Startseite Prof. Dr. Tomaž Kosmač
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Prof. Dr. Tomaž Kosmač

  • Nils Claussen
Veröffentlicht/Copyright: 18. Oktober 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 104 Heft 10

Published Online: 2013-10-18
Published in Print: 2013-10-10

© 2013, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Martensite–austenite transformation kinetics of high Cr ferritic heat-resistant steel
  5. Ageing texture of hot rolled and solution treated Ti–Nb alloys
  6. Artificial aging of thixocast ZA27 alloy and particulate ZA27/SiCp composites
  7. Low cycle fatigue behavior under asymmetric loading of two AZ31B magnesium alloys with different microstructures and textures
  8. Mechanical properties of aluminum extruded via the KOBO method with direct and lateral outflow
  9. Hot compression deformation of an Mg–2.54Nd–0.26Zn–0.32Zr alloy
  10. Evaluation of the sliding performance of polyamide, poly-oxy-methylene and their composites
  11. Corrosion behaviour of AISI 204Cu and AISI 304 stainless steels in simulated pore solution
  12. Comparing the corrosion behavior of nanograined and coarse-grained interstitial free steels
  13. Electrochemical investigation of the effect of different laser surface treatments on Hastelloy G alloy
  14. Influence of sputtering gas pressure on properties of transparent conducting Si-doped zinc oxide films
  15. Cu2SnS3 absorber thin films prepared via successive ionic layer adsorption and reaction method
  16. Nano preparation of Dy3+ substituted ceria via urea-formaldehyde gel combustion route
  17. Short Communications
  18. Preparation of ZrB2-based nanocomposites with limited grain growth by means of low-temperature hot-pressing using Cu additive
  19. Combustion synthesis of Ti2SC
  20. People
  21. Prof. Dr. Tomaž Kosmač
  22. DGM News
  23. DGM News
https://doi.org/10.3139/146.013105

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Martensite–austenite transformation kinetics of high Cr ferritic heat-resistant steel
  5. Ageing texture of hot rolled and solution treated Ti–Nb alloys
  6. Artificial aging of thixocast ZA27 alloy and particulate ZA27/SiCp composites
  7. Low cycle fatigue behavior under asymmetric loading of two AZ31B magnesium alloys with different microstructures and textures
  8. Mechanical properties of aluminum extruded via the KOBO method with direct and lateral outflow
  9. Hot compression deformation of an Mg–2.54Nd–0.26Zn–0.32Zr alloy
  10. Evaluation of the sliding performance of polyamide, poly-oxy-methylene and their composites
  11. Corrosion behaviour of AISI 204Cu and AISI 304 stainless steels in simulated pore solution
  12. Comparing the corrosion behavior of nanograined and coarse-grained interstitial free steels
  13. Electrochemical investigation of the effect of different laser surface treatments on Hastelloy G alloy
  14. Influence of sputtering gas pressure on properties of transparent conducting Si-doped zinc oxide films
  15. Cu2SnS3 absorber thin films prepared via successive ionic layer adsorption and reaction method
  16. Nano preparation of Dy3+ substituted ceria via urea-formaldehyde gel combustion route
  17. Short Communications
  18. Preparation of ZrB2-based nanocomposites with limited grain growth by means of low-temperature hot-pressing using Cu additive
  19. Combustion synthesis of Ti2SC
  20. People
  21. Prof. Dr. Tomaž Kosmač
  22. DGM News
  23. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 16.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.013105/pdf
Button zum nach oben scrollen