Article
Licensed
Unlicensed Requires Authentication

Contents

Published/Copyright: October 18, 2013
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 104 Issue 10

Published Online: 2013-10-18
Published in Print: 2013-10-10

© 2013, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Martensite–austenite transformation kinetics of high Cr ferritic heat-resistant steel
  5. Ageing texture of hot rolled and solution treated Ti–Nb alloys
  6. Artificial aging of thixocast ZA27 alloy and particulate ZA27/SiCp composites
  7. Low cycle fatigue behavior under asymmetric loading of two AZ31B magnesium alloys with different microstructures and textures
  8. Mechanical properties of aluminum extruded via the KOBO method with direct and lateral outflow
  9. Hot compression deformation of an Mg–2.54Nd–0.26Zn–0.32Zr alloy
  10. Evaluation of the sliding performance of polyamide, poly-oxy-methylene and their composites
  11. Corrosion behaviour of AISI 204Cu and AISI 304 stainless steels in simulated pore solution
  12. Comparing the corrosion behavior of nanograined and coarse-grained interstitial free steels
  13. Electrochemical investigation of the effect of different laser surface treatments on Hastelloy G alloy
  14. Influence of sputtering gas pressure on properties of transparent conducting Si-doped zinc oxide films
  15. Cu2SnS3 absorber thin films prepared via successive ionic layer adsorption and reaction method
  16. Nano preparation of Dy3+ substituted ceria via urea-formaldehyde gel combustion route
  17. Short Communications
  18. Preparation of ZrB2-based nanocomposites with limited grain growth by means of low-temperature hot-pressing using Cu additive
  19. Combustion synthesis of Ti2SC
  20. People
  21. Prof. Dr. Tomaž Kosmač
  22. DGM News
  23. DGM News
https://doi.org/10.3139/146.013102

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Martensite–austenite transformation kinetics of high Cr ferritic heat-resistant steel
  5. Ageing texture of hot rolled and solution treated Ti–Nb alloys
  6. Artificial aging of thixocast ZA27 alloy and particulate ZA27/SiCp composites
  7. Low cycle fatigue behavior under asymmetric loading of two AZ31B magnesium alloys with different microstructures and textures
  8. Mechanical properties of aluminum extruded via the KOBO method with direct and lateral outflow
  9. Hot compression deformation of an Mg–2.54Nd–0.26Zn–0.32Zr alloy
  10. Evaluation of the sliding performance of polyamide, poly-oxy-methylene and their composites
  11. Corrosion behaviour of AISI 204Cu and AISI 304 stainless steels in simulated pore solution
  12. Comparing the corrosion behavior of nanograined and coarse-grained interstitial free steels
  13. Electrochemical investigation of the effect of different laser surface treatments on Hastelloy G alloy
  14. Influence of sputtering gas pressure on properties of transparent conducting Si-doped zinc oxide films
  15. Cu2SnS3 absorber thin films prepared via successive ionic layer adsorption and reaction method
  16. Nano preparation of Dy3+ substituted ceria via urea-formaldehyde gel combustion route
  17. Short Communications
  18. Preparation of ZrB2-based nanocomposites with limited grain growth by means of low-temperature hot-pressing using Cu additive
  19. Combustion synthesis of Ti2SC
  20. People
  21. Prof. Dr. Tomaž Kosmač
  22. DGM News
  23. DGM News
Downloaded on 14.4.2026 from https://www.degruyterbrill.com/document/doi/10.3139/146.013102/html
Scroll to top button