Ultrasonic Vibration Hot Embossing
-
S.-J. Liu
Abstract
Hot embossing has become a popular method for replicating precise micro-features onto large plastic plates. However, a long cycle time of the process due to conventional electric heating or hot oil heating is one of problems that confound the overall success of this technology. This study proposed a novel hot embossing method by using ultrasonic vibration as a heat generator. Experiments were carried out on a 2000-watt ultrasonic welding machine. A 2 mm thick polymethyl methyl acrylic (PMMA) plate was used for embossing microstructures onto its surface. The results in this study suggest that ultrasonic vibration hot embossing can provide an effective way of molding microstructures onto the surface of polymeric plates. Nevertheless, this novel process will need some improvements in the design of the ultrasonic vibration machine in order to make the process feasible.
Acknowledgements
The authors thank Prof. S. Y. Yang and Dr. C. Y. Chang of National Taiwan University, for the preparation of the master mold for this experimental study.
References
1 Jaszewski, R. W., Schift, H., Gobercht, J., Smith, P.: Microelectronic Engineering 41/42, p. 575 (1998)10.1016/S0167-9317(98)00135-XSuche in Google Scholar
2 Heckele, M., Bacher, W., Mueller, K. D.: Microsystem Technologies 4, p. 122 (1998)10.1007/s005420050112Suche in Google Scholar
3 Niggermann, M., Ehrfeld, W., Weber, L., Gunther, R., Sollbohmer, O.: Microsystem Technologies 6, p. 48 (1999)10.1007/s005420050174Suche in Google Scholar
4 Lin, L., Cheng, Y. T., Chiu, C. J.: Microsystem Technologies 4, p. 113 (1998)10.1007/s005420050109Suche in Google Scholar
5 Romankiw, L. T.: Eletrcochimica Acta 42, p. 2985 (1997)10.1016/S0013-4686(97)00146-1Suche in Google Scholar
6 Liu, S.-J., Chang, B. C., Chien, L. H., Tsai, Y. H.: Plastics Rubber and Composites 27, p. 279 (1998)Suche in Google Scholar
7 Liu, S.-J., Lin, W. F., Chang, B. C., Wu, G., Hung, S. W.: Advances in Polymer Technology 18, p. 125 (1999)10.1002/(SICI)1098-2329(199922)18:2<125::AID-ADV3>3.0.CO;2-ASuche in Google Scholar
8 Liu, S.-J., Chang, I. T.: Polymer Composites 22, p. 132 (2001)10.1002/pc.10525Suche in Google Scholar
© 2005 Hanser Publishers, Munich
Artikel in diesem Heft
- Contents
- Regular Contributed Articles
- An Improvement on Design of Sheet Extrusion Dies
- Organic-Inorganic Hybrid Material Synthesis by on Line Coupling Twin Screw Extruder with a Microwave Oven
- Water Penetration Stability in Water Assisted Injection Molded Symmetric Ribs
- A New Plasticating Model for Amorphous and Semi-crystalline Polymers in Single Screw Extruders
- Simultaneous Biaxial Stretching of Polypropylene Resins of Varying Tacticity
- Optimization of a Flat Die Including Elongational Viscosity Effects
- Experimental Study on Factors Influencing Throughput Rate and Process of Polymer-Mineral Filler Mixing in a Twin Screw Extruder
- 3D Finite Element Simulation of Processing of Generalized Newtonian Fluids in Counter-rotating and Tangential TSE and Die Combination
- Simulation of Heat Transfer in Laser Transmission Welding
- Influence of Power Law and Isothermal Simplification on the Accuracy in Single Screw Extrusion
- Melt Intercalation in Montmorillonite/Polystyrene Nanocomposites
- Experimental Investigation of the Effect of the Bubble Cone on the Cooling Jets used in the Blown Film Manufacturing Process
- Molding of Thin Sheets Using Impact Micro-injection Molding
- Rapid communications
- Ultrasonic Vibration Hot Embossing
- PPS news
- PPS news
- Seikei-kakou abstracts
- Seikei-kakou abstracts
Artikel in diesem Heft
- Contents
- Regular Contributed Articles
- An Improvement on Design of Sheet Extrusion Dies
- Organic-Inorganic Hybrid Material Synthesis by on Line Coupling Twin Screw Extruder with a Microwave Oven
- Water Penetration Stability in Water Assisted Injection Molded Symmetric Ribs
- A New Plasticating Model for Amorphous and Semi-crystalline Polymers in Single Screw Extruders
- Simultaneous Biaxial Stretching of Polypropylene Resins of Varying Tacticity
- Optimization of a Flat Die Including Elongational Viscosity Effects
- Experimental Study on Factors Influencing Throughput Rate and Process of Polymer-Mineral Filler Mixing in a Twin Screw Extruder
- 3D Finite Element Simulation of Processing of Generalized Newtonian Fluids in Counter-rotating and Tangential TSE and Die Combination
- Simulation of Heat Transfer in Laser Transmission Welding
- Influence of Power Law and Isothermal Simplification on the Accuracy in Single Screw Extrusion
- Melt Intercalation in Montmorillonite/Polystyrene Nanocomposites
- Experimental Investigation of the Effect of the Bubble Cone on the Cooling Jets used in the Blown Film Manufacturing Process
- Molding of Thin Sheets Using Impact Micro-injection Molding
- Rapid communications
- Ultrasonic Vibration Hot Embossing
- PPS news
- PPS news
- Seikei-kakou abstracts
- Seikei-kakou abstracts
