Home Technology Characterization of interfaces in tri-layered brass/steel/brass composites fabricated by casting and hot dipping
Article
Licensed
Unlicensed Requires Authentication

Characterization of interfaces in tri-layered brass/steel/brass composites fabricated by casting and hot dipping

  • Amir Mahdi Rahimi and Ahmad Ali Amadeh
Published/Copyright: March 26, 2018
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 109 Issue 4

Abstract

Tri-layered brass steel/brass laminated composites were fabricated through hot dipping as well as casting. The chosen temperatures for hot dipping were 1 150 °C and 1 350 °C and for casting was 1 150 °C in addition to performing a heat treatment cycle at 900 °C for 90 min. The characterization results revealed that in the as-cast and the heat-treated samples, the formation of Fe-Zn intermetallic compounds occurred. In addition, with increasing the hot dipping temperature, stronger interfaces were achieved due to easier diffusion at higher temperatures. Moreover, casting without heat treatment was enough to obtain good bonding since the amount of Fe3Zn10 intermetallic compound increased and grain growth occurred.

Keywords: Laminated composite; Interface; Diffusion; Casting
*Correspondence address, Amir Mahdi Rahimi, Department of Materials Science and Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran, Tel.: +98 2144865179, Fax: +98 2144865154, E-mail:

References

[1] Y.Fouad: T. Indian I. Metals67 (2014) 979. 10.1007/s12666-014-0419-2Search in Google Scholar

[2] M.Slámová, P.Sláma, P.Homola, J.Uhlíř, M.Cieslar: Int. J. Mater. Res.100 (2009) 858. 10.3139/146.110106Search in Google Scholar

[3] M.Naseri, M.Reihanian, E.Borhani: J. Manuf. Process.24 (2016) 125. 10.1016/j.jmapro.2016.08.008Search in Google Scholar

[4] A.Shabani, M.R.Toroghinejad, A.Shafyei: Mater. Sci. Eng. A558 (2012) 386. 10.1016/j.msea.2012.08.017Search in Google Scholar

[5] A.Shabani, M.R.Toroghinejad, A.Shafyei: Mater. Des.40 (2012) 212. 10.1016/j.matdes.2012.03.052Search in Google Scholar

[6] D.M.Fronczek, R.Chulist, Z.Szulc, J.Wojewoda-Budka: Mater. Let.198 (2017) 160. 10.1016/j.matlet.2017.04.025Search in Google Scholar

[7] D.V.Lazurenko, I.A.Bataev, V.I.Mali, A.A.Bataev, I.N.Maliutina, V.S.Lozhkin, M.A.Esikov, A.M.J.Jorge: Mater. Des.102 (2016) 122. 10.1016/j.matdes.2016.04.037Search in Google Scholar

[8] S.Peng, S.Xie, Y.Yang, G.Xiao, J.Lu, L.Zhang: J. Alloys Compd.694 (2017) 1004. 10.1016/j.jallcom.2016.10.136Search in Google Scholar

[9] S.Peng, S.Xie, J.Lu, L.Zhang: J. Alloys Compd. (2017). 10.1016/j.jallcom.2017.09.091Search in Google Scholar

[10] W.Hu, W., Dan, W.Peng, G.Wu, Q.Du, J.Zhang: TMS 2016 proceedings (2016) 771. 10.1007/978-3-319-48254-5_92Search in Google Scholar

[11] G.Zhao, J.Zhao: Rare Metals31 (2016) 362. 10.1007/s12598-012-0521-8Search in Google Scholar

Received: 2017-09-21
Accepted: 2017-12-05
Published Online: 2018-03-26
Published in Print: 2018-04-13

© 2018, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Deposition of CVD-TiCN and TiAlN coatings guided with thermodynamic calculations
  5. Microstructure and mechanical properties of ultra-fine WC-10Co cemented carbides with Cr3C2 and NbC: Experimental investigation supported by thermodynamic calculation
  6. Enthalpies of mixing in binary Mn–In and ternary Mn–In–Gd liquid alloys
  7. Thermal stability of Nb–Cr–Mo alloy
  8. Effect of processing parameters on the grain refinement of vanadium nitrogen microalloyed steel
  9. Effects of heat treatment and testing temperature on the tensile properties of Al–Cu and Al–Cu–Si based alloys
  10. Fabrication of Al–Si Gasar by mold casting technique
  11. Tribological performance of glass/epoxy composites filled with MWCNTs
  12. Reaction fabrication and wear performance of TiCx/(Cu–A1) bonded diamond composites
  13. DC-EPD of nanoceramic particles accelerated via anodic dissolution in organic media
  14. Short Communications
  15. Formation of zirconia precursor nanoplates mediated by ionic liquid and transformation to monoclinic ZrO2 nanostructures
  16. Characterization of interfaces in tri-layered brass/steel/brass composites fabricated by casting and hot dipping
  17. DGM News
  18. DGM News
https://doi.org/10.3139/146.111614
Keywords for this article
Laminated composite; Interface; Diffusion; Casting

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Deposition of CVD-TiCN and TiAlN coatings guided with thermodynamic calculations
  5. Microstructure and mechanical properties of ultra-fine WC-10Co cemented carbides with Cr3C2 and NbC: Experimental investigation supported by thermodynamic calculation
  6. Enthalpies of mixing in binary Mn–In and ternary Mn–In–Gd liquid alloys
  7. Thermal stability of Nb–Cr–Mo alloy
  8. Effect of processing parameters on the grain refinement of vanadium nitrogen microalloyed steel
  9. Effects of heat treatment and testing temperature on the tensile properties of Al–Cu and Al–Cu–Si based alloys
  10. Fabrication of Al–Si Gasar by mold casting technique
  11. Tribological performance of glass/epoxy composites filled with MWCNTs
  12. Reaction fabrication and wear performance of TiCx/(Cu–A1) bonded diamond composites
  13. DC-EPD of nanoceramic particles accelerated via anodic dissolution in organic media
  14. Short Communications
  15. Formation of zirconia precursor nanoplates mediated by ionic liquid and transformation to monoclinic ZrO2 nanostructures
  16. Characterization of interfaces in tri-layered brass/steel/brass composites fabricated by casting and hot dipping
  17. DGM News
  18. DGM News
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2026 De Gruyter Brill
Downloaded on 1.2.2026 from https://www.degruyterbrill.com/document/doi/10.3139/146.111614/html
Scroll to top button