Home Technology Comparing the corrosion behavior of nanograined and coarse-grained interstitial free steels
Article
Licensed
Unlicensed Requires Authentication

Comparing the corrosion behavior of nanograined and coarse-grained interstitial free steels

  • Kamran Dehghani , Maryam Hosseini and Atiye Nekahi
Published/Copyright: October 18, 2013
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 104 Issue 10

Abstract

The corrosion behavior of nanograined (NG) IF-steel was compared with its coarse-grained (CG) counterpart. The corrosion tests were carried out using different solutions of NaCl and H2SO4. The results show that the nanostructured IF steel exhibited higher corrosion resistance (Ecorr) and lower corrosion rate (icorr). According to the corroded microstructures, extensive cracking was observed in the case of CG subjected to both chloride and acidic media, as well as localized corrosion with signs of severe pitting. The results also show that NaCl can act as an inhibitor when added to H2SO4-containg solution leading to a decrease in the detrimental effect of H2SO4.

Keywords:: Corrosion; Interstitial free steel; Wire brushing; Nanostructure; Severe plastic deformation
* Correspondence address, Kamran Dehghani, Amirkabir Uni. Tech., Dept. Mining Metall. Eng., Hafez Avenue, Tehran, Iran, Tel.: +9891 23261491, Fax: +9821 66405846, E-mail:

References

[1] R.Z.Valiev, R.K.Islamgaliev, I.V.Alexandrov: Prog. Mater. Sci.45 (2000) 103. 10.1016/S0079-6425(99)00007-9Search in Google Scholar

[2] X.Y.Zhang, M.H.Shi, C.Li, N.F.Liu, Y.M.Wei: Mat. Sci. Eng. A448 (2007) 259. 10.1016/j.msea.2006.10.012Search in Google Scholar

[3] T.Roland, D.Retraint, K.Lu, J.Lu: Mat. Sci. Eng. A445–446 (2007) 281. 10.1016/j.msea.2006.09.041Search in Google Scholar

[4] M.Sato, N.Tsuji, Y.Minamino, Y.Koizumi: Sci. Technol. Adv. Mat.5 (2004) 145. 10.1016/j.stam.2003.10.015Search in Google Scholar

[5] M.A.Meyers, A.Mishra, D.J.Benson: Prog. Mater. Sci.51 (2006) 427. 10.1016/j.pmatsci.2005.08.003Search in Google Scholar

[6] E.V.Nesterova, B.Bacroix, C.Teodosiu: Metall. Mater. Trans.A 32 A (2001) 2527.10.1007/s11661-001-0042-9Search in Google Scholar

[7] S.D.Lu, Z.B.Wang, K.Lu: Mat. Sci. Eng. A527 (2010) 995. 10.1016/j.msea.2009.10.030Search in Google Scholar

[8] B.Hadzima, M.Janecek, Y.Estrin, H.S.Kim: Mat. Sci. Eng.A 462 (2007) 243. 10.1016/j.msea.2005.11.081Search in Google Scholar

[9] X.Y.Mao, D.Y.Li, F.Fang, R.S.Tan, J.Q.Jiang: Mat. Sci. Eng.A 527 (2010) 2875. 10.1016/j.msea.2009.09.040Search in Google Scholar

[10] X.Y.Wang, D.Y.Li: Electrochim. Acta47 (2002) 3939. 10.1016/S0013-4686(02)00365-1Search in Google Scholar

[11] X.Y.Wang, D.Y.Li: Wear255 (2003) 836. 10.1016/S0043-1648(03)00055-3Search in Google Scholar

[12] H.B.Lu, YingLi, F.H.Wang: Thin Solid Films510 (2006) 197. 10.1016/j.tsf.2005.11.051Search in Google Scholar

[13] C.T.Kwok, F.T.Cheng, H.C.Man, W.H.Ding: Mater. Lett.60 (2006) 2419. 10.1016/j.matlet.2006.01.053Search in Google Scholar

[14] A.Balyanov, J.Kutnyakova, N.A.Amirkhanova, V.V.Stolyarov, R.Z.Valiev, X.Z.Liao, Y.H.Zhao, Y.B.Jiang, X.F.Xu, T.C.Lowe, Y.T.Zhu: Scripta Mater.51 (2004) 225. 10.1016/j.scriptamat.2004.04.011Search in Google Scholar

[15] H.Garbacz, M.Pisarek, K.J.Kurzydlowski: Biomol. Eng.24 (2007) 559. 10.1016/j.bioeng.2007.08.007Search in Google Scholar PubMed

[16] A.S.Hamada, L.P.Karjalainen, M.C.Somani: Mat. Sci. Eng.A 431 (2006) 211. 10.1016/j.msea.2006.05.138Search in Google Scholar

[17] A.Bahari, S.A.Babanezhad, F.Ashrafi, M.Moshahedi: World Appl. Sci. J.7 (2009) 22.Search in Google Scholar

[18] M. BobbyKannan, R.K. SinghRaman, S.Khoddam: Corros. Sci.50 (2008) 2879. 10.1016/j.corsci.2008.07.024Search in Google Scholar

[19] G.Davies: Materials for Automobile Bodies, Butterworth-Heinemann, Oxford (2003) 189. 10.1016/B978-075065692-4/50024-8Search in Google Scholar

[20] R.M.Hudson, C.J.Warning: Metal Finish.78 (6) (1980) 21.Search in Google Scholar

[21] A.Chabok, K.Dehghani: Mat. Sci. Eng. A528 (2010) 309. 10.1016/j.msea.2010.08.096Search in Google Scholar

[22] A.Yazdipour, A.Shafiei, M. K.Dehghani: Mat. Sci. Eng. A527 (2009) 192. 10.1016/j.msea.2009.08.040Search in Google Scholar

[23] Y. AitAlbrimi, A.Eddib, J.Douch, Y.Berghoute, M.Hamdani, R.M.Souto: Int. J. Electrochem. Sci.6 (2011) 4614.Search in Google Scholar

[24] A.A.Khedr, S.H.Sanad, K.M.El-Sobki: Surf. Tech.23 (2) (1984) 151. 10.1016/0376-4583(84)90121-3Search in Google Scholar

[25] S.E.Traubenberg, R.T.Foley: J. Electrochem. Soc.118 (7) (1971) 1066. 10.1149/1.2408248Search in Google Scholar

[26] B.Gaur, T.B.Singh, D.D.N.Singh: Corrosion52 (2) (1996) 96020154 (9 pages). 10.5006/1.3292106Search in Google Scholar

[27] T.Misawa, K.Hashimoto, W.Suetaka, and S.Shimodaira, in: Proc. 5th Int. Cong. Metallic Corrosion, Houston, Texas, USA (1972) 775.Search in Google Scholar

[28] Metals Handbook, vol. 13A, ASM Int., Materials Park, OH, USA, (2003).Search in Google Scholar

[29] T.P.Hoar: J. Electrochem. Soc.117 (1970) 17C.Search in Google Scholar

[30] M.P.Ryan, R.C.Newman, G.E.Thompson: Phil. Mag. B70 (1994) 241. 10.1080/01418639408241803Search in Google Scholar

[31] M.P.Ryan, S.Fugimoto, G.E.Thompson, R.C.Newman: Mater. Sci. Forum185–188 (1995) 233. 10.4028/www.scientific.net/MSF.185-188.233Search in Google Scholar

[32] G.G.Long, J.Kruger, M.Kuriyama, D.R.Black, E.Farabaugh, D.M.Saunders, A.I.Goldman, in: Proc. 9th Int. Cong. Metallic Corrosion, Vol. 3, National Research Council, Ottawa, Canada, (1984) 419–422.Search in Google Scholar

[33] A.G.Revesz, J.Kruger: Passivity of metals, Electrochemical Society, USA, (1978).Search in Google Scholar

Received: 2012-7-25
Accepted: 2013-5-8
Published Online: 2013-10-18
Published in Print: 2013-10-10

© 2013, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Martensite–austenite transformation kinetics of high Cr ferritic heat-resistant steel
  5. Ageing texture of hot rolled and solution treated Ti–Nb alloys
  6. Artificial aging of thixocast ZA27 alloy and particulate ZA27/SiCp composites
  7. Low cycle fatigue behavior under asymmetric loading of two AZ31B magnesium alloys with different microstructures and textures
  8. Mechanical properties of aluminum extruded via the KOBO method with direct and lateral outflow
  9. Hot compression deformation of an Mg–2.54Nd–0.26Zn–0.32Zr alloy
  10. Evaluation of the sliding performance of polyamide, poly-oxy-methylene and their composites
  11. Corrosion behaviour of AISI 204Cu and AISI 304 stainless steels in simulated pore solution
  12. Comparing the corrosion behavior of nanograined and coarse-grained interstitial free steels
  13. Electrochemical investigation of the effect of different laser surface treatments on Hastelloy G alloy
  14. Influence of sputtering gas pressure on properties of transparent conducting Si-doped zinc oxide films
  15. Cu2SnS3 absorber thin films prepared via successive ionic layer adsorption and reaction method
  16. Nano preparation of Dy3+ substituted ceria via urea-formaldehyde gel combustion route
  17. Short Communications
  18. Preparation of ZrB2-based nanocomposites with limited grain growth by means of low-temperature hot-pressing using Cu additive
  19. Combustion synthesis of Ti2SC
  20. People
  21. Prof. Dr. Tomaž Kosmač
  22. DGM News
  23. DGM News
https://doi.org/10.3139/146.110956
Keywords for this article
Corrosion; Interstitial free steel; Wire brushing; Nanostructure; Severe plastic deformation

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Martensite–austenite transformation kinetics of high Cr ferritic heat-resistant steel
  5. Ageing texture of hot rolled and solution treated Ti–Nb alloys
  6. Artificial aging of thixocast ZA27 alloy and particulate ZA27/SiCp composites
  7. Low cycle fatigue behavior under asymmetric loading of two AZ31B magnesium alloys with different microstructures and textures
  8. Mechanical properties of aluminum extruded via the KOBO method with direct and lateral outflow
  9. Hot compression deformation of an Mg–2.54Nd–0.26Zn–0.32Zr alloy
  10. Evaluation of the sliding performance of polyamide, poly-oxy-methylene and their composites
  11. Corrosion behaviour of AISI 204Cu and AISI 304 stainless steels in simulated pore solution
  12. Comparing the corrosion behavior of nanograined and coarse-grained interstitial free steels
  13. Electrochemical investigation of the effect of different laser surface treatments on Hastelloy G alloy
  14. Influence of sputtering gas pressure on properties of transparent conducting Si-doped zinc oxide films
  15. Cu2SnS3 absorber thin films prepared via successive ionic layer adsorption and reaction method
  16. Nano preparation of Dy3+ substituted ceria via urea-formaldehyde gel combustion route
  17. Short Communications
  18. Preparation of ZrB2-based nanocomposites with limited grain growth by means of low-temperature hot-pressing using Cu additive
  19. Combustion synthesis of Ti2SC
  20. People
  21. Prof. Dr. Tomaž Kosmač
  22. DGM News
  23. DGM News
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2026 De Gruyter Brill
Downloaded on 1.2.2026 from https://www.degruyterbrill.com/document/doi/10.3139/146.110956/html
Scroll to top button