Home Technology Metallurgical and wear study of MWCNT-reinforced h-AMMC fabricated through microwave hybrid sintering
Article
Licensed
Unlicensed Requires Authentication

Metallurgical and wear study of MWCNT-reinforced h-AMMC fabricated through microwave hybrid sintering

  • Rajat Kumar , Hiralal Bhowmick EMAIL logo and Dheeraj Gupta
Published/Copyright: March 22, 2021
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 112 Issue 3

Abstract

The present work deals with the outcomes of a novel approach for developing a multi-walled carbon nanotube-reinforced hybrid aluminium metal matrix composite. Microwave hybrid sintering in combination with cold compaction of the powder metallurgy route was followed for the fabrication of composites. Microwave hybrid sintering was carried out using a microwave oven operating at 2.45 GHz frequency and 900 W power. For this purpose, Al5083 was used as the matrix material, and silicon carbide (15 wt.%) and multi-walled carbon nanotubes (0.5 wt.%) the reinforcements. The fabricated composites were then characterized by hardness, microstructure, and porosity. An investigation on the wear resistance of the base alloy and the conventional and microwave sintered composites followed this. The findings of the present study reveal the fact that the addition of carbon nano-tubes in the composite and the use of microwave energy over conventional sintering have a significant effect on the property enhancement of the developed hybrid composite.

Keywords: Hybrid aluminium metal matrix composite; Microwave; Sintering; Carbon nanotube; Wear
Dr. Hiralal Bhowmick, Associate Professor Mechanical Engineering Department Thapar Institute of Engineering and Technology Patiala-147004 India Tel.: +91 9972817423

References

[1] G. Ramakrishnan, B.V. Ramnath, E. Naveen, S. Gowtham, A.A. Kumar, M.S. Muthuvel, R. Akil: Adv. Sci. Eng. Med. 10 (2018) 263. DOI:10.1166/asem.2018.216310.1166/asem.2018.2163Search in Google Scholar

[2] J.R. Davis (Ed): Alloying: Understanding the basics, ASM International (2001) 351. DOI:10.1361/autb2001p35110.1361/autb2001p351Search in Google Scholar

[3] S. Suresha, B.K. Sridhara: Mater. Des. 31 (2010) 1804. DOI:10.1016/j.matdes.2009.11.01510.1016/j.matdes.2009.11.015Search in Google Scholar

[4] N. Panwar, A. Chauhan: Mater. Today Proc. 5 (2018) 5933. DOI:10.1016/j.matpr.2017.12.19410.1016/j.matpr.2017.12.194Search in Google Scholar

[5] N. Radhika, R. Subramanian, V. Prasat, B. Anandavel: Ind. Lub. Trib. 64 (2012) 359. DOI:10.1108/0036879121126249910.1108/00368791211262499Search in Google Scholar

[6] V. Rastogi, R. Sharma: Ind. J. Pure & Applied Phys. 56 (2018) 164. URL: http://nopr.niscair.res.in/handle/123456789/43556Search in Google Scholar

[7] B. Duan, Y. Zhou, D. Wang, Y. Zhao: J. Alloys Compd. 771 (2019) 498. DOI:10.1016/j.jallcom.2018.08.31510.1016/j.jallcom.2018.08.315Search in Google Scholar

[8] H. Singh, H. Bhowmick: Trib. Int. 127 (2018) 509. DOI:10.1016/j.triboint.2018.06.03010.1016/j.triboint.2018.06.030Search in Google Scholar

[9] H. Kurita, H. Kwon, M. Estili, A. Kawasaki: Mat. Trans. 52 (2011) 1960. DOI:10.2320/matertrans.m201114610.2320/matertrans.m2011146Search in Google Scholar

[10] W.W. Wai, L. Eugene, M. Gupta: J. Microwave Power and Electromagnetic Energy 44 (2010) 14. PMid:21721326; DOI:10.1080/08327823.2010.1168977310.1080/08327823.2010.11689773Search in Google Scholar PubMed

[11] M.P. Reddy, F. Ubaid, R.A. Shakoor, A.M.A. Mohamed, W. Madhuri: J. Sci. Adv. Mater. Devices 1 (2016) 362. DOI:10.1016/j.jsamd.2016.07.00510.1016/j.jsamd.2016.07.005Search in Google Scholar

[12] P. Matli, R. Shakoor, A. Amer Mohamed, M. Gupta: Metals (Basel) 6 (2016) 143. DOI:10.3390/met607014310.3390/met6070143Search in Google Scholar

[13] C. Honnaiah, M.S. Srinath, S.L. Ajit Prasad: InAIP Conference Proceedings 1943 (2018) 020060. DOI:10.1063/1.502963610.1063/1.5029636Search in Google Scholar

[14] D. Gupta, A.K. Sharma: Surf. Coat. Technol. 205 (2011) 5147. DOI:10.1016/j.surfcoat.2011.05.01810.1016/j.surfcoat.2011.05.018Search in Google Scholar

[15] S. Singh, D. Gupta, V. Jain: Proc. IMechE, Part B: J. Eng. Manuf. 232 (2016) 1235. DOI:10.1177/095440541666690010.1177/0954405416666900Search in Google Scholar

[16] S. Kaushal, D. Gupta, H. Bhowmick: J. Tribol. 139 (2017) 061602. DOI:10.1115/1.403584410.1115/1.4035844Search in Google Scholar

[17] M. Oghbaei, O. Mirzaee: J. Alloys Compd. 494 (2010) 175. DOI:10.1016/j.jallcom.2010.01.06810.1016/j.jallcom.2010.01.068Search in Google Scholar

[18] B.J. Rael, Y. Fu, T.A. Khraishi, Y. Jiang: J. Comp. Mat. 50 (2015) 2375. DOI:10.1177/002199831560379010.1177/0021998315603790Search in Google Scholar

Received: 2019-06-20
Accepted: 2019-11-10
Published Online: 2021-03-22

© 2021 Walter de Gruyter GmbH, Berlin/Boston, Germany

Articles in the same Issue

  1. Contents
  2. Original Contributions
  3. Distributions of As, Pb, Sn and Zn as minor elements between iron silicate slag and copper in equilibrium with tridymite in the Cu–Fe–O–Si system
  4. Short Communications
  5. Free vibration analysis and selection of composite for high strength and stiffness using multi-attribute decision making
  6. Metallurgical and wear study of MWCNT-reinforced h-AMMC fabricated through microwave hybrid sintering
  7. Effects of microstructure and lattice misfit on creep life of Ni-based single crystal superalloy during long-term thermal exposure
  8. Fracture toughness assessment at different regions in an inertial friction welded Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy plate
  9. Microstructure and mechanical property improvement of dissimilar metal joints for TC4 Ti alloy to Nitinol NiTi alloy by laser welding
  10. The influence of gadolinium on Al–Ti–C master alloy and its refining effect on AZ31 magnesium alloy
  11. Effect of adding rare-earth cerium on the microstructure and acid rain corrosion resistance of the ADC12 alloy
  12. Effect of TiO2 crystal form on the denitration performance of Ce–W–Ti catalyst
  13. Notifications
  14. Deutsche Gesellschaft für Materialkunde / German Materials Science Society
https://doi.org/10.3139/146.111884
Keywords for this article
Hybrid aluminium metal matrix composite; Microwave; Sintering; Carbon nanotube; Wear

Articles in the same Issue

  1. Contents
  2. Original Contributions
  3. Distributions of As, Pb, Sn and Zn as minor elements between iron silicate slag and copper in equilibrium with tridymite in the Cu–Fe–O–Si system
  4. Short Communications
  5. Free vibration analysis and selection of composite for high strength and stiffness using multi-attribute decision making
  6. Metallurgical and wear study of MWCNT-reinforced h-AMMC fabricated through microwave hybrid sintering
  7. Effects of microstructure and lattice misfit on creep life of Ni-based single crystal superalloy during long-term thermal exposure
  8. Fracture toughness assessment at different regions in an inertial friction welded Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy plate
  9. Microstructure and mechanical property improvement of dissimilar metal joints for TC4 Ti alloy to Nitinol NiTi alloy by laser welding
  10. The influence of gadolinium on Al–Ti–C master alloy and its refining effect on AZ31 magnesium alloy
  11. Effect of adding rare-earth cerium on the microstructure and acid rain corrosion resistance of the ADC12 alloy
  12. Effect of TiO2 crystal form on the denitration performance of Ce–W–Ti catalyst
  13. Notifications
  14. Deutsche Gesellschaft für Materialkunde / German Materials Science Society
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 31.12.2025 from https://www.degruyterbrill.com/document/doi/10.3139/146.111884/html
Scroll to top button