Volume 11, Issue 21

A novel fiber-tip micro flowmeter based on optofluidic microcavity filled with silver nanoparticles solutions (SNS) is proposed. CW fiber laser was used to heat SNS that can emit heat obviously due to the excellent optic-thermo effect. The heat generated by the silver nanoparticles would be taken away as the microfluidic flows over the fiber microcavity until thermal balance is established under different velocity. The effective refractive index (RI) of the SNS changed followed by temperature of the thermal balance. The dips of the Fabry–Perot interference spectrum shift and the flow velocity can be demodulated. Moreover, the sensor can measure the flow rate with a high sensitivity due to the superior thermal conductivity and specific heat capacity of sidewalls. The max flow rate sensitivity can reach 1.5 nm/(μL/s) in the large range of 0–5 μL/s with a detection limitation (DL) of 0.08 μL/s. The Micron scale probe-type flowmeter has strong robustness and can be used to measure flow rate in tiny space. The heating medium also has an excellent biological compatibility and is not contact with the fluidics directly. As such, we believe that the proposed fiber-tip micro flowmeter has great application potentials in haematology, oil prospecting, ocean dynamics and drug research.

Integration of multiple diversified functionalities into an ultracompact platform is crucial for the development of on-chip photonic devices. Recently, a promising all-dielectric two-dimensional platform based on Bloch surface waves (BSWs) sustained by dielectric multilayer has been proposed to enable various functionalities and provide novel approach to photonic devices. Here, we design and fabricate a multifunctional directional coupler to achieve both spectral and polarimetric routing by employing asymmetric nanoslits in a dielectric multilayer platform. Due to the dispersion property of BSWs, the directional coupling behavior is sensitive to wavelength and polarization. We demonstrate numerically and experimentally the wavelength selective directional coupling of TE BSW mode with an intensity ratio of the BSW excitation in opposite directions reaching 10 dB. Polarization selective directional coupling is also achieved at specific operating wavelength due to different response to a nanoantenna for TE and TM BSWs. The proposed two-dimensional photonic device opens new pathway for a wide range of practical applications such as molecular sensing, imaging with different polarization, and spectral requirements.

The proper design of near-infrared light-absorbing agents enables efficient optoacoustic imaging-guided phototherapy. In particular, several croconaine-based organic agents with excellent optical properties have been recently reported for this purpose. However, most of them absorb light below 800 nm, limiting deep-tissue imaging applications. To this end, we utilized a recently described novel croconaine derivative (CR880) to develop CR880-based nanoparticles (CR880-NPs) for effective in vivo delivery, deep tissue optoacoustic imaging and photothermal therapy applications. Radicals and strong π – π stacking in CR880 result in an 880 nm absorption peak with no blue-shift upon condensing to the solid phase. DSPE-PEG2000-formulated CR880-NPs exhibited high optoacoustic generation efficiency and photostability, and could be visualized in the tumors of three different mouse tumor models (breast, brain, and colon tumor) with high image contrast. The high photothermal conversion efficiency of CR880-NPs (∼58%) subsequently enabled efficient in vivo tumor elimination using a low energy laser, while remaining biocompatible and well-tolerated. This work introduces a promising novel agent for cancer theranostics of challenging deep-seated tumors.

Scanned reactive-ion-beam etching method was proposed to transfer two-dimensional mask patterns into quartz substrate, which would produce a larger-size and polarization-independent two-dimensional grating. This method was realized by moving grating substrate in a unidimensional scanning manner and adjusting ion beam density in the vertical scanning direction. Graphite plates between the ion beam source and the substrate were used to correct the beam density. The original Gaussian ion beam density was changed to a uniform distribution to establish a knife-edge shape around the vertical scanning direction. Therefore, a large-area pattern with consistent depth and duty cycle would be engraved into a quartz substrate. A two-dimensional, 1200 groves/mm grating with an 85-mm × 85-mm area was fabricated under scanned reactive-ion-beam etching method and exhibited a 0.197 λ ( λ = 632.8 nm) diffraction wave front. At 780 nm, the efficiency nonuniformity was less than 9%, and the average diffraction efficiencies of transverse-magnetic and transverse-electric polarized light were 57.2 and 58.0%, respectively. The large-size two-dimensional grating with uniform diffraction efficiency and polarization independence enabled grating displacement measurement with high resolution, long measurement range, multiple degrees of freedom, and potential miniaturization.

The generation of nonclassical light states bears a paramount importance in quantum optics and is largely relying on the interaction between intense laser pulses and nonlinear media. Recently, electron beams, such as those used in ultrafast electron microscopy to retrieve information from a specimen, have been proposed as a tool to manipulate both bright and dark confined optical excitations, inducing semiclassical states of light that range from coherent to thermal mixtures. Here, we show that the ponderomotive contribution to the electron–cavity interaction, which we argue to be significant for low-energy electrons subject to strongly confined near-fields, can actually create a more general set of optical states, including coherent and squeezed states. The postinteraction electron spectrum further reveals signatures of the nontrivial role played by A 2 terms in the light–matter coupling Hamiltonian, particularly when the cavity is previously excited by either chaotic or coherent illumination. Our work introduces a disruptive approach to the creation of nontrivial quantum cavity states for quantum information and optics applications, while it suggests unexplored possibilities for electron beam shaping.

Exploiting localized heat-generation density and the resulting enhanced temperature-rise for controlled growth of carbon nanotubes (CNTs) is reported, and its potentials for batch-production of high-quality CNT probes are demonstrated. Optical near field chemical vapor deposition (ONF-CVD) benchtop fabrication schemes are developed for the localized integration of individual well-aligned carbon nanotubes without bending/buckling exactly at desired nanoscale sites. It is demonstrated that generating self-aligned catalyst nanoparticles superimposed on top of silicon nanotips, along with near-field induced absorption confinement, provide the ability to localize the generated heat at the nanotips apexes, and control the CNT growth locations. The nanoscale maskless controllability of the growth site is shown by properly tailoring ONF-CVD conditions to overcome overall heat exposure of the substrate for selective activation of catalyst nanoparticles located at apexes, from those dispersing all over the tips. The calculated local power densities and temperature profiles of the simulated tips, clearly demonstrate the confined heat and optimal gradient of generated temperature rise as the main factors affecting the growth. In addition to determining necessary processing conditions to control the localization and orientation of the growth, parameters affecting the length and diameter of the localized individually grown nanotubes are also presented. Optical near-field-based growth schemes can be extended for localized maskless fabrication of other nanoscale devices, beyond the diffraction limit, using photothermal effects.

The emerging applications of silicon photonics in free space, such as LiDARs, free-space optical communications, and quantum photonics, urge versatile emission shaping beyond the capabilities of conventional grating couplers. In these applications, silicon photonic chips deliver free-space emission to detect or manipulate external objects. Light needs to emit from a silicon photonic chip to the free space with specific spatial modes, which produce focusing, collimation, orbital angular momentum, or even holographic projection. A platform that offers versatile shaping of free-space emission, while maintaining the CMOS compatibility and monolithic integration of silicon photonics is in pressing need. Here we demonstrate a platform that integrates metasurfaces monolithically on silicon photonic integrated circuits. The metasurfaces consist of amorphous silicon nanopillars evanescently coupled to silicon waveguides. We demonstrate experimentally diffraction-limited beam focusing with a Strehl ratio of 0.82. The focused spot can be switched between two positions by controlling the excitation direction. We also realize a meta-hologram experimentally that projects an image above the silicon photonic chip. This platform can add a highly versatile interface to the existing silicon photonic ecosystems for precise delivery of free-space emission.

We demonstrated silicon-on-insulator (SOI)-based high-efficiency metalenses at telecommunication wavelengths that are integrable with a standard 220 nm-thick silicon photonic chip. A negative electron-beam resist (ma-N) was placed on top of the Si nanodisk, providing vertical symmetry to realize high efficiency. A metasurface with a Si/ma-N disk array was numerically investigated to design a metalens that showed that a Si/ma-N metalens could focus the incident beam six times stronger than a Si metalens without ma-N. Metalenses with a thick ma-N layer have been experimentally demonstrated to focus the beam strongly at the focal point and have a long depth of field at telecommunication wavelengths. A short focal length of 10 μm with a wavelength-scale spot diameter of approximately 2.5 μm was realized at 1530 nm. This miniaturized high-efficiency metalens with a short focal length can provide a platform for ultrasensitive sensors on silicon photonic IC.

Based on the 3D Dirac semimetals (DSM) supported tilted double elliptical resonators, the tunable propagation properties of quasi-bound in continuum (BIC) resonance have been investigated in the THz regime, including the effects of rotation angles, DSM Fermi level, and the configuration of resonators. The results manifest that by altering the rotation angle of elliptical resonator, an obvious sharp BIC transmission dip is observed with the Q -factor of more than 60. The DSM Fermi level affects the BIC resonance significantly, a sharp resonant dip is observed if Fermi level is larger than 0.05 eV, resulting from the contributions of reflection and absorption. If Fermi level changes in the range of 0.01–0.15 eV, the amplitude and frequency modulation depths are 92.75 and 44.99%, respectively. Additionally, with the modified configurations of elliptical resonators, e.g. inserting a dielectric hole into the elliptical resonator, another transmission dip resonance is excited and indicates a red shift with the increase of the permittivity of the dielectric filling material. The results are very helpful to understand the mechanisms of DSM plasmonic structures and develop novel tunable THz devices, such as modulators, filters, and sensors in the future.

Polystyrene (PS) is generally considered as a passive optical material that is transparent to light with wavelengths longer than 300 nm. In practice, PS micro- and nanospheres with uniform sizes are usually used to build photonic crystals based on self-assembly mechanism. Here, we demonstrate experimentally that PS microspheres supporting whispery gallery modes can be transformed into multimode light sources by laser irradiation. We show that a PS microsphere placed on a silica substrate can be lighted up when it is consecutively irradiated by using a 488-nm continuous wave laser beam with a pumping power above a threshold. Broadband luminescence emitted from the PS microsphere increases rapidly to a maximum value and decreases gradually with increasing irradiation time, implying the generation and degradation of a certain luminescent material upon laser irradiation. However, the PS microsphere is found to be damaged by high temperature based on morphology examination. By replacing the silica substrate with a thin silver film, the threshold laser power for lighting up a PS microsphere is dramatically reduced. More importantly, we can see enhanced luminescence intensities from the whispery gallery modes supported by the PS microsphere, which becomes an efficient multimode light source. Interestingly, the threshold laser power can be further lowered by inserting a molybdenum disulfide monolayer in between the PS microsphere and the silver film. As a result, the PS microsphere remains nearly unchanged except the formation of the luminescence material. Our findings open a new horizon for the interaction of polymer with laser light by exploiting the optical resonances supported by micro- and nanoparticles and pave the way for constructing photonic devices based on laser-induced luminescent materials in polymers.

Holograms hidden inside transparent materials are important for information encryption storage because of their advantages of secrecy, and could completely avoid information loss caused by surface wear. Inside the transparent material, the modified filaments array was need for hologram fabrication to change the optical phase or amplitude of incident laser, which is sensitive to the change of refractive index. Then the uniformity of modified filaments inside transparent materials is highly required. In this study, by tuning the interval time of the double-pulse processing, holograms with improved imaging quality were fabricated by double-pulse femtosecond laser and the effect and mechanism of self-trapped excitons (STEs) on the ablation have been systematically studied. The imaging quality of the hologram fabricated with double-pulse laser was superior to that of the one fabricated with the single-pulse laser and 350 fs was verified to be the best time interval for double-pulse processing. The evolution of the electrons dynamics was investigated by using the pump-probe technology. With the double-pulse time interval increasing, the residual electrons, excitons, STEs, and defects caused by the first sub-pulse would become dominated sequentially. The results demonstrated the controllability of STEs and quality improvement of final structures by double-pulse femtosecond laser processing.

Terahertz detectors based on two-dimensional Dirac materials offer a new approach for room-temperature terahertz detection with high response and low noise. However, these devices can hardly show high response over a broad frequency range, mainly due to the poor absorption caused by their ultrathin nature. Here we apply metallic gratings to enhance the excitation efficiency of graphene plasmons. When nonzero source-drain bias is applied, graphene plasmons can generate terahertz response orthogonal to the polarization of the incidence. The response is attributed to the orthogonal overdamped plasmon rectification effect, and graphene plasmons-enhanced photo-thermoelectric effect. By comparing the normalized on/off ratio, the metallic gratings are found to effectively enhance the coupling efficiency between graphene plasmons and THz incidence, and thus the absorption and responsivity. The results are beneficial for improving the response of room temperature THz detectors.

Optical materials with nearly zero refractive indices have driven emerging applications ranging from geometry-invariant optical tunneling, nonlinear optics, optical cloaking to thermal emission manipulation. In conventional dielectric photonic circuits, light scattering and back reflection at the waveguide bends and crossings leads to significant optical loss. Here we propose to use near-zero-index materials as a cladding layer for low-loss optical waveguides, where optical modes are tightly confined within the dielectric core region. Compared to conventional waveguides, the near-zero-index waveguides are superior in maintaining a high mode-filling factor for small device sizes close to the diffraction limit and reducing the crosstalk in between at a sub-wavelength separation. In addition, we found that light propagation is robust to waveguide bends in a small radius (∼µm) and geometry variation in the cross section. Hollow waveguides with near-zero-index cladding layers further support low-loss light propagation because materials absorption is minimized from the air core. Our work offers critical insights into future designs of low-loss and miniaturized photonic devices.

High index dielectric nanoresonators have gained prominence in nanophotonics due to lower losses compared to plasmonic systems and their ability to sustain both electric and magnetic resonances. The resonances can be engineered to create new types of optical states, such as bound-states in a continuum (BIC) and anapoles. In this work, we report on the optical properties of vertically stacked AlGaAs nanodisk Mie resonators. The nanodisks are designed to support an anapole state in the visible wavelength region (400–700 nm). The vertically stacked nanodisk resonators are fabricated from AlGaAs/GaAs multilayer samples with a fast and scalable patterning method using charged sphere colloidal lithography. Both measurements and finite difference time domain (FDTD) simulations of two and three stacked resonators show a sharp dip in the reflectance spectra at the anapole wavelength. For the 2 and 3 disk stacks the reflectance dip contrast at the anapole wavelength becomes very pronounced in the specular reflectance and is attributed to increased directional scattering due to an antenna effect. FDTD simulations show there is enhanced field confinement in all the disks at the anapole wavelength and the confined energy within the individual disks in the stack is at least 2–5 times greater compared to an isolated single nanodisk of the same dimension. Furthermore, the field confinement consistently increases with adding more disks in the stack. These vertically stacked AlGaAs nanodisk resonators can be a very exciting platform to engineer light matter interactions for linear and non-linear optical applications. The general principles of the fabrication method can be adapted to other wavelength ranges and can also be adapted for other III–V material combinations as well as for Si/SiO 2 .

Recently, the study of topological structures in photonics has garnered significant interest, as these systems can realize robust, nonreciprocal chiral edge states and cavity-like confined states that have applications in both linear and nonlinear devices. However, current band theoretic approaches to understanding topology in photonic systems yield fundamental limitations on the classes of structures that can be studied. Here, we develop a theoretical framework for assessing a photonic structure’s topology directly from its effective Hamiltonian and position operators, as expressed in real space, and without the need to calculate the system’s Bloch eigenstates or band structure. Using this framework, we show that nontrivial topology, and associated boundary-localized chiral resonances, can manifest in photonic crystals with broken time-reversal symmetry that lack a complete band gap, a result that may have implications for new topological laser designs. Finally, we use our operator-based framework to develop a novel class of invariants for topology stemming from a system’s crystalline symmetries, which allows for the prediction of robust localized states for creating waveguides and cavities.

Quantum dots (QDs) often exhibit unique behaviors because the reduction in lateral size leads to stronger quantum confinement effects and a higher surface-to-volume ratio in comparison with larger two-dimensional nanosheets. However, the preparation of homogeneous QDs remains a longstanding challenge. This work reports the preparation of high-yield and ultrasmall tin disulfide (SnS 2 ) QDs by combining top–down and bottom–up approaches. The as-prepared SnS 2 QDs have a uniform lateral size of 3.17 ± 0.62 nm and a thicknesses 2.39 ± 0.88 nm. A series of self-powered photoelectrochemical-type photodetectors (PDs) utilizing the SnS 2 QDs as photoelectrodes are also constructed. Taking advantage of the tunable bandgaps and high carrier mobility of the SnS 2 , our PDs achieve a high photocurrent density of 16.38 μA cm −2 and a photoresponsivity of 0.86 mA W −1 , and good long-term cycling stability. More importantly, the device can display obvious photoresponse, even at zero bias voltage (max), and greater weak-light sensitivity than previously reported SnS 2 -based PDs. Density functional theory calculation and optical absorption were employed to reveal the working mechanism of the SnS 2 QDs-based PDs. This study highlights the prospective applications of ultrasmall SnS 2 QDs and provides a new route towards future design of QDs-based optoelectronic devices.

GaInN/GaN multi-quantum-shell (MQS) nanowires (NWs) are gaining increasing attention as promising materials for developing highly efficient long-wavelength micro-light emitting diodes (LEDs). To improve the emission properties in GaInN/GaN MQS NWs, it is necessary to suppress the emission from the (0001) c -plane MQS at the apex region, which featured with low crystalline quality. In this study, we investigated the enhancement of optical properties and the realization of micro-LEDs by confirming the effect of the (0001) plane region. A 7.9-fold enhancement of the electroluminescence (EL) intensity was demonstrated by removal the (0001) plane region via inductively coupled plasma (ICP) dry etching, owing to the promoted current injection into the (1–101) semi-polar and (10–10) non-polar sidewall area. To investigate the effect of the emission area on the samples with and without truncated (0001) plane region, devices with three different mesa areas (50 × 50, 100 × 100, and 100 × 200 μm 2 ) were fabricated. An increased EL intensity with the reduced mesa areas was observed in the samples without dry etching of the (0001)-plane area, because more current can be injected into the sidewall region with higher crystalline quality and luminous efficiency than the (0001)-plane MQS. Under the same injection current density, the truncated samples’ light output was increased for more than ten times as compared to the samples without (0001)-plane etching. Therefore, it confirms the possibility of realizing highly efficient GaInN/GaN MQS NWs LEDs by eliminating the (0001) plane MQS region. A precise etching and surface passivation of the apex region is expected to further reduce the reverse leakage current and improve the performance in NW-LEDs.

Near-field optics is essential in many nanotechnology applications, such as implementing sensitive biosensing and imaging systems with extreme precision. Understanding optical near-fields at the nanoscale has so attracted the considerable research interest, which use a variety of analytical approaches, most notably near-field scanning microscopy. Here, we show defocused point localization mapped accumulation (DePLOMA), which can overcome many weaknesses of conventional analytical methods. DePLOMA is based on imaging fluorescence emitters at an out-of-focal plane. The acquisition, collection, and accumulation of the position and fluorescence intensity of emitters moving above nanostructures can generate three-dimensional near-field maps of light distribution. The idea enables super-resolution liquid-phase measurements, as demonstrated by reconstruction of near-field created by nanoslits with a resolution determined by emitter size. We employed fluorescent emitters with a radius of 50 and 100 nm for confirmation. The axial resolution was found to be enhanced by more than 6 times above that of diffraction-limited confocal laser scanning microscopy when DePLOMA was used.

Quantitative molecular detection based on surface-enhanced Raman spectroscopy (SERS) is still a great challenge because of the highly nonuniform distribution of the SERS hot spots and the nondeterministic spatial and spectral overlap of the analyte with the hot spot. Here, we report a nanoparticle-on-mirror plasmonic sensor excited by surface plasmon polaritons for quantitative SERS detection of alpha fetoprotein in serum with ultrahigh sensitivity. The uniform gaps between the nanoparticles and gold film and the alignment of the gap modes relative to the excitation electric field endow this substrate with a uniform and strong SERS enhancement. The limit of detection reaches 1.45 fM, 697 times higher than that under normal excitation and 7800 times higher than a commercial enzyme-linked immunosorbent assay kit. This approach offers a potential solution to overcome the bottleneck in the field of SERS-based biosensing.

With the insertion a segment of polarization-maintaining fiber (PMF) inside the cavity, abundant dynamics of group velocity locked vector solitons (GVLVSs) in Er-doped fiber laser have been investigated by using graphene oxide/polyvinyl alcohol (GO/PVA) film as a saturable absorber (SA). The generated Kelly sidebands in emission spectra reveal peak-valley or valley-peak alternation and slightly shift in two orthogonal components, which are the characteristics of GVLVSs. Through proper adjustment of polarization controllers (PCs) inside the EDFLs cavity, versatile vector soliton dynamics such as polarization locked GVLVSs (PL-GVLVSs), polarization rotation GVLVSs (PR-GVLVSs), dual wavelength GVLVSs, bound state GVLVSs, bunch GVLVSs and harmonic mode-locking GVLVSs (HML-GVLVSs) have been observed. The separation between two emission peaks from the dual wavelength GVLVSs was controlled by the Lyot filter and related to the insertion length of PMF inside the cavity. Unlike PL-GVLVSs, the period-doubling phenomenon has been found in two orthogonal components of the PR-GVLVSs. Besides, the bound state GVLVSs were generated showing strongly modulated interference fringes in emission spectrum. For the bunch and HML GVLVSs, the number of solitons inside the cavity increased with the pump power, and it showed the quintuple solitons and the 7th HML-GVLVSs at the highest pump power.

We propose and experimentally demonstrate a novel strategy to achieve dual-band symmetry-protected bound states in the continuum (BICs) in silicon metasurfaces. This strategy is based on the hybridization of Mie surface lattice resonances (SLRs) in periodic silicon bipartite nanodisk arrays, of which the central nanodisk displaced from the center of the unit cell. We show that dual-band electric quadrupole and magnetic dipole BICs can be supported in such a system, and transfer to quasi-BICs with ultrahigh measured quality factors up to 1240 at the Γ point. Taking advantage of the SLR characteristics, we show that the spectral separation and the quality factors of these two quasi-BICs can be conveniently tuned by varying the nanodisk diameter or the lattice period. Making use of these dual-band quasi-BICs, we numerically obtain bulk sensitivities above 480 nm/RIU and high figures of merit up to 1200. We also show that when the central nanodisk is not displaced but has different diameter, the silicon bipartite nanodisk array supports an electric dipole BIC that was referred to as subradiant SLR in the literature. Our work provides a new approach for realizing and tuning dual-band BICs, and the obtained ultrahigh- Q quasi-BICs can find potential applications in nonlinear optics, multimodal lasing, and optical sensing.

Structural colors with tunable properties have extensive applications in surface decoration, arts, absorbers, and optical filters. Planar structures have more advantages over other forms studied to date due to their easy manufacturability. Metal-insulator-metal-based structures are one of the known methods to fabricate structural colors where colors can be tuned mainly by the thickness of the intermediate lossless insulator layer. However, generating colors by MIM structure requires a thin metallic layer on top, and the top metals’ abrasiveness and/or oxidation may degrade the colors quickly. Thus, we propose a lossy dielectric layer to replace the top metallic layer as a solution to ensure the structure’s durability by preventing scratches and oxidation. Herein, CrON/Si 3 N 4 /Metal structures have been studied where theoretical investigations suggest that highly saturated colors can be generated in the lossy-lossless dielectric structures. Experimental data validated such simulations by revealing a range of vivid colors. Furthermore, these structures can easily achieve strong light absorption (SLA) even for a thick top layer of ∼100 nm. The colors realized by these structures are appeared due to a combination of the interference effect of the asymmetric Fabry–Perot cavity structure and the absorption rate in the CrO x N 1− x layer.

Silicon-based optical switch is one of the key components for on-chip optical interconnect systems, and mode division multiplexing technology has been employed to boost optical switches’ channel capacity. However, the majority of the proven multimode optical switches have a switching time in the microsecond range, which is insufficient for some applications. In this paper, we design and experimentally demonstrate a high-speed dual-mode 4 × 4 optical switch based on a mode-diversity scheme, composed of four pairs of mode multiplexers and de-multiplexers, and two optimized single-mode 4 × 4 optical switches. Fast switching is enabled based on the carrier dispersion effect. At the same time, we improve the performances of the optical switch by reducing the number of optical switch units used in the 4 × 4 Spanke–Beneš architecture. Its power consumptions are reduced by ∼17%. Its insertion losses are within 8.8 dB in the wavelength range of 1525–1565 nm in the both sates of “through” and “all-cross”, while the optical signal-to-noise ratios are larger than 12.8 dB. Also, 50 Gbps data transmission experiments verify the device’s data transmission functionality.

Optical Tamm states (OTS) are confined optical modes that can occur at the interface between two highly reflective structures. However, due to the strong reflectance required, their implementation with highly processable and metal-free flexible materials has proven challenging. Herein, we develop the first structure supporting OTS based only on organic polymeric materials, demonstrating a photonic platform based on non-critical, widely available and easily processable materials. The structures fabricated present large areas and consist of a narrowband multi-layered polymeric distributed Bragg reflector (DBR) followed by a thin film of J-aggregate molecular excitonic material that can act as a highly reflective surface within a narrowband range. We take advantage of the narrowband spectral response of the DBR and of the reflective molecular layer to tune the OTS band by varying the periodicity of the multilayer, opening the door for the fabrication of OTS structures based on lightweight integrable excitonic devices with cost-effective procedures.

The monitoring and conversion of photonic orbital angular momentum (OAM) play fundamental and important roles for both classic and quantum technologies, especially in low-loss transmission media such as ring-core fibers (RCFs), which make many OAM applications practical or vastly more flexible. However, in a RCF, the modes associated with different OAM states are highly overlapping due to the circular refractive index distribution structure, which makes it difficult to distinguish and monitor the OAM modes and in turn limits its inline conversion. Here, we report the first experimental realization of mode monitoring in a RCF using mode filters (MFs), which takes advantage of the difference in the mode adiabatic evolution and the higher-order mode cutoff conditions in tapered RCFs. Different-order OAM can be filtered using MFs with different geometric parameters, as demonstrated by the linearly polarized mode intensity. Combined the mode manipulations in RCF and single-mode fiber, the fundamental mode coupling efficiency can reach 90%, the RCF mode conversion monitoring through inline transmission spectrum evolution can be realized, and the inline fabrication of RCF grating, which couples one mode to a desired mode, can be demonstrated by the fabricating process of three long-period fiber gratings. The mode conversion efficiency between 0-order and 1, 2- or 3-order OAM modes exceeds 96%. Our work provides an efficient approach to monitor and convert OAM modes in higher-order mode supporting RCFs and even other special fibers and further promotes the improvement of the capacity of OAM transmission in RCFs.

As an exceptional nonlinear material, graphene offers versatile appealing properties, such as electro-optic tunability and high electromagnetic field confinement in the terahertz regime, spurring advance in ultrashort pulse formation, photodetectors and plasmonic emission. However, limited by atomic thickness, weak light–matter interaction still limits the development of integrated optical devices based on graphene. Here, an exquisitely designed meta-cavities combined with patterned graphene is used to overcome this challenge and promote THz-graphene interaction via terahertz location oscillation. By using an 800 nm pump laser, the local field-induced strong interaction allows sensitive responses to the ultrafast energy transfer from the ultrafast optical pump to graphene electron heat, enabling 46.2% enhancement of terahertz transparency. Such optical modulation of terahertz waves shows ultrafast response in delay less than 10 ps. Moreover, thanks to the nature of graphene, the device shows unique potential for electrically dynamic tuning and further bandwidth broadening.

We propose the realization of exceptional points (EP) at bound states in the continuum (BIC), with two coupled strips, made of an electron-beam resist and patterned on the thin film photonic integrated platform, which makes possible etchless photonics integrated circuits (PIC). The loss rate of the EP can be significantly decreased through merging the BIC peaks in the dual-BIC scheme. The orthogonality of the eigenvectors is retrieved for evaluating the Hermitian orthogonal eigenvectors and the non-Hermitian EP features. We also find that engineering the dimension of the dual-BIC scheme enables a transition between the coalesced eigenvectors in the EP and the orthogonal eigenvectors in the Hermitian system. This work is of great significance for the exploration on BIC-based directional coupling with ultralow-loss phase matching conditions, special coupling conditions of EPs and BICs with coupled quasi-BIC systems, dynamical EP encircling, and EP topology, in PICs.

The nitrogen-vacancy (NV) center in diamond is very sensitive to magnetic and electric fields, strain, and temperature. In addition, it is possible to optically interrogate individual defects, making it an ideal quantum-limited sensor with nanoscale resolution. A key limitation for the application of NV sensing is the optical brightness and collection efficiency of these defects. Plasmonic resonances of metal nanoparticles have been used in a variety of applications to increase the brightness and efficiency of quantum emitters, and therefore are a promising tool to improve NV sensing. However, the interaction between NV centers and plasmonic structures is largely unexplored. In particular, the back-action between NV and plasmonic nanoparticles is nonlinear and depends on optical wavelength, nanoparticle position, and metal type. Here we present the general theory of NV-plasmonic nanoparticle interactions. We detail how the interplay between NV response, including optical and vibrational signatures, and the plasmonic response of the metal nanoparticle results in modifications to the emission spectra. Our model is able to explain quantitatively the existing experimental measurements of NV centers near metal nanoparticles. In addition, it provides a pathway to developing new plasmonic structures to improve readout efficiencies in a range of applications for the NV center. This will enable higher precision sensors, with greater bandwidth as well as new readout modalities for quantum computing and communication.

Here, we investigate the nonreciprocal propagation and amplification of surface plasmons in drift-current biased graphene, using both Galilean and relativistic-type Doppler shift transformations of the graphene’s conductivity. Consistent with previous studies, both conductivity models predict strongly nonreciprocal propagation of surface plasmons due to the drag effect caused by the drifting electrons. In particular, the Galilean Doppler shift model leads to stronger spectral asymmetries in the plasmon dispersion with regimes of unidirectional propagation. Remarkably, it is shown that both conductivity models predict regimes of nonreciprocal plasmon amplification in a wide angular sector of in-plane directions when the drift-current biased graphene sheet is coupled to a plasmonic substrate (namely, SiC), with the plasmon amplification rate being substantially higher for the relativistic Doppler shift model.

Ferromagnetic semiconductor chromium sulfide (Cr 2 S 3 ), as a member of transition metal chalcogenide (TMC), exhibits the narrow bandgap value of 0.45 eV theoretically and has been applied in photoelectric field. However, the application in ultrafast fiber laser of Cr 2 S 3 has not been investigation at present. In this work, the Cr 2 S 3 -based SA was successfully prepared by depositing nanosheets onto tapered fiber. The conventional soliton (CS) operation, three pulse bound-state (BS) soliton operation, and noise-like pulse (NLP) operation around 1531 nm are observed from 80 mW to 147 mW in an EDFL. The experimental results demonstrated that Cr 2 S 3 as a promising 2D material has tremendous potential in designing ultrafast photonics device.