Startseite A New Plasticating Model for Amorphous and Semi-crystalline Polymers in Single Screw Extruders
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

A New Plasticating Model for Amorphous and Semi-crystalline Polymers in Single Screw Extruders

  • G. Zitzenbacher und G. R. Langecker
Veröffentlicht/Copyright: 3. März 2022
Veröffentlichen auch Sie bei De Gruyter Brill
Manuskript einreichen Informationen für Autor*innen
International Polymer Processing
Aus der Zeitschrift International Polymer Processing Band 20 Heft 4

Abstract

Polymeric thermoplastic materials can be subdivided in amorphous and semi-crystalline ones. In contrast to semi-crystalline polymers amorphous thermoplastic materials have no defined phase transition and hence no melt enthalpy. The glass transition region describes the change of the material behaviour from the state of a rubber like to an under-cooled fluid (glassy state). Setting the melt enthalpy in the Stefan-Neumann problem zero gives no valid results for the solid bed profile. Thus this condition is unsuitable for describing the plasticating process of amorphous polymers.

In this paper a new model for the plastication of amorphous and semi-crystalline polymers in single screw extruders is presented. Therefore a new calculation method for the determination of the moving velocity between the glassy solid bed and the softened film region on the barrel surface is developed. The whole enthalpy to heat up the polymer on a critical flow temperature in the screw channel is considered.

* Mail address: G. Zitzenbacher, University of Applied Sciences FH-Wels, Department of Material Engineering, Roseggerstrasse 12, A-4600 Wels, Austria

  1. YYou will find the article and additional material by entering the document number IIPP0089 on our website at www.polymer-process.com

References

1 Maddock, B. H.: SPE-ANTEC Tech. Papers 15, p. 383 (1959)10.1002/phbl.19590150813Suche in Google Scholar

2 Tadmor, Z.: Poly. Eng. Sci. 6, p 185 (1966)10.1002/pen.760060303Suche in Google Scholar

3 Tadmor, Z., Duvdevani, I. J., Klein, I.: Poly. Eng. Sci. 7, p. 198 (1967)10.1002/pen.760070313Suche in Google Scholar

4 Tadmor, Z., Klein, I.: Engineering Principles of Plasticating Extrusion. Van Nostrand Reinhold, New York (1970)Suche in Google Scholar

5 Donovan, R. C.: Poly. Eng. Sci. 11, p. 247 (1971)10.1002/pen.760110313Suche in Google Scholar

6 Kacir, L., Tadmor, Z.: Poly. Eng. Sci. 12, p. 387 (1972)10.1002/pen.760120511Suche in Google Scholar

7 Lindt, J. T.: Poly. Eng. Sci. 16, p. 284 (1976)10.1002/pen.760160411Suche in Google Scholar

8 Fenner, R. T.: Principles of Polymer Processing. MacMillan, London (1979)10.1007/978-1-349-16234-5Suche in Google Scholar

9 Cox, A. P. D., Fenner, R. T.: Poly. Eng. Sci. 20, p. 562 (1980)10.1002/pen.760200809Suche in Google Scholar

10 Mount, E. M., Watson, J. G., Chung, C. I.: Poly. Eng. Sci. 22, p. 729 (1982)10.1002/pen.760221202Suche in Google Scholar

11 Kuo, S. H., Chung, C. I.: Poly. Eng. Sci. 7, p. 448 (1989)10.1002/pen.760290704Suche in Google Scholar

12 Rauwendaal, C.: Poly. Eng. Sci. 22, p. 729 (1982)10.1002/pen.760221202Suche in Google Scholar

13 Fukase, H. et al.: Poly. Eng. Sci. 22, p. 578 (1982)10.1002/pen.760220910Suche in Google Scholar

14 Elbirli, B. et al.: Poly. Eng. Sci. 24, p. 988 (1984)10.1002/pen.760241208Suche in Google Scholar

15 Lindt, J. T., Elbirli, B.: Poly. Eng. Sci. 25, p. 412 (1985)10.1002/pen.760250706Suche in Google Scholar

16 Pearson, J. R. A.: Mechanics of Polymer Processing. Elsevier, London New York (1985)Suche in Google Scholar

17 Potente, H.: Verfahrenstechnische Auslegung von Plastifizier- und Schmelzeaggregaten. Handbook for “1. Kunststofftechnischen Seminar”. University Paderborn (1986)Suche in Google Scholar

18 Potente, H.: Int. Poly. Process. 6, p. 297 (1991)10.3139/217.910297Suche in Google Scholar

19 Schöppner, V.: Thesis, University Paderborn (1995)Suche in Google Scholar

20 Binder, W.: Thesis, University of Leoben (1999)Suche in Google Scholar

21 Han, C. D., Lee, K. Y., Wheeler, N. C.: Poly. Eng. Sci. 36, p. 1360 (1996)10.1002/pen.10531Suche in Google Scholar

22 Sundstrom, D. W., Lo, J. R.: Poly. Eng. Sci. 18, p. 422 (1978)10.1002/pen.760180515Suche in Google Scholar

23 Tadmor, Z., Gogos, C. G.: Principles of Polymer Processing. John Wiley & Sons, New York (1979)Suche in Google Scholar
Received: 2004-09-21
Accepted: 2005-07-17
Published Online: 2022-03-03

© 2005 Hanser Publishers, Munich

Artikel in diesem Heft

  1. Contents
  2. Regular Contributed Articles
  3. An Improvement on Design of Sheet Extrusion Dies
  4. Organic-Inorganic Hybrid Material Synthesis by on Line Coupling Twin Screw Extruder with a Microwave Oven
  5. Water Penetration Stability in Water Assisted Injection Molded Symmetric Ribs
  6. A New Plasticating Model for Amorphous and Semi-crystalline Polymers in Single Screw Extruders
  7. Simultaneous Biaxial Stretching of Polypropylene Resins of Varying Tacticity
  8. Optimization of a Flat Die Including Elongational Viscosity Effects
  9. Experimental Study on Factors Influencing Throughput Rate and Process of Polymer-Mineral Filler Mixing in a Twin Screw Extruder
  10. 3D Finite Element Simulation of Processing of Generalized Newtonian Fluids in Counter-rotating and Tangential TSE and Die Combination
  11. Simulation of Heat Transfer in Laser Transmission Welding
  12. Influence of Power Law and Isothermal Simplification on the Accuracy in Single Screw Extrusion
  13. Melt Intercalation in Montmorillonite/Polystyrene Nanocomposites
  14. Experimental Investigation of the Effect of the Bubble Cone on the Cooling Jets used in the Blown Film Manufacturing Process
  15. Molding of Thin Sheets Using Impact Micro-injection Molding
  16. Rapid communications
  17. Ultrasonic Vibration Hot Embossing
  18. PPS news
  19. PPS news
  20. Seikei-kakou abstracts
  21. Seikei-kakou abstracts
https://doi.org/10.1515/ipp-2005-0064

Artikel in diesem Heft

  1. Contents
  2. Regular Contributed Articles
  3. An Improvement on Design of Sheet Extrusion Dies
  4. Organic-Inorganic Hybrid Material Synthesis by on Line Coupling Twin Screw Extruder with a Microwave Oven
  5. Water Penetration Stability in Water Assisted Injection Molded Symmetric Ribs
  6. A New Plasticating Model for Amorphous and Semi-crystalline Polymers in Single Screw Extruders
  7. Simultaneous Biaxial Stretching of Polypropylene Resins of Varying Tacticity
  8. Optimization of a Flat Die Including Elongational Viscosity Effects
  9. Experimental Study on Factors Influencing Throughput Rate and Process of Polymer-Mineral Filler Mixing in a Twin Screw Extruder
  10. 3D Finite Element Simulation of Processing of Generalized Newtonian Fluids in Counter-rotating and Tangential TSE and Die Combination
  11. Simulation of Heat Transfer in Laser Transmission Welding
  12. Influence of Power Law and Isothermal Simplification on the Accuracy in Single Screw Extrusion
  13. Melt Intercalation in Montmorillonite/Polystyrene Nanocomposites
  14. Experimental Investigation of the Effect of the Bubble Cone on the Cooling Jets used in the Blown Film Manufacturing Process
  15. Molding of Thin Sheets Using Impact Micro-injection Molding
  16. Rapid communications
  17. Ultrasonic Vibration Hot Embossing
  18. PPS news
  19. PPS news
  20. Seikei-kakou abstracts
  21. Seikei-kakou abstracts
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 25.9.2025 von https://www.degruyterbrill.com/document/doi/10.1515/ipp-2005-0064/html
Button zum nach oben scrollen