Startseite Tribological performance of glass/epoxy composites filled with MWCNTs
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Tribological performance of glass/epoxy composites filled with MWCNTs

  • İsmail Ovali
Veröffentlicht/Copyright: 26. März 2018
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 109 Heft 4

Abstract

The effect of addition of multi-walled carbon nanotubes (MWCNTs) on the wear behaviour of glass/epoxy composites manufactured using the pre-preg method was investigated. The MWCNT filling rates were 0.5, 1, and 2 wt.%, and unfilled composite samples were used for comparison. The worn surfaces were characterised by means of scanning electron microscopy for evaluating the wear mechanisms. The experimental results showed that all the composites filled with MWCNTs have a lower wear loss than the unfilled composite sample, and the wear resistance increased with increase in the amount of MWCNTs. It is revealed that the abrasive wear resistance of the glass/epoxy composites is mainly related to the adhesion at the matrix and fibre interface.

Keywords: Carbon nanotubes; Glass/epoxy composite; Wear resistance; Interfacial adhesion
*Correspondence address, İsmail Ovali, Faculty of Manufacturing Engineering, Pamukkale University, Kınıklı. P.C 20160-1996 Denizli, Turkey, Fax: +90-2582934138, E-mail:

References

[1] B.Suresha, G.Chandramohan, N.M.Renukappa: J. Appl. Polym. Sci.103 (2006) 2472. 10.1002/app.25413Suche in Google Scholar

[2] W.Hufenbach, A.Stelmakh, K.Kunze, R.Böhm, R.Kupfer: Tribol. Int.49 (2011) 8. 10.1016/j.triboint.2011.12.010Suche in Google Scholar

[3] M.Kim, Y.B.Park, O.I.Okoli, C.Zhang: Compos. Sci. Technol.69 (2008) 42. 10.1016/j.compscitech.2008.10.019Suche in Google Scholar

[4] L.Torre, J.M.Kenny, A.M.Maffezzoli: Mater. Sci.33 (1998) 43. 10.1023/A:1004399923891Suche in Google Scholar

[5] A.R.Bahramian, M.Kokab: Hazard. Mater.166 (2008) 54. 10.1016/j.jhazmat.2008.11.061Suche in Google Scholar PubMed

[6] S.Sing, P.K.Guchhait, G.G.Bandyopadhyay, T.K.Chaki: Compos. Part A8 (2008) 44. 10.1016/j.jhazmat.2008.11.061Suche in Google Scholar

[7] K.T.Hsiao, J.Alms, S.G.Advani: Nan.Tech.14 (2003) 3. 10.1088/0957-4484/14/7/316Suche in Google Scholar

[8] Y.Zhou, F.Pervin, V.K.Rangari, S.Jeelani: Mater. Sci. Eng.A426 (2006) 8. 10.1016/j.msea.2006.04.031Suche in Google Scholar

[9] M.H.G.Wichmann, J.Sumfleth, F.H.Gojny, M.Quaresimin, B.Fiedler, K.Schulte: Eng. Fract. Mech.73 (2006) 59. 10.1016/j.engfracmech.2006.05.015Suche in Google Scholar

[10] T.Yokozeki, Y.Iwahori, S.Ishiwata: Compos. Part A38 (2006) 24. 10.1016/j.compositesa.2006.07.005Suche in Google Scholar

[11] N.A.Siddiqui, R.S.C.Woo, J.K.Kim, C.C.K.Leung, A.Munir: Compos. Part A38 (2006) 60. 10.1016/j.compositesa.2006.03.001Suche in Google Scholar

[12] J.Zhu, A.Imam, R.Crane, K.Lozano, V.Khabashesku, E.V.Barrera: Comp. Sci. Tech.67 (2006) 17. 10.1016/j.compscitech.2006.07.018Suche in Google Scholar

[13] H.Qian, E.S.Greenhalgh, M.S.P.Shaffer, A.Bismarck: J. Mater. Chem.20 (23) (2010) 4751. 10.1039/c000041 hSuche in Google Scholar

[14] E.T.Thostenson, W.Z.Li, D.Z.Wang, Z.F.Ren, T.W.Chou: J. Appl. Phys.91 (9) (2002) 6034. 10.1063/1.1466880Suche in Google Scholar

[15] X.He, F.Zhang, R.Wang, W.Liu: Car.45 (13) (2007) 2559. 10.1016/j.carbon.2007.08.018Suche in Google Scholar

[16] T.Kashiwagi, F.Du, K.I.Winey, K.M.Groth, J.R.Shields, S.P.Bellayer: Poly.46 (2004) 81. 10.1016/j.polymer.2004.10.087Suche in Google Scholar

[17] B.H.Cipiriano, T.Kashiwagi, S.R.Raghavan, Y.Yang, E.A.Grulke, K.Yamamoto: Poly.48 (2007) 96. 10.1016/j.polymer.2007.07.070Suche in Google Scholar

[18] R.B.Mathur, S.Chatterjee, B.P.Singh: Comp. Sci. Tech.68 (2008) 15. 10.1016/j.compscitech.2008.02.020Suche in Google Scholar

[19] J.P.Salvetat, A.Rubio: Car.40 (2002): 34. 10.1016/S0008-6223(02)00012-XSuche in Google Scholar

[20] E.Zahra, Y.Farshad, M.A.Mirzapour: Compos. Part A72 (2015) 22. 10.1016/j.compositesa.2015.01.015Suche in Google Scholar

[21] L.C.Zhang, I.Zarudi, K.Q.Xiao: Wear.261 (2006) 11. 10.1016/j.wear.2006.01.033Suche in Google Scholar

[22] B.Dong, Z.Yang, Y.Huang, H.-L., Li: Tribol. Lett.20 (2005) 4. 10.1007/s11249-005-8637-8Suche in Google Scholar

[23] O.Jacobs, W.Xu, B.Schädel, W.Wu: Tribol. Lett.23 (2006) 75. 10.1007/s11249-006-9042-7Suche in Google Scholar

[24] H.Chen, O.Jacobs, W.Wu, G.Rüdiger, B.Schädel: Polym. Tes.26 (2006) 60. 10.1016/j.polymertesting.2006.11.004Suche in Google Scholar

[25] H.Wang, J.Feng, X.Hu, K.M.Ng: Polym. Eng. Sci.48 (2008) 75. 10.1002/pen.20979Suche in Google Scholar

[26] X.J.Shen, X.Q.Pei, Y.Liu, S.Y.Fu: Com. B. Eng.57 (2014) 5. 10.1016/j.compositesb.2013.09.050Suche in Google Scholar

[27] H.Wang, L.Chang, X.Yang, L.Yuan, L.Ye, Y.Zhu: Car.67 (2013) 47. 10.1016/j.carbon.2013.09.052.Suche in Google Scholar

[28] H.Wang, L.Sun, R.Wang, L.Yan, Y.Zhu, C.Wang: Poly. Comp. (2015) 12.10.1155/2015/680853Suche in Google Scholar PubMed PubMed Central

[29] R.Baptista, A.Mend, F.Rodrigues, C.Figueiredo-Pina, M.Guedes, R.Marat-Mendes: Theo. and App. Frac. Mech.,85 (2016) 113. 10.1016/j.tafmec.2016.08.013Suche in Google Scholar

[30] R.Bobbili, V.Madhu, A.K.Gogia: Eng. Sci. Tech., Int. J.19 (2015) 8. 10.1016/j.jestch.2015.07.008Suche in Google Scholar

[31] C.Guignier, M.A.Bueno, B.Camillieri, M.Tourlonias, B.Durand: Comp. P. A: App. Sci. and Man.71 (2015) 168. 10.1016/j.compositesa.2015.01.013Suche in Google Scholar

[32] K.S.Prakash, T.R.Thankachan: Tran. Non. Met. Soc. Ch.27 (2017) 627. 10.1016/S1003-6326(17)60070-0Suche in Google Scholar

[33] A.Papadopoulos, G.Gkikas, A.S.Paipetis, N.M.Barkoula: Compos. Part A84 (2016) 299. 10.1016/j.compositesa.2016.02.012Suche in Google Scholar

[34] ASTM standard test method for wear testing with a Pin-on-Disc apparatus. ASTM G 99-95. Philadelphia, PA: 1995. 10.1520/G0099-95AR00E01Suche in Google Scholar

Received: 2017-06-03
Accepted: 2017-11-21
Published Online: 2018-03-26
Published in Print: 2018-04-13

© 2018, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Deposition of CVD-TiCN and TiAlN coatings guided with thermodynamic calculations
  5. Microstructure and mechanical properties of ultra-fine WC-10Co cemented carbides with Cr3C2 and NbC: Experimental investigation supported by thermodynamic calculation
  6. Enthalpies of mixing in binary Mn–In and ternary Mn–In–Gd liquid alloys
  7. Thermal stability of Nb–Cr–Mo alloy
  8. Effect of processing parameters on the grain refinement of vanadium nitrogen microalloyed steel
  9. Effects of heat treatment and testing temperature on the tensile properties of Al–Cu and Al–Cu–Si based alloys
  10. Fabrication of Al–Si Gasar by mold casting technique
  11. Tribological performance of glass/epoxy composites filled with MWCNTs
  12. Reaction fabrication and wear performance of TiCx/(Cu–A1) bonded diamond composites
  13. DC-EPD of nanoceramic particles accelerated via anodic dissolution in organic media
  14. Short Communications
  15. Formation of zirconia precursor nanoplates mediated by ionic liquid and transformation to monoclinic ZrO2 nanostructures
  16. Characterization of interfaces in tri-layered brass/steel/brass composites fabricated by casting and hot dipping
  17. DGM News
  18. DGM News
https://doi.org/10.3139/146.111607
Schlagwörter für diesen Artikel
Carbon nanotubes; Glass/epoxy composite; Wear resistance; Interfacial adhesion

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Deposition of CVD-TiCN and TiAlN coatings guided with thermodynamic calculations
  5. Microstructure and mechanical properties of ultra-fine WC-10Co cemented carbides with Cr3C2 and NbC: Experimental investigation supported by thermodynamic calculation
  6. Enthalpies of mixing in binary Mn–In and ternary Mn–In–Gd liquid alloys
  7. Thermal stability of Nb–Cr–Mo alloy
  8. Effect of processing parameters on the grain refinement of vanadium nitrogen microalloyed steel
  9. Effects of heat treatment and testing temperature on the tensile properties of Al–Cu and Al–Cu–Si based alloys
  10. Fabrication of Al–Si Gasar by mold casting technique
  11. Tribological performance of glass/epoxy composites filled with MWCNTs
  12. Reaction fabrication and wear performance of TiCx/(Cu–A1) bonded diamond composites
  13. DC-EPD of nanoceramic particles accelerated via anodic dissolution in organic media
  14. Short Communications
  15. Formation of zirconia precursor nanoplates mediated by ionic liquid and transformation to monoclinic ZrO2 nanostructures
  16. Characterization of interfaces in tri-layered brass/steel/brass composites fabricated by casting and hot dipping
  17. DGM News
  18. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 6.10.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.111607/html
Button zum nach oben scrollen