Startseite Structural and magnetic evolution of ball milled nanocrystalline Fe-50 at.% Al alloy
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Structural and magnetic evolution of ball milled nanocrystalline Fe-50 at.% Al alloy

  • Sandeep Rajan , Rajni Shukla , Anil Kumar , Anupam Vyas und Ranjeet Brajpuriya EMAIL logo
Veröffentlicht/Copyright: 27. Oktober 2021
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 106 Heft 2

Abstract

Investigations regarding structural, morphological, and magnetic changes induced by ball milling of Fe-50 at.% Al alloy have been carried out. The mechanical alloying process induces a progressive dissolution of Al into Fe, resulting in the nucleation and establishment of an elongated nanostructured Fe(Al) solid solution with the bcc structure only after 5 hr of milling. The average crystallite size of components decreased to ~5 nm and the components diffused to the nanograin boundaries during transition to nanostructured composite. Scanning electron microscopy and transmission electron microscopy confirmed the crystallite size determination and Fe(Al) solid solution formation obtained from X-ray diffraction analysis. The corresponding magnetic (Mössbauer and vibration sample magnetometer) studies confirm that there is magnetic behaviour retained in the FeAl alloys samples even after 5 hr of milling but magnetization decreases as the milling time increases. The ball milling process involves the loss of long range order and reduced grain size, which induces a transition from a paramagnetic to ferromagnetic state. The continuous refinement of grains and the antiphase interface grain bounderies play a major part in the observed variation in the magnetic properties.

Keywords: Transition metal aluminides; Mechanical alloying; Phase formation
Dr. Ranjeet Brajpuriya Assistant Professor Department of Physics, Amity University Haryana Manesar Gurgoan, 122413 India Tel.: +91 8527769007

References

[1] A. Hernando, J.M. Gonzalez: Hyperfine Interact. 130 (2000) 221. DOI:10.1023/A:101109652242910.1023/A:1011096522429Suche in Google Scholar

[2] R. Viswanathan, J.F. Henry, J. Tanzosh, G. Stanko, J.P. Shingledecker, B. Vitalis, U.S. Program on materials technology for ultra supercritical stream coal-fired power plants, Materials for Advanced Power Engineering, Energy Technology 53 (2006) 893.Suche in Google Scholar

[3] M. Muller: Energy Materials: Materials Science and Engineering for Energy Systems 1(4) (2006) 223. DOI:10.1179/174892406X17360210.1179/174892406X173602Suche in Google Scholar

[4] R. Darolia, J.J. Lewandowski, C.T. Liu, P.L. Martin, D.B. Miracle, M.V. Nathal (Eds.): Structural intermetallics, The Minerals, Metals and Materials Society: Warrendale, PA (1993) 127.Suche in Google Scholar

[5] C.G. McKamey, J.H. Devan, P.F. Tortorelli, V.K. Sikka: J. Mater. Res. 6 (1991) 695. DOI:10.1557/JMR.1991.177910.1557/JMR.1991.1779Suche in Google Scholar

[6] N.S. Stoloff, R.C. Davies: Prog. Mater. Sci. 13 (1966) 1. DOI:10.1016/0079-6425(68)90018-210.1016/0079-6425(68)90018-2Suche in Google Scholar

[7] S.C. Deevi, V.K. Sikka: Intermetallics 4 (1996) 357. DOI:10.1016/0966-9795(95)00056-910.1016/0966-9795(95)00056-9Suche in Google Scholar

[8] J.S. Kouvel, in: J.H. Westbrook, R.L. Fleischer (Eds.), Intermetallic Compounds: Principles, Wiley, New York 1 (1994) 935.Suche in Google Scholar

[9] U.R. Kattner, in: T.B. Massalski (Ed.), Binary Alloy Phase Diagrams, ASM International, Metals Park, OH (1990) 147.Suche in Google Scholar

[10] V. Reddy, P. Jenna, S.C. Deevi: Intermetallics 8 (2000) 1197. DOI:10.1016/S0966-9795(00)00075-310.1016/S0966-9795(00)00075-3Suche in Google Scholar

[11] C. Lilly, S.C. Deevi, Z.P. Gibbs: Mater. Sci. Eng. 42 (1998) A 258.10.1016/S0921-5093(98)00915-0Suche in Google Scholar

[12] E.P. George, M. Yamaguchi, K.S. Kumar, C.T. Liu: Ann. Rev. Mater. Sci. 25 (1994) 409. DOI:10.1146/annurev.ms.24.080194.00220510.1146/annurev.ms.24.080194.002205Suche in Google Scholar

[13] S.C. Deevi: Intermetallics 8 (2000) 679. DOI:10.1016/S0966-9795(99)00129-610.1016/S0966-9795(99)00129-6Suche in Google Scholar

[14] O. Pocci, O. Tassa, C. Testani, in: Processing, Properties and Application of Iron Aluminides, The Materials, Metals and Minerals Society, PA (1994) 19.Suche in Google Scholar

[15] N. Srinivasa, VK. Sikka, in: Processing, Properties and Application of Iron Aluminides, The Materials, Metals and Minerals Society, PA (1994) 69.Suche in Google Scholar

[16] H. Gleiter: Prog. Mater. Sci. 33 (1991) 223. DOI:10.1016/0079-6425(89)90001-710.1016/0079-6425(89)90001-7Suche in Google Scholar

[17] C.C. Koch: Mater. Sci. Forum 88 (1992) 243.10.4028/www.scientific.net/MSF.88-90.243Suche in Google Scholar

[18] R. Bohn, T. Haubold, R. Birringer, H. Gleiter: Scr. Metall. Mater. 25 (1991) 811. DOI:10.1016/0956-716X(91)90230-X10.1016/0956-716X(91)90230-XSuche in Google Scholar

[19] C. Suryanarayana: Prog. Mater. Sci. 46 (2001) 1. DOI:10.1016/S0079-6425(99)00010-910.1016/S0079-6425(99)00010-9Suche in Google Scholar

[20] X. Amils, J. Nogués, S. Suriñach, J.S. Muñoz, M.D. Baró, A. Hernando, J.P. Morniroli: Phys. Rev. B 63 (2001) 052402. DOI:10.1103/PhysRevB.63.05240210.1103/PhysRevB.63.052402Suche in Google Scholar

[21] L.F. Kiss, D. Kaptás, J. Balogh, L. Bujdosó, T. Kemény, L. Vincze, J. Gubicza: Phys. Rev. B 70 (2004) 012408. DOI:10.1103/PhysRevB.70.01240810.1103/PhysRevB.70.012408Suche in Google Scholar

[22] S. Gialanella, X. Amils, M.D. Barò, P. Delcroix, G. Le Caër, L. Lutterotti, S. Suriñach: Acta Mater. 46 (1998) 3305. DOI:10.1016/S1359-6454(97)00484-910.1016/S1359-6454(97)00484-9Suche in Google Scholar

[23] S. Gialanella: Intermetallics 3 (1995) 73. DOI:10.1016/0966-9795(94)P3680-M10.1016/0966-9795(94)P3680-MSuche in Google Scholar

[24] G.K. Rane, U. Welzel, S.R. Meka, E.J. Mittemeijer: Acta Mater. 61 (2013) 4524. DOI:10.1016/j.actamat.2013.04.02110.1016/j.actamat.2013.04.021Suche in Google Scholar

[25] J. Nogués, E. Apiñaniz, J. Sort, M. Amboage, M. d’Astuto, O. Mathon, R. Puzniak, I. Fita, J.S. Garitaonandia, S. Suriñach, J.S. Muñoz, M.D. Baró, F. Plazaola, F. Baudelet: Phys. Rev. B 74 (2006) 024407. DOI:10.1103/PhysRevB.74.02440710.1103/PhysRevB.74.024407Suche in Google Scholar

[26] C. Mangler, C. Gammer, K. Hiebl, H.P. Karnthaler, C. Rentenberger: J. Alloys Compd. 509S (2011) S389-S392. DOI:10.1016/j.jallcom.2010.12.02310.1016/j.jallcom.2010.12.023Suche in Google Scholar

[27] S. Takahashi, Y. Umakoshi: J. Phys. Condens. Matter 2 (1990) 4007. DOI:10.1088/0953-8984/2/17/01210.1088/0953-8984/2/17/012Suche in Google Scholar

[28] Y. Yang, I. Baker, P. Martin: Philos. Mag. B 79 (1999) 449. DOI:10.1080/0141861990821030910.1080/01418619908210309Suche in Google Scholar

[29] O. Kubaschewski: Iron-Binary Phase Diagrams, Spinger-Verlag, Berlin (1982) 5.Suche in Google Scholar

[30] R. Koohkan, S. Sharafi, H. Shokrollahi, K. Janghorban: J. Magn. Magn. Mater. 320(6) (2008) 1089. DOI:10.1016/j.jmmm.2007.10.03310.1016/j.jmmm.2007.10.033Suche in Google Scholar

[31] E. Jartych, J.K. Zurawicz, D. Oleszak, M. Pekala: Nanostruct. Mater. 12 (1999) 927. DOI:10.1016/S0965-9773(99)00269-X10.1016/S0965-9773(99)00269-XSuche in Google Scholar

[32] W.M. Tang, Z.X. Zheng, H.J. Tang, R. Ren, Y.C. Wu: Intermetallics 15(8) (2007) 1020. DOI:10.1016/j.intermet.2006.12.00510.1016/j.intermet.2006.12.005Suche in Google Scholar

[33] R.A. Dunlap, J.R. Dahn, D.A. Eleman, G.R. Mackey: Hyperfine Interact. 116 (1998) 117. DOI:10.1023/A:101268571397010.1023/A:1012685713970Suche in Google Scholar

[34] M. Krasnowski, A. Grabias, T. Kulik: J. Alloys Compd. 424 (2006) 119–127. DOI:10.1016/j.jallcom.2005.12.07710.1016/j.jallcom.2005.12.077Suche in Google Scholar

[35] R.A. Dunlap, D.A. Small, G.R. Mackey, J.W. O’Brien, J.R. Dahn, Z.H. Cheng: Can. J. Phys. 78(3) (2000) 211–229. DOI:10.1139/p99-06710.1139/p99-067Suche in Google Scholar

[36] A.E. Berkowitz, K. Takano: J. Magn. Magn. Mater. 200 (1999) 552. DOI:10.1016/S0304-8853(99)00453-910.1016/S0304-8853(99)00453-9Suche in Google Scholar

[37] G. Herzer, in: K.H.J. Buschow (Ed.), Handbook of Magnetic Materials, Elsevier Science B.V., 10 (1997) 415–462.Suche in Google Scholar

[38] M.J. Besnus, A. Herr, A.J.P. Meyer: J. Phys. F 5 (1975) 2138. DOI:10.1088/0305-4608/5/11/02610.1088/0305-4608/5/11/026Suche in Google Scholar

[39] V. Sundararajan, B.R. Sahu, D.G. Kanhere, P.V. Panat, G.P. Das: J. Phys. Condens. Matter 7 (1995) 6019. DOI:10.1088/0953-8984/7/30/00710.1088/0953-8984/7/30/007Suche in Google Scholar

[40] X. Amils, J. Nogues, S. Surinach, M.D. Baro, J.S. Munoz: IEEE Trans. Magn. 34 (1998) 1129. DOI:10.1109/20.70640910.1109/20.706409Suche in Google Scholar

[41] A. Hernando, X. Amils, J. Nogues, S. Surinach, M.D. Baro, M.R. Ibarra: Phys. Rev. B 58 (1998) R11864. DOI:10.1103/PhysRevB.58.36610.1103/PhysRevB.58.366Suche in Google Scholar

[42] Q. Zeng, I. Baker: Intermetallics 14 (2006) 396. DOI:10.1016/j.intermet.2005.07.00510.1016/j.intermet.2005.07.005Suche in Google Scholar

[43] X. Amils, J.S. Garitaonandia, J. Nogues, S. Surinach, F. Plazaola, J.S. Munoz, M.D. Baro: J. Non-Cryst. Solids 287 (2001) 272–276. DOI:10.1016/S0022-3093(01)00586-510.1016/S0022-3093(01)00586-5Suche in Google Scholar

[44] K. Raviprasad, K. Chattopadhyay: Philos. Mag. Lett. 65 (1992) 255–259. DOI:10.1080/0950083920820754410.1080/09500839208207544Suche in Google Scholar

[45] P.A. Beck: Metall. Trans. 2 (1971) 2015–2024. DOI:10.1007/BF0266275010.1007/BF02662750Suche in Google Scholar

Received: 2014-04-07
Accepted: 2014-10-08
Published Online: 2021-10-27

© 2015 Carl Hanser Verlag GmbH & Co. KG

Artikel in diesem Heft

  1. Frontmatter
  2. Original Contributions
  3. Microstructures of magnetron sputtered Fe–Au thin films
  4. Phase-field simulation of diffusion-controlled coarsening kinetics of γ’ phase in Ni–Al alloy
  5. Structural and magnetic evolution of ball milled nanocrystalline Fe-50 at.% Al alloy
  6. Structural, optical and magnetic properties of nanocrystalline zinc ferrite particles from glycine assisted combustion: Effect of Sr2+ dopant
  7. Correlation of plastic deformation induced intermittent electromagnetic radiation characteristics with mechanical properties of Cu–Ni alloys
  8. Effect of isothermal quenching methods on impact toughness and wear resistance in high boron steel
  9. Wear behaviour of Al/(Al2O3 + ZrB2 + TiB2) hybrid composites fabricated by hot pressing
  10. Regression analysis of bonding strength of sprayed coatings based on acoustic emission signal
  11. Effect of substrates on covalent surface modification of graphene using photosensitive functional group
  12. Short Communications
  13. Investigation of optimum nucleation temperature and heating rate of cordierite glass-ceramics
  14. The influence of process parameters on the preparation of CaF2@Al(OH)3 composite powder via heterogeneous nucleation
  15. Effect of zirconium and heat treatment on the microstructure and properties of cast chromium bronze for conductive parts
  16. The influence of addition of citric acid on the physical properties of metallic oxide nanorods via Sol-Gel route preparation
  17. Notifications
  18. People
  19. DGM News
  20. Conferences
https://doi.org/10.3139/146.111162
Schlagwörter für diesen Artikel
Transition metal aluminides; Mechanical alloying; Phase formation

Artikel in diesem Heft

  1. Frontmatter
  2. Original Contributions
  3. Microstructures of magnetron sputtered Fe–Au thin films
  4. Phase-field simulation of diffusion-controlled coarsening kinetics of γ’ phase in Ni–Al alloy
  5. Structural and magnetic evolution of ball milled nanocrystalline Fe-50 at.% Al alloy
  6. Structural, optical and magnetic properties of nanocrystalline zinc ferrite particles from glycine assisted combustion: Effect of Sr2+ dopant
  7. Correlation of plastic deformation induced intermittent electromagnetic radiation characteristics with mechanical properties of Cu–Ni alloys
  8. Effect of isothermal quenching methods on impact toughness and wear resistance in high boron steel
  9. Wear behaviour of Al/(Al2O3 + ZrB2 + TiB2) hybrid composites fabricated by hot pressing
  10. Regression analysis of bonding strength of sprayed coatings based on acoustic emission signal
  11. Effect of substrates on covalent surface modification of graphene using photosensitive functional group
  12. Short Communications
  13. Investigation of optimum nucleation temperature and heating rate of cordierite glass-ceramics
  14. The influence of process parameters on the preparation of CaF2@Al(OH)3 composite powder via heterogeneous nucleation
  15. Effect of zirconium and heat treatment on the microstructure and properties of cast chromium bronze for conductive parts
  16. The influence of addition of citric acid on the physical properties of metallic oxide nanorods via Sol-Gel route preparation
  17. Notifications
  18. People
  19. DGM News
  20. Conferences
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 28.10.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.111162/pdf?lang=de
Button zum nach oben scrollen