Home Effect of Flow Induced Orientation of Carbon Nanotubes on the Capillary Extrusion Behavior of Low-Density Polyethylene
Article Open Access

Effect of Flow Induced Orientation of Carbon Nanotubes on the Capillary Extrusion Behavior of Low-Density Polyethylene

  • H. Uematsu , T. Natsuume , S. Tanoue and Y. Iemoto
Published/Copyright: February 20, 2017
Download Article (PDF)
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Polymer Processing
From the journal International Polymer Processing Volume 32 Issue 1

Received: 2014-12-26
Accepted: 2016-06-09
Published Online: 2017-02-20
Published in Print: 2017-03-03

© 2017, Carl Hanser Verlag, Munich

Articles in the same Issue

  1. Contents
  2. Contents
  3. Editorial
  4. New Associate Editor for the Americas
  5. Regular Contributed Articles
  6. Effect of Flow Induced Orientation of Carbon Nanotubes on the Capillary Extrusion Behavior of Low-Density Polyethylene
  7. Mullins Effect under Compression Mode and its Reversibility of Thermoplastic Vulcanizate Based on Ethylene-Vinyl Acetate Copolymer/Styrene-Butadiene Rubber Blend
  8. Bio-Based Hybrid Polymers from Vinyl Ester Resin and Modified Palm Oil: Synthesis and Characterization
  9. Study on Crystal Form Transition and Non-Isothermal Crystallization of Glycidyl Methacrylate Grafted Isotactic Polybutene-1
  10. Flashing Method for Fabricating Micro Scale Fibers, Spheres, Porous and Condensed Polymer Structures
  11. Preparation and Performance Evaluation of SPEEK/Polyaniline Composite Membrane for Direct Methanol Fuel Cell
  12. Rotational Molding of Linear Low Density Polyethylene (LLDPE) Fumed Silica Nanocomposites
  13. Design Guidelines to Balance the Flow Distribution in Complex Profile Extrusion Dies
  14. Microstructure and Mechanical Properties of Nanocomposite Based on Polypropylene/Ethylene Propylene Diene Monomer/Graphene
  15. An Engineering Model that Simulates Pantographing Occurring in the Shaping Process of Reinforced Uncured Rubber Parts
  16. The Influence of Different Melt Temperatures on the Mechanical Properties of Injection Molded PA-12 and the Post Process Detection by Thermal Analysis
  17. Morphology and Thermal Behavior of TPU/PP Blends Modified with Maleic Anhydride Grafted SEBS-g-MA Block Copolymer
  18. Extrusion Blow Molding of Polymeric Blends Based on Thermotropic Liquid Crystalline Polymer and High Density Polyethylene
  19. Characterization of Stereocomplex Polylactide/Nanoclay Nanocomposites
  20. Attempts to Optimize the Dispersion State during Twin-Screw Extrusion of Polypropylene/Clay Nanocomposites
  21. Rapid Communications
  22. Improved Layer Mechanical Properties of Micro Injection Molded PP
  23. PPS News
  24. PPS News
  25. Seikei Kakou Abstracts
  26. Seikei-Kakou Abstracts
https://doi.org/10.3139/217.3062
Creative Commons
BY 4.0

Articles in the same Issue

  1. Contents
  2. Contents
  3. Editorial
  4. New Associate Editor for the Americas
  5. Regular Contributed Articles
  6. Effect of Flow Induced Orientation of Carbon Nanotubes on the Capillary Extrusion Behavior of Low-Density Polyethylene
  7. Mullins Effect under Compression Mode and its Reversibility of Thermoplastic Vulcanizate Based on Ethylene-Vinyl Acetate Copolymer/Styrene-Butadiene Rubber Blend
  8. Bio-Based Hybrid Polymers from Vinyl Ester Resin and Modified Palm Oil: Synthesis and Characterization
  9. Study on Crystal Form Transition and Non-Isothermal Crystallization of Glycidyl Methacrylate Grafted Isotactic Polybutene-1
  10. Flashing Method for Fabricating Micro Scale Fibers, Spheres, Porous and Condensed Polymer Structures
  11. Preparation and Performance Evaluation of SPEEK/Polyaniline Composite Membrane for Direct Methanol Fuel Cell
  12. Rotational Molding of Linear Low Density Polyethylene (LLDPE) Fumed Silica Nanocomposites
  13. Design Guidelines to Balance the Flow Distribution in Complex Profile Extrusion Dies
  14. Microstructure and Mechanical Properties of Nanocomposite Based on Polypropylene/Ethylene Propylene Diene Monomer/Graphene
  15. An Engineering Model that Simulates Pantographing Occurring in the Shaping Process of Reinforced Uncured Rubber Parts
  16. The Influence of Different Melt Temperatures on the Mechanical Properties of Injection Molded PA-12 and the Post Process Detection by Thermal Analysis
  17. Morphology and Thermal Behavior of TPU/PP Blends Modified with Maleic Anhydride Grafted SEBS-g-MA Block Copolymer
  18. Extrusion Blow Molding of Polymeric Blends Based on Thermotropic Liquid Crystalline Polymer and High Density Polyethylene
  19. Characterization of Stereocomplex Polylactide/Nanoclay Nanocomposites
  20. Attempts to Optimize the Dispersion State during Twin-Screw Extrusion of Polypropylene/Clay Nanocomposites
  21. Rapid Communications
  22. Improved Layer Mechanical Properties of Micro Injection Molded PP
  23. PPS News
  24. PPS News
  25. Seikei Kakou Abstracts
  26. Seikei-Kakou Abstracts
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 23.9.2025 from https://www.degruyterbrill.com/document/doi/10.3139/217.3062/html
Scroll to top button