Startseite Technik The effect of quench-aging on the mechanical properties of Zn-27Al-1Cu alloy
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

The effect of quench-aging on the mechanical properties of Zn-27Al-1Cu alloy

  • Murat Aydın und Fatih Şenaslan
Veröffentlicht/Copyright: 27. Juli 2018
Veröffentlichen auch Sie bei De Gruyter Brill
Manuskript einreichen Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 109 Heft 8

Abstract

The ternary alloy Zn-27Al-1Cu was produced by permanent mold casting. As-cast alloy was aged for different periods after being subjected to solution treatment followed by water quenching. The microstructure, mechanical properties and fatigue behavior of as-cast and heat-treated alloy were then investigated. The quench-aging eliminated the as-cast dendritic structure and produced a uniform microstructure consisting of large grains combined with precipitates. The hardness and tensile strength generally increased, whereas the ductility slightly decreased with aging time. Under all conditions, the longest fatigue life was obtained from the alloy that had been aged for 0.5 h, while the alloy which had been aged for 10 h exhibited the shortest. The fatigue properties were found to be more dependent on impact toughness and elongation, rather than tensile strength.

Keywords: Zn–Al alloys; Fatigue; Aging; Mechanical properties
*Correspondence address, Associate Professor Murat Aydın, Department of Mechanical Engineering, Karadeniz Technical University, Kanuni Campus, Trabzon 61080, Turkey, Tel.: +90462 3774131, Fax: +90462 3773336, E-mail: , Web: http://aves.ktu.edu.tr/maydin/

References

[1] B.K.Prasad: Metall. Mater. Trans. A28 (1997) 809. 10.1007/s11661-997-1008-3Suche in Google Scholar

[2] T.Savaskan, S.Murphy: Wear116 (1987) 211. 10.1016/0043-1648(87)90234-1Suche in Google Scholar

[3] E.Gervais, R.J.Barnhurst, C.A.Loong: JOM37 (1985) 43. 10.1007/BF03258743Suche in Google Scholar

[4] B.K.Prasad: Wear240 (2000) 100. 10.1016/S0043-1648(00)00369-0Suche in Google Scholar

[5] T.Savaşkan, A.P.Hekimoğlu, G.Pürçek: Tribol. Int.37 (2004) 45. 10.1016/S0301-679X(03)00113-0Suche in Google Scholar

[6] T.Calayag, D.Ferres: SAE Tech. Pap.820643 (1982) 2241. DIO: 10.4271/820643.Suche in Google Scholar

[7] M.Durman, S.Murphy: J. Mater. Sci.32 (1997) 1603. 10.1023/A:1018595110144Suche in Google Scholar

[8] T.Savaşkan, O.Bican: Mater. Sci. Eng. A404 (2005) 259. 10.1016/j.msea.2005.05.078Suche in Google Scholar

[9] P.P.Lee, T.Savaskan, E.Laufer: Wear117 (1987) 79. 10.1016/0043-1648(87)90245-6Suche in Google Scholar

[10] T.Savaşkan, G.Pürçek, A.P.Hekimoğlu: Tribol. Lett.15 (2003) 257. 10.1023/A:1024817304351Suche in Google Scholar

[11] T.Savaşkan, Z.Azaklı: Wear264 (2008) 920. 10.1016/j.wear.2007.06.008Suche in Google Scholar

[12] T.Savaşkan, M.Ş.Turhal: Mater. Charact.51 (2003) 259. 10.1016/j.matchar.2003.12.003Suche in Google Scholar

[13] T.Savaşkan, Y.Alemdağ: Mater. Sci. Eng. A496 (2008) 517. 10.1016/j.msea.2008.06.008Suche in Google Scholar

[14] M.Ş.Turhal, T.Savaşkan: J. Mater. Sci.38 (2003) 2639. 10.1023/A:1024434602540Suche in Google Scholar

[15] T.Savaşkan, M.Ş.Turhal, S.Murphy: Mater. Sci. Technol.19 (2003) 67. 10.1179/026708303225008644Suche in Google Scholar

[16] T.Savaşkan, A.Aydıner: Wear257 (2004) 377. 10.1016/j.wear.2004.01.007Suche in Google Scholar

[17] B.K.Prasad: Wear257 (2004) 1137. 10.1016/j.wear.2004.07.006Suche in Google Scholar

[18] Y.H.Zhu, W.B.Lee: Mater. Sci. Eng. A293 (2000) 95. 10.1016/S0921-5093(00)01046-7Suche in Google Scholar

[19] B.Bobic, J.Bajat, Z.Acimovic-Pavlovic, M.Rakin, I.Bobic: Corros. Sci.53 (2011) 409. 10.1016/j.corsci.2010.09.051Suche in Google Scholar

[20] Y.Liu, H.Li, H.Jiang, X.Lu: Trans. Nonferrous Met. Soc. China23 (2013) 642. 10.1016/S1003-6326(13)62511-XSuche in Google Scholar

[21] M.Babic, S.Mitrovic, B.Jeremic: Tribol. Int.43 (2010) 16. 10.1016/j.triboint.2009.04.016Suche in Google Scholar

[22] Z.Azaklı, T.Savaşkan: Tribol. Int.41 (2008) 9. 10.1016/j.triboint.2007.04.002Suche in Google Scholar

[23] E.Acer, E.Çadırlı, H.Erol, T.Kırındı, M.Gündüz: Mater. Sci. Eng. A, 662 (2016) 144. 10.1016/j.msea.2016.03.073Suche in Google Scholar

[24] T.Savaşkan, M.Aydın, H.A.Odabaşıoğlu: Mater. Sci. Technol.17 (2001) 681. 10.1179/026708301101510393Suche in Google Scholar

[25] M.Aydın, T.Savaşkan: Int. J. Fatigue26 (2004) 103. 10.1016/S0142-1123(03)00091-4Suche in Google Scholar

[26] T.Savaşkan, M.Aydın: Mater. Charact.52 (2004) 269. 10.1016/j.matchar.2004.05.008Suche in Google Scholar

[27] M.Aydın: J. Mater. Process. Technol.212 (2012) 1780. 10.1016/j.jmatprotec.2012.03.027Suche in Google Scholar

[28] M.Aydın, Y.Heyal: Mater. Sci. Technol.29 (2013) 679. 10.1179/1743284712Y.0000000172Suche in Google Scholar

[29] Y.H.Zhu, F.E.Goodwin: J. Mater. Res.10 (1995) 1927. 10.1557/JMR.1995.1927Suche in Google Scholar

[30] Y.H.Zhu, H.C.Man, H.J.Dorantes-Rosales, W.B.Lee: J. Mater. Sci.38 (2003) 2925. 10.1023/A:1024457109307Suche in Google Scholar

[31] S.Murphy: Met. Sci.9 (1975) 163. 10.1179/030634575790444414Suche in Google Scholar

[32] Z.Zhongming, W.Jincheng, Y.Gencang, Z.Yaohe: J. Mater. Sci.35 (2000) 3383. 10.1023/A:1004885002887Suche in Google Scholar

[33] T.Savaşkan, A.P.Hekimoğlu: Int. J. Mater. Res.106 (2015) 481. 10.3139/146.111207Suche in Google Scholar

[34] A.P.Hekimoğlu, T.Savaşkan: Int. J. Mater. Res.105 (2014) 1084. 10.3139/146.111116Suche in Google Scholar

[35] M.Gholami, J.Vesely, I.Altenberger, H.-A.Kuhn, M.Wollmann, M.Janecek, L.Wagner: Mater. Sci. Eng. A684 (2017) 524. 10.1016/j.msea.2016.12.082Suche in Google Scholar

[36] G.Purcek, M.Aydin, O.Saray, T.Kucukomeroglu: Mater. Sci. Forum633–634 (2009) 437. 10.4028/www.scientific.net/MSF.633-634.437Suche in Google Scholar

[37] Y.H.Zhu: Mater. Trans.45 (2004) 3083. 10.2320/matertrans.45.3083Suche in Google Scholar

[38] R.Gürbüz, S.P.Alpay: Scr. Metall. Mater.30 (1994) 1373. 10.1016/0956-716X(94)90230-5Suche in Google Scholar

[39] Z.F.Zhang, Z.G.Wang: Acta Mater.51 (2003) 347. 10.1016/S1359-6454(02)00399-3Suche in Google Scholar

[40] S.Nagarjuna, M.Srinivas, K.Balasubramanian, D.S.Sarmat: Int. J. Fatigue19 (1997) 51. 10.1016/S0142-1123(96)00041-2Suche in Google Scholar

Received: 2017-12-01
Accepted: 2018-03-07
Published Online: 2018-07-27
Published in Print: 2018-08-10

© 2018, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Dynamic fragmentation and spheroidization of α phase grains during hot deformation of Ti-6Al-4V alloy
  5. Formation and characterization of hot tearing in AZ series alloys
  6. The effect of quench-aging on the mechanical properties of Zn-27Al-1Cu alloy
  7. Microstructural and mechanical properties of novel β-type Ti–Nb–Ni alloys containing a second phase
  8. Microstructure evolution mechanisms of undercooled Ni80Cu20 alloys
  9. Microstructures and tensile properties of CuZrAlNb metallic glass composites under different cooling rates
  10. Influence of a rare-earth element on the solidification behaviour and mechanical properties of undercooled Al–Si alloys
  11. Microstructure of aluminide coatings on Ti6Al4V alloy produced by the slurry method with inorganic binder
  12. Ultrathin SnO2 nanorod/reduced graphene oxide nanosheet composites for electrochemical supercapacitor applications with excellent cyclic stability
  13. Combustion synthesis and formation mechanism of silver nanoparticles
  14. Phase relationship of the Ag–Zr–Cr system at 1000 and 750°C
  15. Thermal properties of carbonized composite materials based on carbon filled elastomeric matrices
  16. Short Communications
  17. Surface morphology and phase stability of titanium irradiated with 168 MeV 136Xe ions
  18. DGM News
  19. DGM News
https://doi.org/10.3139/146.111665
Schlagwörter für diesen Artikel
Zn–Al alloys; Fatigue; Aging; Mechanical properties

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Dynamic fragmentation and spheroidization of α phase grains during hot deformation of Ti-6Al-4V alloy
  5. Formation and characterization of hot tearing in AZ series alloys
  6. The effect of quench-aging on the mechanical properties of Zn-27Al-1Cu alloy
  7. Microstructural and mechanical properties of novel β-type Ti–Nb–Ni alloys containing a second phase
  8. Microstructure evolution mechanisms of undercooled Ni80Cu20 alloys
  9. Microstructures and tensile properties of CuZrAlNb metallic glass composites under different cooling rates
  10. Influence of a rare-earth element on the solidification behaviour and mechanical properties of undercooled Al–Si alloys
  11. Microstructure of aluminide coatings on Ti6Al4V alloy produced by the slurry method with inorganic binder
  12. Ultrathin SnO2 nanorod/reduced graphene oxide nanosheet composites for electrochemical supercapacitor applications with excellent cyclic stability
  13. Combustion synthesis and formation mechanism of silver nanoparticles
  14. Phase relationship of the Ag–Zr–Cr system at 1000 and 750°C
  15. Thermal properties of carbonized composite materials based on carbon filled elastomeric matrices
  16. Short Communications
  17. Surface morphology and phase stability of titanium irradiated with 168 MeV 136Xe ions
  18. DGM News
  19. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2026 De Gruyter Brill
Heruntergeladen am 2.2.2026 von https://www.degruyterbrill.com/document/doi/10.3139/146.111665/html
Button zum nach oben scrollen