Home A discrete dislocation technique for fatigue microcracks (Part II)
Article
Licensed
Unlicensed Requires Authentication

A discrete dislocation technique for fatigue microcracks (Part II)

  • Vinko Močilnik and Nenad Gubeljak
Published/Copyright: May 16, 2018
Become an author with De Gruyter Brill

Abstract

The discrete nature of the phenomenon of crack initiation in the crystal grain lattice was investigated. Fatigue crack propagation within the crystalline grains, the influence of the vicinity of the grain boundary on its propagation and its arrest, and the dislocation modeling of short fatigue crack growth through single shear, were analyzed, respectively.

Kurzfassung

Die diskrete Natur der Rissbildung im Kristallgitter wurde untersucht. Die Ermüdungsrissausbreitung innerhalb der kristallinen Körner, der Einfluss der Korngrenzenumgebung auf Rissfortschritt und –stillstand und die Modellierung von Versetzungen für kurzes Ermüdungsrisswachstum durch Einfachscherung wurde analysiert.


*Correspondence Address, Prof. Dr. Nenad Gubeljak, University of Maribor, Faculty of Mechanical Engineering, Smetanova ul. 17, 2000 Maribor, Slovenia,

Dr. Vinko Močilnik was born in 1962. He graduated in 1986 from the Faculty of Mechanical Engineering, University of Ljubljana, Slovenia. He continued his postgraduate studies and received his PhD in 2009 at Faculty of Mechanical Engineering, University of Maribor, Slovenia. He worked for 18 years as a development engineer in the field of development and production of technological equipment for metallurgical industry. His main research areas are fatigue and fracture testing as well as application of these findings in manufacturing technologies and the development of new products. He is a researcher at the Institute of Mechanics, Faculty of Mechanical Engineering, University of Maribor and a lecturer at the Engineering High School.

Prof. Dr. Nenad Gubeljak was born in 1963. He graduated 1988 from University of Maribor, Slovenia, Faculty of Mechanical Engineering as BSc. He continued study at same faculty and completed as PhD in 1998. He spent a year as a guest researcher at GKKS Research Centre Geesthacht in Germany in 2000–2001. He is employed as Head of Institute of Mechanics and Chair of Mechanics at Faculty of Mechanical Engineering at University of Maribor. His main research areas are fatigue and fracture testing, analysis of fracture behavior of welded joints and structure integrity assessment.


References

1 V.Močilnik: The influence of pre-stress on dynamic capacity of the torsion springs, Doctoral thesis, University in Maribor, Slovenia, Faculty of Mechanical Engineering (2009)Search in Google Scholar

2 I. H.Lin, R.Thomson: Cleavage, dislocation emission, and shielding for cracks under general loading, Acta Metall. Mater. Vol. 34 (1986), pp. 18720610.1016/0001-6160(86)90191-4Search in Google Scholar

3 R.Pippan: Dislocation emission and fatigue crack growth threshold, Acta Metall. Mater. Vol. 39 (1991), pp. 25526210.1016/0956-7151(91)90304-JSearch in Google Scholar

4 F. O.Riemelmoser, R.Pippan, O.Kolednik: Cyclic crack growth in elastic plastic solids; A description in terms of dislocation theory, Comp. Mech. Vol. 20 (1997), pp. 13914410.1007/s004660050230Search in Google Scholar

5 F. O.Riemelmoser, R.Pippan, H. P.Stüwe: A comparison of a discrete dislocation model and a continuous description of cyclic crack tip plasticity, Int. J. of Fracture Vol. 85 (1997), pp. 15716810.1023/A:1007386208842Search in Google Scholar

6 C.Bjerkén, S.Melin: A tool to model short crack fatigue growth using a discrete dislocation formulation, Int. J. of Fatigue Vol. 6 (2003), No. 25, pp. 559566Search in Google Scholar

7 S.Pearson: Initiation of fatigue crack in commercial aluminium alloys and the subsequent propagation of very short cracks, Eng. Fract. Mech. Vol. 7 (1975), pp. 23524710.1016/0013-7944(75)90004-1Search in Google Scholar

8 F. O.Riemelmoser, R.Pippan, H. P.Stüwe: An argumentation for a cyclic by cyclic propagation of fatigue cracks at small stress intensity ranges, Acta Mater. Vol. 46 (1998), No. 5, pp. 1793179910.1016/S1359-6454(97)00366-2Search in Google Scholar

9 F. O.Riemelmoser, R.Pippan: Intrinsic material behavior in the near threshold regime, In X. R.Wu in Z. G.Wang, editors, Fatigue ‘99, Proc. 7th Int. Fatigue Congress, Vol. 1/4, Beijing, P.R. China, Higher Education Press (1999), pp. 387392Search in Google Scholar

10 P.Hansson, S.Melin, C.Persson: Dislocation modelling of short fatigue crack growth through shingle shear, Licentiate Dissertation, Department of Mechanical Engineering, Lund University, Sweden (2004)Search in Google Scholar

11 C.Bjerken, S.Melin: A study of the influence of grain boundaries on short crack growth during varying load using a dislocation technique, Eng. Fract. Mech. Vol. 15 (2004), No. 71, pp. 22152227Search in Google Scholar

12 C.Bjerken: The discrete nature of the growth and arrest of micro structurally short fatigue cracks modeled by a dislocation technique, Paper E, Department of Mechanical Engineering, Lund University, P. O. Box 118, S-221 00 Lund, SwedenSearch in Google Scholar

Published Online: 2018-05-16
Published in Print: 2015-01-05

© 2015, Carl Hanser Verlag, München

Articles in the same Issue

  1. Inhalt/Contents
  2. Inhalt
  3. Fachbeiträge/Technical Contributions
  4. A simple procedure for estimating SN-lines for crack initiation from SN-lines for total failure*
  5. Modellbasierte Korrelation zwischen dem elektrischen Widerstand und der Versetzungsstruktur des ermüdungsbeanspruchten ICE-Radstahls R7
  6. Effect of cobalt on the aging kinetics and the properties of a CuCoNiBe alloy
  7. Effect of heat treatment on microstructure and mechanical properties of Fe-5Cr-1.4B alloy
  8. Interface characterization of friction welded low carbon steel and copper alloys
  9. Field test methods for aluminum gas cylinders
  10. Application of the Taguchi method for parameter optimization of the surface grinding process
  11. A discrete dislocation technique for fatigue microcracks (Part I)
  12. A discrete dislocation technique for fatigue microcracks (Part II)
  13. Synchrotron X-ray CT of rose peduncles – evaluation of tissue damage by radiation*
  14. Surface roughness analysis and optimization for the CNC milling process by the desirability function combined with the response surface methodology
  15. Design, manufacture and analysis of composite epoxy material with embedded silicon carbide (SiC) and alumina (Al2O3) nanoparticles/fibers
  16. Performance of organic and inorganic substances as inhibitors for chloride-induced corrosion in concrete
  17. Fillet welding of austenitic stainless steel using the double channel shielding gas method with cored wire
  18. Applying quadraphonic transmission ultrasonic defectoscopy on standard aluminum materials
  19. Kalender/Calendar
  20. Kalender
Downloaded on 26.10.2025 from https://www.degruyterbrill.com/document/doi/10.3139/120.110678/html
Scroll to top button