Effect of Material Species on Flash Generation of PPS/GF Composites
-
Abstract
Reduction of flash in injection molding is of great concern for manufacturers of electrical parts. In a previous report we have proposed a theoretical model for flash generation. The present study prepares five different poly(phenylene sulfide)/glass fiber composites using three different PPS; linear, branched and crosslinked PPS and measures the length of flash generated in the molding of the composites. Then, we have compared the flash data with a flash parameter defined in the model. This comparison has elucidated that flash length can be related with the flash parameter irrespective of PPS structure, as long as GF content is the same and the clearance of a gas vent is almost identical.
References
1 Kawahara, Y.: Kogyo Zairyo36(6), p. 45 (1988).Search in Google Scholar
2 Izutsu, H.: Kogyo Zairyo41(9), p. 35 (1993).Search in Google Scholar
3 Suenaga, J., Koromogawa, M., Marutani, T., Ohnishi, Y.: Proc. of Polym. Mater. Forum1, p. 73 (1994).Search in Google Scholar
4 Kobayashi, K.: Kogyo Zairyo42(6), p. 68 (1994).Search in Google Scholar
5 Chiba, K.: Kogyo Zairyo42(11), p. 37 (1994).Search in Google Scholar
6 Nakamura, S.: Plastic Seikeigijutsu11(11), p. 22 (1994).Search in Google Scholar
7 Greer, M. R.: Proc. of 2nd Conf. Plast. Portable Wirel. Electron., p. 75 (1996).Search in Google Scholar
8 Mori, Y.: Plastics48(1), p. 99 (1997).10.1016/S0303-8467(97)82271-8Search in Google Scholar
9 Negishi, H.: DIC Tech. Rev.3, p. 112 (1997).Search in Google Scholar
10 Suzuki, K., Ishii, T.: Plastics49(1), p. 84 (1998).Search in Google Scholar
11 Komiyama, O.: JETI46(8), p. 71 (1998).Search in Google Scholar
12 Kawabata, T.: DIC Tech. Rev.6, p. 76 (2000).Search in Google Scholar
13 Takano, T.: Plastics52(7), p. 55 (2001).10.1136/jech.55.10.748Search in Google Scholar PubMed PubMed Central
14 Ueda, U.: Plastics Seikeigijutsu11(7), p. 87 (1994).10.1016/B978-1-4832-8380-7.50027-4Search in Google Scholar
15 Higuchi, H., Kosaka, W., Koyama, K.: Poly. Eng. & Sci.45(2), p. 198 (2005).10.1002/pen.20266Search in Google Scholar
16 Higuchi, H., Goto, H., Koyama, K.: Poly. Eng. & Sci.45(2), p. 238 (2005).10.1002/pen.20270Search in Google Scholar
© 2005, Carl Hanser Verlag, Munich
Articles in the same Issue
- Contents
- Contents
- Editorial
- International Polymer Processing Special Issue Macro 2004
- Invited Paper
- A Dilatometer to Measure the Influence of Cooling Rate and Melt Shearing on Specific Volume
- Monitoring Reactive Processes along the Extruder
- Stretch and Shape Distributions of Droplets with Interfacial Tension in Chaotic Mixing
- Cast Film Extrusion
- Nozzle Injection of Physical Blowing Agents in the Injection Molding of Microcellular Foams
- Visualization Analysis of Asymmetric Fountain Flow Phenomenon in Injection Molding of Filler-reinforced Resins by Rotary Runner Exchange System
- In-process Monitoring of Micromoulding – Assessment of Process Variation
- Processing-induced Properties in Glassy Polymers
- Structure Development in Injection Molding: A 3D Simulation with a Differential Formulation of the Kinetic Equations
- Evolution of Morphology of iPP in Processing Conditions
- Regular Contributed Articles
- 3D Simulation of Gas Assisted Injection Molding Analysis of Primary and Secondary Gas Penetration and Comparison with Experimental Results
- Microcellular Injection Molding
- Effect of Material Species on Flash Generation of PPS/GF Composites
- PPS News
- PPS News
- Seikei-Kakou Abstracts
- Seikei-Kakou Abstracts
Articles in the same Issue
- Contents
- Contents
- Editorial
- International Polymer Processing Special Issue Macro 2004
- Invited Paper
- A Dilatometer to Measure the Influence of Cooling Rate and Melt Shearing on Specific Volume
- Monitoring Reactive Processes along the Extruder
- Stretch and Shape Distributions of Droplets with Interfacial Tension in Chaotic Mixing
- Cast Film Extrusion
- Nozzle Injection of Physical Blowing Agents in the Injection Molding of Microcellular Foams
- Visualization Analysis of Asymmetric Fountain Flow Phenomenon in Injection Molding of Filler-reinforced Resins by Rotary Runner Exchange System
- In-process Monitoring of Micromoulding – Assessment of Process Variation
- Processing-induced Properties in Glassy Polymers
- Structure Development in Injection Molding: A 3D Simulation with a Differential Formulation of the Kinetic Equations
- Evolution of Morphology of iPP in Processing Conditions
- Regular Contributed Articles
- 3D Simulation of Gas Assisted Injection Molding Analysis of Primary and Secondary Gas Penetration and Comparison with Experimental Results
- Microcellular Injection Molding
- Effect of Material Species on Flash Generation of PPS/GF Composites
- PPS News
- PPS News
- Seikei-Kakou Abstracts
- Seikei-Kakou Abstracts
