Startseite Research on the creep fracture mechanism of FGH95 Ni-based superalloy
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Research on the creep fracture mechanism of FGH95 Ni-based superalloy

  • Xie Jun , Tian Sugui , Zhou Xiaoming , Su Yong und Liu Jiao
Veröffentlicht/Copyright: 5. November 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 104 Heft 11

Abstract

The creep fracture mechanism of FGH95 superalloy has been investigated by means of microstructure observation and creep behaviour measurement. Results show that, after solution treatment at 1150°C, the coarser γ′ precipitates distribute in the wider regions of previous particle boundaries. As the solution temperature increases to 1165°C, the grains grow in the alloy and carbide films precipitate along the grain boundaries. When the alloy is solution treated at 1160°C, the coarser γ′ phase in boundary regions is fully dissolved, and granular carbides precipitate along the grain boundaries, which may effectively restrain boundary sliding and hinder dislocation movements to improve the creep resistance of the alloy. During creep, the deformation feature of the alloy is that slipping dislocations with single or double orientations and stacking faults are activated in the alloy. As creep progresses, the amount of slip traces increases to bring about stress concentration and cause microcracks to be initiated and propagated along the grain boundaries up to the rupture of the alloy.

Keywords: FGH95 nickel-based superalloy; Microstructure; Creep fracture mechanism
* Correspondence address, Su-gui Tian (Professor), School of Materials Science and Engineering, Shenyang University of Technology, No. 111, Shenliao West Road, Economic and Technological Development Zone, Shenyang, 110870, P. R. China, Tel.: +86-24-25494089, Fax: +86-24-25496768, E-mail:

References

[1] B.F.Hu, G.F.Tian, C.C.Jia, G.Q.Liu: J. Aeronaut. Mater.27 (2007) 80.Suche in Google Scholar

[2] S.Y.Wang, H.Q.Li, H.T.Yang: J. Aeronaut. Mater.27 (2007) 30.Suche in Google Scholar

[3] Z.Huda: Mater. Des.28 (2007) 1664. 10.1016/j.matdes.2006.03.026Suche in Google Scholar

[4] L.W.Lherbier, W.B.Kent: Int. J. Powder Metall.26 (1990) 131.Suche in Google Scholar

[5] S.Raujol, F.Pettinari, D.Locq, P.Caron, A.Coujou, N.Clémen: Mater. Sci. Eng. A387/389 (2004) 678. 10.1016/j.msea.2004.02.091Suche in Google Scholar

[6] S.G.Tian, Y.Liu, X.M.Zhao, Z.G.Zhao, X.Y.Bao, W.X.Wang: Chin. J. Aeronaut.22 (2009) 444. 10.1016/S1000-9361(08)60123-5Suche in Google Scholar

[7] H.M.Chen, B.F.Hu, H.Y.Li, D.Song: Chin. J. Nonferrous Met.13 (2003) 554.Suche in Google Scholar

[8] S.G.Tian, Y.Liu, Z.G.Zhao, X.Y.Bao: J. Aeronaut. Mater.29 (2009) 33.Suche in Google Scholar

[9] B.F.Hu, H.M.Chen, K.S.Jin, H.Y.Li: Chin. J. Nonferrous Met.14 (2004) 901.Suche in Google Scholar

[10] J.Xie, S.G.Tian, X.M.Zhou, W.X.Wang: J. Mater. Eng.S1 (2009) 147.Suche in Google Scholar

[11] F.He, W.X.Wang, W.H.Yang, J.W.Zou, X.Q.Wang, Y.F.Han: J. Aeronaut. Mater.20 (2000) 22.Suche in Google Scholar

[12] Z. Z.Lu, C. L.Liu, Z. F.Yue. Mater. Sci. Eng. A395 (2005) 153. 10.1016/j.msea.2004.12.008Suche in Google Scholar

[13] S.G.Tian, J.Xie, X.M.Zhou, B.J.Qian, J.W.Lun, L.L.Yu, W.X.Wang: Chin. J. Nonferrous Met.20 (2010) 852. 10.1016/S1003-6326(10)60594-8Suche in Google Scholar

[14] P.Lawenstein: Powder Metallurgy Superalloys, (1988) 27.Suche in Google Scholar

[15] P.Wang, J.X.Dong, L.Yang, L.Zheng, S.H.Wei: Mater. Rev.22 (2008) 61.Suche in Google Scholar

[16] S.G.Tian, J.Xie, X.M.Zhou, B.J.Qian, J.W.Lun, L.L.Yu, W.X.Wang: Mater. Sci. Eng. A528 (2011) 2076. 10.1016/j.msea.2010.11.038Suche in Google Scholar

[17] J.Xie, S.G.Tian, X.M.Zhou, J.J.Li, W.X.Wang: Rare Met.30 (2011) 447. 10.1007/s12598-011-0246-0Suche in Google Scholar

[18] S.G.Tian, X.F.Yu, J.H.Yang, N.R.Zhao, Y.B.Xu, Z.Q.Hu: Mater. Sci. Eng. A379 (2004) 141. 10.1016/j.msea.2004.01.049Suche in Google Scholar

[19] Y.W.Zhang, Y.Zhang, F.G.Zhang, S.Z.Yang: Trans. Mater. Heat Treat.23 (2002) 72.Suche in Google Scholar

[20] J.S.Zhang: High Temperature Deformation and Fracture of Material, Science Press, Beijing (2007). 10.1515/HTMP.2007.26.2.139Suche in Google Scholar

Received: 2012-10-09
Accepted: 2013-06-24
Published Online: 2013-11-05
Published in Print: 2013-11-14

© 2013, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Solubility of nitrogen in ferrite; the Fe–N phase diagram
  5. The Li–C phase equilibria
  6. Experimental study of phase equilibria in the “SnO”–SiO2–“FeO” system at silica saturation, and fixed oxygen partial pressures at 1473 K
  7. The evolution of Y distribution during the processing route of mechanically alloyed iron studied by means of atom probe tomography
  8. Oscillative surface morphology in peritectic NiAl using phase-field modeling
  9. Microstructural characterisation of oxide layer developed by sulphuric anodisation on 2017A alloys
  10. Wear and corrosion behaviour of AISI 310 and AISI 316 stainless steels in synthetic mine water
  11. Superplasticity of coarse-grained Ti-13V-11Cr-3Al alloy
  12. Research on the creep fracture mechanism of FGH95 Ni-based superalloy
  13. Hot pressing of Al2O3 matrix ceramic materials improved by diopside additive
  14. Tungsten heavy alloy as a filler metal for repair welding of dies for high pressure die casting
  15. A one-pot synthesis of Ag/α-Fe2O3 nanoplates with gelatin and their photocatalytic activity
  16. Short Communications
  17. Effects of coating solution concentration on the interlaminar shear strength of carbon fiber/epoxy/nano-CaCO3 composites
  18. People
  19. Dr.-Ing. Christa Blank
  20. DGM News
  21. DGM News
https://doi.org/10.3139/146.110971
Schlagwörter für diesen Artikel
FGH95 nickel-based superalloy; Microstructure; Creep fracture mechanism

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Solubility of nitrogen in ferrite; the Fe–N phase diagram
  5. The Li–C phase equilibria
  6. Experimental study of phase equilibria in the “SnO”–SiO2–“FeO” system at silica saturation, and fixed oxygen partial pressures at 1473 K
  7. The evolution of Y distribution during the processing route of mechanically alloyed iron studied by means of atom probe tomography
  8. Oscillative surface morphology in peritectic NiAl using phase-field modeling
  9. Microstructural characterisation of oxide layer developed by sulphuric anodisation on 2017A alloys
  10. Wear and corrosion behaviour of AISI 310 and AISI 316 stainless steels in synthetic mine water
  11. Superplasticity of coarse-grained Ti-13V-11Cr-3Al alloy
  12. Research on the creep fracture mechanism of FGH95 Ni-based superalloy
  13. Hot pressing of Al2O3 matrix ceramic materials improved by diopside additive
  14. Tungsten heavy alloy as a filler metal for repair welding of dies for high pressure die casting
  15. A one-pot synthesis of Ag/α-Fe2O3 nanoplates with gelatin and their photocatalytic activity
  16. Short Communications
  17. Effects of coating solution concentration on the interlaminar shear strength of carbon fiber/epoxy/nano-CaCO3 composites
  18. People
  19. Dr.-Ing. Christa Blank
  20. DGM News
  21. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 17.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.110971/pdf
Button zum nach oben scrollen