Characterization of polypropylene/magnesium oxide/vapor-grown carbon fiber composites prepared by melt compounding
-
Shuichi Tanoue
und
Hideyuki Uematsu
Abstract
In this paper, we discussed the characteristics and properties of polypropylene (PP)/magnesium oxide (MgO) composites prepared by melt compounding. In addition, we also discussed the effect of adding vapor-grown carbon fiber (VGCF) to PP/MgO composite on the properties of the composites. The thermal conductivity of PP/MgO increased with MgO content. In the region of MgO content of more than 30 vol%, the thermal conductivity of PP/MgO with MgO-10 (particle size of 10 μm) is the largest by comparison of other PP/MgO with different MgO sizes. The thermal conductivity of PP/MgO became increased by adding VGCF in PP/MgO. According to the estimation of thermal conductivity using Bruggeman’s equation, no synergistic effect was observed by adding VGCF into the PP/MgO composite. The surface resistance of PP/MgO significantly decreased by adding VGCF at a content of more than 3 vol%. At VGCF content of 1 vol%, the surface resistance of the composite became large, and the value was more than 109 Ω/sq. In addition, the Non-Newtonian property of PP/MgO composite melt was enhanced by the addition of VGCF into the composite.
Acknowledgments
We express our thanks to Ms. Chihiro Azuma and Mr. Masahiro Komura, past students of Graduate School of Engineering, University of Fukui, Japan for doing the experiments and measurements in this study.
-
Author contribution: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Research funding: None declared.
-
Conflict of interest statement: The authors declare that they have no conflicts of interest regarding this article.
References
1. Zhang, X., Wu, H., Guo, S., Wang, Y. Understanding in crystallization of polyethylene: the role of boron nitride (BN) particles. RSC Adv. 2015, 5, 99812–99819. https://doi.org/10.1039/c5ra19982d.Suche in Google Scholar
2. Mosanenzadeh, S. G., Liu, M. W., Osia, A., Naguib, H. E. Thermal composites of biobased polyamide with boron nitride micro networks. J. Polym. Environ. 2015, 23, 566–579.10.1007/s10924-015-0733-8Suche in Google Scholar
3. Ghahramani, N., Esfahani, S. A. S., Mehranpour, M., Nazockdast, H. The effect of filler localization on morphology and thermal conductivity of the polyamide/cyclic olefin copolymer blends filled with boron nitride. J. Mater. Sci. 2018, 53, 16146–16159. https://doi.org/10.1007/s10853-018-2746-x.Suche in Google Scholar
4. Quill, T. J., Smith, M. K., Zhou, T., Baioumy, M. G. S., Berenguer, J. P., Cola, B. A., Kalaitzidou, K., Bougher, T. L. Thermal and mechanical properties of 3D printed boron nitride – ABS composites. Appl. Compos. Mater. 2018, 25, 1205–1217. https://doi.org/10.1007/s10443-017-9661-1.Suche in Google Scholar
5. Cheewawuttipong, W., Fuoka, D., Tanoue, S., Uematsu, H., Iemoto, Y. Thermal and mechanical properties of polypropylene/boron nitride composites. Energy Proc. 2013, 34, 808–817. https://doi.org/10.1016/j.egypro.2013.06.817.Suche in Google Scholar
6. Cheewawuttipong, W., Fuoka, D., Tanoue, S., Uematsu, H., Iemoto, Y. Thermal conductivity of polypropylene composites with combined boron nitride fillers. Int. Polym. Process. 2014, 29, 214–220. https://doi.org/10.3139/217.2833.Suche in Google Scholar
7. Yu, C., Zhang, J., Tian, W., Fan, X., Yao, Y. Polymer composites based on hexagonal boron nitride and their application in thermally conductive composites. RSC Adv. 2018, 8, 21948–21967. https://doi.org/10.1039/c8ra02685h.Suche in Google Scholar PubMed PubMed Central
8. Gaska, K., Xu, X., Gubanski, S., Kadar, R. Electrical, mechanical, and thermal properties of LDPE graphene nanoplatelets composites produced by means of melt extrusion process. Polymers 2017, 9, 11. https://doi.org/10.3390/polym9010011.Suche in Google Scholar PubMed PubMed Central
9. Araby, S., Zaman, I., Meng, Q., Kawashima, N., Michelmore, A., Kuan, H. C., Majewski, P., Ma, J., Zhang, L. Melt compounding with graphene to develop functional, high-performance elastomers. Nanotechnology 2013, 24, 165601. https://doi.org/10.1088/0957-4484/24/16/165601.Suche in Google Scholar PubMed
10. Wondu, E., Lule, Z., Kim, J. Thermal conductivity and mechanical properties of thermoplastic polyurethane-/silane-modified Al2O3 composite fabricated via melt compounding. Polymers 2019, 11, 1103. https://doi.org/10.3390/polym11071103.Suche in Google Scholar PubMed PubMed Central
11. Pak, S. Y., Kim, H. M., Kim, S. Y., Youn, J. R. Synergistic improvement of thermal conductivity of thermoplastic composites with mixed boron nitride and multi-walled carbon nanotube fillers. Carbon 2012, 50, 4830–4838. https://doi.org/10.1016/j.carbon.2012.06.009.Suche in Google Scholar
12. Xiao, Y., Wang, W., Chen, X., Zhang, Y., Yang, J., Wang, Y., Zhou, Z. Largely enhanced thermal conductivity and high dielectric constant of poly(vinylidene fluoride)/boron nitride composites achieved by adding a few carbon nanotubes. J. Phys. Chem. 2016, 120, 6344–6355. https://doi.org/10.1021/acs.jpcc.5b12651.Suche in Google Scholar
13. Cheewawuttipong, W., Tanoue, S., Uematsu, H., Iemoto, Y. Thermal conductivity of polypropylene composites with hybrid fillers of boron nitride and vapor-grown carbon fiber. Polym. Compos. 2016, 37, 936–942. https://doi.org/10.1002/pc.23252.Suche in Google Scholar
14. Qamarina, M. S. N., Kawahara, S. Effect of Mg oxide nanoparticles on sulphur vulcanisation of natural rubber. J. Rubber Res. 2014, 17, 13–22.Suche in Google Scholar
15. Imai, Y., Kodama, N., Takahashi, S., Kan, A., Hotta, Y., Ogawa, H. Suppression of dielectric loss of PPE/HIPS alloys in microwave region by utilization of MgO filler. J. Appl. Polym. Sci. 2019, 136, 47315. https://doi.org/10.1002/app.47315.Suche in Google Scholar
16. Dong, Q., Gao, C., Ding, Y., Wang, F., Wen, B., Zhang, S., Wang, T., Yang, M. A polycarbonate/magnesium oxide nanocomposite with high flame retardancy. J. Appl. Polym. Sci. 2012, 123, 1085–1093. https://doi.org/10.1002/app.34574.Suche in Google Scholar PubMed PubMed Central
17. Lin, X., Wu, Y., Tang, L. Y., Yang, M. H., Ren, D. Y., Zha, J. W., Dang, Z. M. Experimental study of the rheological, mechanical, and dielectric properties of MgO/LDPE nanocomposites. J. Appl. Polym. Sci. 2016, 133, 43038. https://doi.org/10.1002/app.43038.Suche in Google Scholar
18. Bruggeman, D. A. G. Berechnung verschiedener physikalischer Konstanten von heterogenen Substanzen. I. Dielektrizitätskonstanten und Leitfähigkeiten der Mischkörper aus isotropen Substanzen. Ann. Phys. 1935, 416, 636–664. https://doi.org/10.1002/andp.19354160705.Suche in Google Scholar
19. Tanoue, S., Nithikaranjanatharn, J., Okuzono, H., Ueda, H., Uematsu, H., Iemoto, Y. Effect of screw rotation speed on the properties of polycarbonate/vapor-grown carbon fiber composites prepared by melt compounding. Int. Polym. Process. 2014, 29, 41–50. https://doi.org/10.3139/217.2799.Suche in Google Scholar
20. Lertwimolnun, W., Vergnes, B. Influence of compatibilizer and processing conditions on the dispersion of nanoclay in a polypropylene matrix. Polymer 2005, 46, 3462–3471. https://doi.org/10.1016/j.polymer.2005.02.018.Suche in Google Scholar
21. Domenech, T., Zouari, R., Vergnes, B., Peuvrel-Disdier, E. Formation of fractal-like structure in organoclay-based polypropylene nanocomposites. Macromolecules 2014, 47, 3417–3427. https://doi.org/10.1021/ma5001354.Suche in Google Scholar
© 2021 Walter de Gruyter GmbH, Berlin/Boston
Artikel in diesem Heft
- Frontmatter
- Material Properties
- Morphology, thermal and mechanical properties of electrospun polyvinylidene/polyethylene glycol composite nanofibers as form-stabilized phase change materials
- Design of experiments for the methylene blue adsorption study onto biocomposite material based on Algerian earth chestnut and cellulose derivatives
- Characterization of polypropylene/magnesium oxide/vapor-grown carbon fiber composites prepared by melt compounding
- Preparation and Assembly
- Toughened poly(lactic acid)/thermoplastic polyurethane uncompatibilized blends
- Preparation of hydrophilic modified polyvinylidene fluoride (PVDF) ultrafiltration membranes by polymer/non-solvent co-induced phase separation: effect of coagulation bath temperature
- Fabrication of inverted organic solar cells on stainless steel substrate with electrodeposited and spin coated ZnO buffer layers
- Engineering and Processing
- A review on 3D printing in tissue engineering applications
- Application of radiation grafted waste polypropylene fabric for the effective removal of Cu (II) and Cr (III) ions
Artikel in diesem Heft
- Frontmatter
- Material Properties
- Morphology, thermal and mechanical properties of electrospun polyvinylidene/polyethylene glycol composite nanofibers as form-stabilized phase change materials
- Design of experiments for the methylene blue adsorption study onto biocomposite material based on Algerian earth chestnut and cellulose derivatives
- Characterization of polypropylene/magnesium oxide/vapor-grown carbon fiber composites prepared by melt compounding
- Preparation and Assembly
- Toughened poly(lactic acid)/thermoplastic polyurethane uncompatibilized blends
- Preparation of hydrophilic modified polyvinylidene fluoride (PVDF) ultrafiltration membranes by polymer/non-solvent co-induced phase separation: effect of coagulation bath temperature
- Fabrication of inverted organic solar cells on stainless steel substrate with electrodeposited and spin coated ZnO buffer layers
- Engineering and Processing
- A review on 3D printing in tissue engineering applications
- Application of radiation grafted waste polypropylene fabric for the effective removal of Cu (II) and Cr (III) ions
