-like carbon coatings for microactuators: friction, wear and elastic-plastic deformation
- Comparison of hardness and Young’s modulus by single indentation and multiple unloading indentation
- Nanomechanical characterization of Ti-base nanostructure-dendrite composite
- Surface topography and nanomechanical/tribological behaviour of ultrathin nitride films on silicon
- Viscosity of glass at high contact pressure during indentation experiments
- Dynamic indentation measurements on amorphous materials
- Technique for measuring the residual strain in strained Si/SiGe MOSFET structures using Raman spectroscopy
- Partial atomic volumes of early transition metals in A10 metal-based solid solutions
- Effects of an external electric field applied during the solution heat treatment of the Al-Mg-Si-Cu alloy AA6111
- Fatigue crack propagation in pseudoelastic TiNi smart microcomponents
- Microstructure evolution in immiscible alloys during rapid directional solidification
- The creep performance of a sand-cast Mg–2.8 Nd–0.8 Zn–0.5 Zr–0.3 Gd alloy at 241 to 262°C
- Articles Applied
- Punch-shear tests and size effects for evaluating the shear strength of machinable ceramics
- Study of Ti–Si in situ composite processing by multi-stage eutectic solidification
- Twin-roll cast Al–Mg –Si sheet for automotive applications
- Thermodynamics and surface properties of Fe–V and Fe–Ti liquid alloys
- Notifications/Mitteilungen
- Personal/ Personelles
- Books/Bücher
- Press/ Presse
- Conferences / Konferenzen
Artikel in diesem Heft
- Frontmatter
- Editorial
- Challenges and interesting observations associated with feedback-controlled nanoindentation
- Nanoscratching on surfaces: the relationships between lateral force, normal force and normal displacement
- Nano-scratch testing on thin diamond-like carbon coatings for microactuators: friction, wear and elastic-plastic deformation
- Comparison of hardness and Young’s modulus by single indentation and multiple unloading indentation
- Nanomechanical characterization of Ti-base nanostructure-dendrite composite
- Surface topography and nanomechanical/tribological behaviour of ultrathin nitride films on silicon
- Viscosity of glass at high contact pressure during indentation experiments
- Dynamic indentation measurements on amorphous materials
- Technique for measuring the residual strain in strained Si/SiGe MOSFET structures using Raman spectroscopy
- Partial atomic volumes of early transition metals in A10 metal-based solid solutions
- Effects of an external electric field applied during the solution heat treatment of the Al-Mg-Si-Cu alloy AA6111
- Fatigue crack propagation in pseudoelastic TiNi smart microcomponents
- Microstructure evolution in immiscible alloys during rapid directional solidification
- The creep performance of a sand-cast Mg–2.8 Nd–0.8 Zn–0.5 Zr–0.3 Gd alloy at 241 to 262°C
- Punch-shear tests and size effects for evaluating the shear strength of machinable ceramics
- Study of Ti–Si in situ composite processing by multi-stage eutectic solidification
- Twin-roll cast Al–Mg –Si sheet for automotive applications
- Thermodynamics and surface properties of Fe–V and Fe–Ti liquid alloys
- Personal/ Personelles
- Press/ Presse
- Books/Bücher
- Conferences / Konferenzen
- Frontmatter
- Editorial
- Editorial
- Articles Basic
- Challenges and interesting observations associated with feedback-controlled nanoindentation
- Nanoscratching on surfaces: the relationships between lateral force, normal force and normal displacement
- Nano-scratch testing on thin diamond-like carbon coatings for microactuators: friction, wear and elastic-plastic deformation
- Comparison of hardness and Young’s modulus by single indentation and multiple unloading indentation
- Nanomechanical characterization of Ti-base nanostructure-dendrite composite
- Surface topography and nanomechanical/tribological behaviour of ultrathin nitride films on silicon
- Viscosity of glass at high contact pressure during indentation experiments
- Dynamic indentation measurements on amorphous materials
- Technique for measuring the residual strain in strained Si/SiGe MOSFET structures using Raman spectroscopy
- Partial atomic volumes of early transition metals in A10 metal-based solid solutions
- Effects of an external electric field applied during the solution heat treatment of the Al-Mg-Si-Cu alloy AA6111
- Fatigue crack propagation in pseudoelastic TiNi smart microcomponents
- Microstructure evolution in immiscible alloys during rapid directional solidification
- The creep performance of a sand-cast Mg–2.8 Nd–0.8 Zn–0.5 Zr–0.3 Gd alloy at 241 to 262°C
- Articles Applied
- Punch-shear tests and size effects for evaluating the shear strength of machinable ceramics
- Study of Ti–Si in situ composite processing by multi-stage eutectic solidification
- Twin-roll cast Al–Mg –Si sheet for automotive applications
- Thermodynamics and surface properties of Fe–V and Fe–Ti liquid alloys
- Notifications/Mitteilungen
- Personal/ Personelles
- Books/Bücher
- Press/ Presse
- Conferences / Konferenzen
