Startseite Mechanical and tribological properties of a WC-based HVOF spray coated brake disc
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Mechanical and tribological properties of a WC-based HVOF spray coated brake disc

  • Halil Kılıç EMAIL logo , Cenk Mısırlı , İbrahim Mutlu und Mustafa Timur
Veröffentlicht/Copyright: 5. August 2022
Veröffentlichen auch Sie bei De Gruyter Brill
Manuskript einreichen Informationen für Autor*innen
Materials Testing
Aus der Zeitschrift Materials Testing Band 64 Heft 8

Abstract

Thermally sprayed WC-based coating systems are generally used to increase engineering components’ wear resistance. This research presents the results of a comparative study conducted to examine the tribological characteristics of a new brake disc created with thermal sprayed WC-10Co4Cr coating. This study implemented braking tests on the WC-10Co4Cr coated brake disc against commercial friction material on a laboratory scale disc-pad tester and compared the findings with the reference disc. The coating system was created with a high velocity oxygen-fuel spraying on a cast iron disc. The braking tests followed the sections of the SAE-J2430 test procedure. The microstructure, phase composition and properties of the coating were characterized by SEM/EDS, XRD and Vickers microstructure. The effect of carbide coating on the friction and wear behaviour of the tribological system was examined. The WC-10Co4Cr coating has increased the hardness by 3 times with a thickness of 300 μm compared to the cast iron surface. The amount of wear in the coated disc (CD) was reduced by about 85% compared to the reference disc (BD). The coefficient of frictions of BD and CD was found to be in the range of 0.43–0.61 and 0.47–0.62, respectively. The inclusion of hard phases (WC and W2C) in the disc coating played an important role in improving the sliding wear resistance by maintaining the coefficient of friction of the brake disc at an acceptable level. In brief, carbide coating could be claimed to be promising for challenging braking implementations.

Keywords: brake disc; HVOF; tribology; WC-CoCr coating; wear
Corresponding author: Halil Kılıç, Department of Machine, Technical Sciences Vocational School, Kırklareli University, Kirklareli, Turkey, E-mail:

  1. Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.

  2. Research funding: None declared.

  3. Conflict of interest statement: The authors declare no conflicts of interest regarding this article.

References

[1] P. Chandra Verma, L. Menapace, A. Bonfanti, R. Ciudin, S. Gialanella, and G. Straffelini, “Braking pad-disc system: wear mechanisms and formation of wear fragments,” Wear, vols. 322–323, pp. 251–258, 2015, https://doi.org/10.1016/j.wear.2014.11.019.Suche in Google Scholar

[2] T. Grigoratos and G. Martini, “Brake wear particle emissions: a review,” Environ. Sci. Pollut. Res., vol. 22, no. 4, pp. 2491–2504, 2015, https://doi.org/10.1007/s11356-014-3696-8.Suche in Google Scholar

[3] G. Cueva, A. Sinatora, W. L. Guesser, and A. P. Tschiptschin, “Wear resistance of cast irons used in brake disc rotors,” Wear, vol. 255, nos. 7–12, pp. 1256–1260, 2003, https://doi.org/10.1016/S0043-1648(03)00146-7.Suche in Google Scholar

[4] D. S. T. Hjortenkrans, B. G. Bergbäck, and A. V. Häggerud, “Metal emissions from brake linings and tires: case studies of Stockholm, Sweden 1995/1998 and 2005,” Environ. Sci. Technol., vol. 41, no. 15, pp. 5224–5230, 2007, https://doi.org/10.1021/es070198o.Suche in Google Scholar PubMed

[5] E. Furusjö, J. Sternbeck, and A. P. Cousins, “PM10 source characterization at urban and highway roadside locations,” Sci. Total Environ., vol. 387, nos. 1–3, pp. 206–219, 2007, https://doi.org/10.1016/j.scitotenv.2007.07.021.Suche in Google Scholar PubMed

[6] M. Djafri, M. Bouchetara, C. Busch, and S. Weber, “Effects of humidity and corrosion on the tribological behaviour of the brake disc materials,” Wear, vol. 321, pp. 8–15, 2014, https://doi.org/10.1016/j.wear.2014.09.006.Suche in Google Scholar

[7] M. Timur and H. Kılıc, “Marble waste using produced of automotive brake pad of friction coefficient different pad brake pads with comprasion,” Pamukkale Univ. J. Eng. Sci., vol. 19, no. 1, pp. 10–14, 2013, https://doi.org/10.5505/pajes.2013.55264.Suche in Google Scholar

[8] A. Keskin, “Investigation of using natural zeolite in brake pad,” Sci. Res. Essays, vol. 6, no. 23, pp. 4893–4904, 2011, https://doi.org/10.5897/SRE10.1072.Suche in Google Scholar

[9] H. Öktem, S. Akıncıoğlu, İ. Uygur, and G. Akıncıoğlu, “A novel study of hybrid brake pad composites: new formulation, tribological behaviour and characterisation of microstructure,” Plast., Rubber Compos., vol. 50, no. 5, pp. 249–261, 2021, https://doi.org/10.1080/14658011.2021.1898881.Suche in Google Scholar

[10] G. Straffelini, P. V. Chandra, I. Metinoz, R. Ciudin, G. Perricone, and S. Gialanella, “Wear behavior of a low metallic friction material dry sliding against a cast iron disc: role of the heat-treatment of the disc,” Wear, vols. 348–349, pp. 10–16, 2016, https://doi.org/10.1016/j.wear.2015.11.020.Suche in Google Scholar

[11] T. Grabiec, “Wear and friction behavior of friction pairs tested with different types of grey cast iron and low met friction material,” SAE Int. J. Passeng. Cars – Mech. Syst., vol. 7, no. 4, pp. 1361–1368, 2014, https://doi.org/10.4271/2014-01-2525.Suche in Google Scholar

[12] M. Federici, C. Menapace, A. Moscatelli, S. Gialanella, and G. Straffelini, “Effect of roughness on the wear behavior of HVOF coatings dry sliding against a friction material,” Wear, vols. 368–369, pp. 326–334, 2016, https://doi.org/10.1016/j.wear.2016.10.013.Suche in Google Scholar

[13] H. Kılıç, C. Mısırlı, and İ. Mutlu, “Investigation of the friction behavior of plasma spray Mo/NiCrBSi coated brake discs,” Mater. Test., vol. 63, no. 3, pp. 259–265, 2021, https://doi.org/10.1515/mt-2020-0038.Suche in Google Scholar

[14] B. Güney, “Corrosion and wear behaviour of HVOF spraying WC-12% Ni coating on gray cast-iron,” Indian J. Eng. Mater. Sci., vol. 28, no. 1, pp. 73–81, 2021.10.56042/ijems.v28i1.34970Suche in Google Scholar

[15] G. Bolelli, A. Colella, L. Lusvarghi et al., “TiC–NiCr thermal spray coatings as an alternative to WC-CoCr and Cr3C2–NiCr,” Wear, vols. 450–451, 2020, Art. no. 203273, https://doi.org/10.1016/j.wear.2020.203273.Suche in Google Scholar

[16] S. Özel, “Microstructure and mechanical properties of HVOF sprayed WC-Co/NiCrBSi, Cr3C2 coatings on Al alloys,” Mater. Test., vol. 55, no. 9, pp. 694–700, 2013, https://doi.org/10.3139/120.110489.Suche in Google Scholar

[17] B. Güney and I. Mutlu, “Dry friction behavior of NiCrBSi-%35W2C coated brake disks,” Mater. Test., vol. 59, no. 5, pp. 497–505, 2017, https://doi.org/10.3139/120.111030.Suche in Google Scholar

[18] A. C. Karaoglanli, M. Oge, K. M. Doleker, and M. Hotamis, “Comparison of tribological properties of HVOF sprayed coatings with different composition,” Surf. Coat. Technol., vol. 318, pp. 299–308, 2017, https://doi.org/10.1016/j.surfcoat.2017.02.021.Suche in Google Scholar

[19] X. Guo, M.-P. Planche, J. Chen, and H. Liao, “Relationships between in-flight particle characteristics and properties of HVOF sprayed WC-CoCr coatings,” J. Mater. Process. Technol., vol. 214, no. 2, pp. 456–461, 2014, https://doi.org/10.1016/j.jmatprotec.2013.09.029.Suche in Google Scholar

[20] A. Bansal, J. Singh, and H. Singh, “Slurry erosion behavior of HVOF-sprayed WC-10Co-4Cr coated SS 316 steel with and without PTFE modification,” J. Therm. Spray Technol., vol. 28, no. 7, pp. 1448–1465, 2019, https://doi.org/10.1007/S11666-019-00903-Y.Suche in Google Scholar

[21] M. Federici, C. Menapace, A. Moscatelli, S. Gialanella, and G. Straffelini, “Pin-on-disc study of a friction material dry sliding against HVOF coated discs at room temperature and 300 °C,” Tribol. Int., vol. 115, pp. 89–99, 2017, https://doi.org/10.1016/j.triboint.2017.05.030.Suche in Google Scholar

[22] H. Kılıç and C. Mısırlı, “Research on tribological behavior of Cr3C2-25NiCr coated brake disc,” Surf. Rev. Lett., vol. 28, no. 10, Art. no. 2150097, 2021, https://doi.org/10.1142/S0218625X21500979.Suche in Google Scholar

[23] J. Wahlström, Y. Lyu, V. Matjeka, and A. Söderberg, “A pin-on-disc tribometer study of disc brake contact pairs with respect to wear and airborne particle emissions,” Wear, vols. 384–385, pp. 124–130, 2017, https://doi.org/10.1016/j.wear.2017.05.011.Suche in Google Scholar

[24] X. Ding, D. Ke, C. Yuan, Z. Ding, and X. Cheng, “Microstructure and cavitation erosion resistance of HVOF deposited WC-Co coatings with different sized WC,” Coatings, vol. 8, no. 9, Art. no. 307, 2018, https://doi.org/10.3390/coatings8090307.Suche in Google Scholar

[25] E. Celik, O. Culha, B. Uyulgan, N. F. Ak Azem, I. Ozdemir, and A. Turk, “Assessment of microstructural and mechanical properties of HVOF sprayed WC-based cermet coatings for a roller cylinder,” Surf. Coat. Technol., vol. 200, nos. 14–15, pp. 4320–4328, 2006, https://doi.org/10.1016/j.surfcoat.2005.02.158.Suche in Google Scholar

[26] A. Karimi, C. Verdon, and G. Barbezat, “Microstructure and hydroabrasive wear behaviour of high velocity oxy-fuel thermally sprayed WC-Co(Cr) coatings,” Surf. Coat. Technol., vol. 57, no. 1, pp. 81–89, 1993, https://doi.org/10.1016/0257-8972(93)90340-T.Suche in Google Scholar

[27] G. Bolelli, L. M. Berger, T. Börner, et al., “Tribology of HVOF- and HVAF-sprayed WC-10Co4Cr hardmetal coatings: a comparative assessment,” Surf. Coat. Technol., vol. 265, pp. 125–144, 2015, https://doi.org/10.1016/j.surfcoat.2015.01.048.Suche in Google Scholar

[28] J. A. Picas, M. Punset, M. T. Baile, E. Martín, and A. Forn, “Effect of oxygen/fuel ratio on the in-flight particle parameters and properties of HVOF WC-CoCr coatings,” Surf. Coat. Technol., vol. 205, pp. 364–368, 2011, https://doi.org/10.1016/j.surfcoat.2011.03.129.Suche in Google Scholar

[29] I. Hulka, V. A. Şerban, I. Secoşan, P. Vuoristo, and K. Niemi, “Wear properties of CrC-37WC-18M coatings deposited by HVOF and HVAF spraying processes,” Surf. Coat. Technol., vol. 210, pp. 15–20, 2012, https://doi.org/10.1016/j.surfcoat.2012.07.077.Suche in Google Scholar

[30] M. Xie, S. Zhang, and M. Li, “Comparative investigation on HVOF sprayed carbide-based coatings,” Appl. Surf. Sci., vol. 273, pp. 799–805, 2013, https://doi.org/10.1016/J.APSUSC.2013.03.010.Suche in Google Scholar

[31] P. Chivavibul, M. Watanabe, S. Kuroda, and K. Shinoda, “Effects of carbide size and Co content on the microstructure and mechanical properties of HVOF-sprayed WC–Co coatings,” Surf. Coat. Technol., vol. 202, no. 3, pp. 509–521, 2007, https://doi.org/10.1016/j.surfcoat.2007.06.026.Suche in Google Scholar

[32] D. Wang, B. Zhang, C. Jia et al., “Influence of carbide grain size and crystal characteristics on the microstructure and mechanical properties of HVOF-sprayed WC-CoCr coatings,” Int. J. Refract. Metals Hard Mater., vol. 69, pp. 138–152, 2017, https://doi.org/10.1016/j.ijrmhm.2017.08.008.Suche in Google Scholar

[33] Y. Dilay, B. Güney, A. Özkan, and A. Öz, “Microstructure and wear properties of WC–10Co–4Cr coating to cultivator blades by DJ-HVOF,” Emerg. Mater. Res., vol. 10, no. 3, pp. 278–288, 2021, https://doi.org/10.1680/jemmr.20.00324.Suche in Google Scholar

[34] G. Straffelini and L. Maines, “The relationship between wear of semimetallic friction materials and pearlitic cast iron in dry sliding,” Wear, vol. 307, nos. 1–2, pp. 75–80, 2013, https://doi.org/10.1016/j.wear.2013.08.020.Suche in Google Scholar

[35] G. Bolelli, L.-M. Berger, M. Bonetti, and L. Lusvarghi, “Comparative study of the dry sliding wear behaviour of HVOF-sprayed WC–(W,Cr)2C–Ni and WC–CoCr hardmetal coatings,” Wear, vol. 309, nos. 1–2, pp. 96–111, 2014, https://doi.org/10.1016/j.wear.2013.11.001.Suche in Google Scholar

[36] H. V. Ozkavak, S. Sahin, M. F. Sarac, and Z. Alkan, “Wear properties of WC–Co and WC–CoCr coatings applied by HVOF technique on different steel substrates,” Mater. Test., vol. 62, no. 12, pp. 1235–1242, 2020, https://doi.org/10.3139/120.111609.Suche in Google Scholar

[37] I. D. Utu, I. Hulka, and V. A. Serban, “Microstructure and abrasion wear resistance of thermally sprayed cermet coatings,” Mater. Test., vol. 55, no. 1, pp. 47–50, 2013, https://doi.org/10.3139/120.110402.Suche in Google Scholar

[38] M. Akkaş, “The mechanical and corrosion properties of WCCo–Al coatings formed on AA2024 using the HVOF method,” Mater. Res. Express, vol. 7, no. 7, 2020, Art. no. 076515, https://doi.org/10.1088/2053-1591/ab9fba.Suche in Google Scholar

[39] Y. Wu, S. Hong, J. Zhang et al., “Microstructure and cavitation erosion behavior of WC–Co–Cr coating on 1Cr18Ni9Ti stainless steel by HVOF thermal spraying,” Int. J. Refract. Metals Hard Mater., vol. 32, pp. 21–26, 2012, https://doi.org/10.1016/j.ijrmhm.2012.01.002.Suche in Google Scholar

[40] D. Kumar Goyal, H. Singh, H. Kumar, and V. Sahni, “Slurry erosion behaviour of HVOF sprayed WC–10Co–4Cr and Al2O3+13TiO2 coatings on a turbine steel,” Wear, vol. 289, pp. 46–57, 2012, https://doi.org/10.1016/j.wear.2012.04.016.Suche in Google Scholar

[41] A. Ghabchi, T. Varis, E. Turunen, T. Suhonen, X. Liu, and S.-P. Hannula, “Behavior of HVOF WC-10Co4Cr coatings with different carbide size in fine and coarse particle abrasion,” J. Therm. Spray Technol., vol. 19, nos. 1–2, pp. 368–377, 2010, https://doi.org/10.1361/cp2009itsc0415.Suche in Google Scholar

[42] M. Ceviz, C. Misirli, and S. S. Karabeyoglu, “The effect of temperature on wear Performance of high-velocity oxy-fuel sprayed WC-10Co-4Cr coating on AA7075-T6 Substrate,” J. Mater. Eng. Perform., vol. 31, no. 1, pp. 128–138, 2022, https://doi.org/10.1007/s11665-021-06169-2.Suche in Google Scholar

[43] L. Qiao, Y. Wu, S. Hong, W. Long, and J. Cheng, “Wet abrasive wear behavior of WC-based cermet coatings prepared by HVOF spraying,” Ceram. Int., vol. 47, no. 2, pp. 1829–1836, 2021, https://doi.org/10.1016/j.ceramint.2020.09.009.Suche in Google Scholar

[44] T. Sahraoui, N. E. Fenineche, G. Montavon, and C. Coddet, “Structure and wear behaviour of HVOF sprayed Cr3C2-NiCr and WC-Co coatings,” Mater. Des., vol. 24, no. 5, pp. 309–313, 2003, https://doi.org/10.1016/S0261-3069(03)00059-1.Suche in Google Scholar

[45] H. Kılıç and C. Mısırlı, “Investigation of tribological behavior of 20NiCrBSi-WC12Co coated brake disc by HVOF method,” Mater. Res. Express, vol. 7, no. 1, 2020, Art. no. 016560, https://doi.org/10.1088/2053-1591/ab61be.Suche in Google Scholar

[46] Q. Wang, Z. Chen, L. Li, and G. Yang, “The parameters optimization and abrasion wear mechanism of liquid fuel HVOF sprayed bimodal WC–12Co coating,” Surf. Coat. Technol., vol. 206, nos. 8–9, pp. 2233–2241, 2012, https://doi.org/10.1016/j.surfcoat.2011.09.071.Suche in Google Scholar

[47] A. G. Evans and T. R. Wilshaw, “Quasi-static solid particle damage in brittle solids-I. Observations analysis and implications,” Acta Metall., vol. 24, no. 10, pp. 939–956, 1976, https://doi.org/10.1016/0001-6160(76)90042-0.Suche in Google Scholar

[48] A. Mateen, G. C. Saha, T. I. Khan, and F. A. Khalid, “Tribological behaviour of HVOF sprayed near-nanostructured and microstructured WC-17wt%Co coatings,” Surf. Coat. Technol., vol. 206, no. 6, pp. 1077–1084, 2011, https://doi.org/10.1016/j.surfcoat.2011.07.075.Suche in Google Scholar

[49] Q. Yang, T. Senda, and A. Ohmori, “Effect of carbide grain size on microstructure and sliding wear behavior of HVOF-sprayed WC-12% Co coatings,” Wear, vol. 254, nos. 1–2, pp. 23–34, 2003, https://doi.org/10.1016/S0043-1648(02)00294-6.Suche in Google Scholar

[50] V. Rajinikanth and K. Venkateswarlu, “An investigation of sliding wear behaviour of WC–Co coating,” Tribol. Int., vol. 44, no. 12, pp. 1711–1719, 2011, https://doi.org/10.1016/j.triboint.2011.06.021.Suche in Google Scholar

[51] S. Usmani, S. Sampath, D. L. Houck, and D. Lee, “Effect of carbide grain size on the sliding and abrasive wear behavior of thermally sprayed WC-Co coatings,” Tribol. Trans., vol. 40, no. 3, pp. 470–478, 1997, https://doi.org/10.1080/10402009708983682.Suche in Google Scholar

[52] S. Hong, Y. Wu, B. Wang, J. Zhang, Y. Zheng, and L. Qiao, “The effect of temperature on the dry sliding wear behavior of HVOF sprayed nanostructured WC-CoCr coatings,” Ceram. Int., vol. 43, no. 1, pp. 458–462, 2017, https://doi.org/10.1016/j.ceramint.2016.09.180.Suche in Google Scholar

[53] N. Vashishtha, R. K. Khatirkar, and S. G. Sapate, “Tribological behaviour of HVOF sprayed WC-12Co, WC-10Co-4Cr and Cr3C2−25NiCr coatings,” Tribol. Int., vol. 105, pp. 55–68, 2017, https://doi.org/10.1016/j.triboint.2016.09.025.Suche in Google Scholar

[54] B. Güney and I. Mutlu, “Tribological properties of brake discs coated with Cr2O3-40% TiO2 by plasma spraying,” Surf. Rev. Lett., vol. 26, no. 10, 2019, Art. no. 1950075, https://doi.org/10.1142/S0218625X19500756.Suche in Google Scholar

[55] H. Qi and A. J. Day, “Investigation of disc/pad interface temperatures in friction braking,” Wear, vol. 262, nos. 5–6, pp. 505–513, 2007, https://doi.org/10.1016/j.wear.2006.08.027.Suche in Google Scholar

[56] P. Lee and P. Filip, “Friction and wear of Cu-free and Sb-free environmental friendly automotive brake materials,” Wear, vol. 302, nos. 1–2, pp. 1404–1413, 2013, https://doi.org/10.1016/j.wear.2012.12.046.Suche in Google Scholar

[57] R. Ahmed, O. Ali, N. H. Faisal et al., “Sliding wear investigation of suspension sprayed WC-Co nanocomposite coatings,” Wear, vols. 322–323, pp. 133–150, 2015, https://doi.org/10.1016/j.wear.2014.10.021.Suche in Google Scholar

[58] H. S. Sidhu, B. S. Sidhu, and S. Prakash, “Wear characteristics of Cr3C2-NiCr and WC-Co coatings deposited by LPG fueled HVOF,” Tribol. Int., vol. 43, nos. 5–6, pp. 887–890, 2010, https://doi.org/10.1016/j.triboint.2009.12.016.Suche in Google Scholar

[59] C. R. Raghavendra, S. Basavarajappa, and I. Sogalad, “Dry sliding wear behaviour of nano coating: influence of coating parameters and surface roughness,” Trans. Indian Inst. Met., vol. 74, no. 11, pp. 2887–2900, 2021, https://doi.org/10.1007/s12666-021-02365-9.Suche in Google Scholar
Published Online: 2022-08-05
Published in Print: 2022-08-26

© 2022 Walter de Gruyter GmbH, Berlin/Boston

Artikel in diesem Heft

  1. Frontmatter
  2. Effect of heat treatment on the electrical and mechanical properties of a Cu–Ni–Si cast alloy
  3. Effect of isothermal heat treatments under Ms temperature on the microstructures and mechanical properties of commercial high-silicon spring steel
  4. Effect of austenitizing temperature on microstructure and properties of a high-speed cobalt steel
  5. Effect of hot rolling process parameters on the microstructure and mechanical properties of continuously cooled low-carbon high-strength low-alloy (HSLA) steel
  6. Mechanical and tribological properties of a WC-based HVOF spray coated brake disc
  7. Microstructure and mechanical properties of AISI 304/DUROSTAT 500 steel double-sided TIG welds
  8. A Nelder Mead-infused INFO algorithm for optimization of mechanical design problems
  9. Modeling of hexagonal honeycomb hybrids for variation of Poisson’s ratio
  10. Effect of elevated test temperature on the tensile strength and failure mechanism of hot-pressed dissimilar joints of laser ablation-treated AA5754-H111 and thermoplastic composite
  11. Steel shot peening effects on friction stir welded AA2014-T6 aluminum alloys
  12. Improvement of incremental sheet metal forming with the help of a pressurised fluid system
  13. Nugget formation, microstructural features and strength of resistance spot welded cold-rolled dual-phase steel lap joints for automotive applications
  14. African vultures optimization algorithm for optimization of shell and tube heat exchangers
  15. Effect of welding current on properties of activated gas tungsten arc super duplex stainless steel welds
https://doi.org/10.1515/mt-2022-0077
Schlagwörter für diesen Artikel
brake disc; HVOF; tribology; WC-CoCr coating; wear

Artikel in diesem Heft

  1. Frontmatter
  2. Effect of heat treatment on the electrical and mechanical properties of a Cu–Ni–Si cast alloy
  3. Effect of isothermal heat treatments under Ms temperature on the microstructures and mechanical properties of commercial high-silicon spring steel
  4. Effect of austenitizing temperature on microstructure and properties of a high-speed cobalt steel
  5. Effect of hot rolling process parameters on the microstructure and mechanical properties of continuously cooled low-carbon high-strength low-alloy (HSLA) steel
  6. Mechanical and tribological properties of a WC-based HVOF spray coated brake disc
  7. Microstructure and mechanical properties of AISI 304/DUROSTAT 500 steel double-sided TIG welds
  8. A Nelder Mead-infused INFO algorithm for optimization of mechanical design problems
  9. Modeling of hexagonal honeycomb hybrids for variation of Poisson’s ratio
  10. Effect of elevated test temperature on the tensile strength and failure mechanism of hot-pressed dissimilar joints of laser ablation-treated AA5754-H111 and thermoplastic composite
  11. Steel shot peening effects on friction stir welded AA2014-T6 aluminum alloys
  12. Improvement of incremental sheet metal forming with the help of a pressurised fluid system
  13. Nugget formation, microstructural features and strength of resistance spot welded cold-rolled dual-phase steel lap joints for automotive applications
  14. African vultures optimization algorithm for optimization of shell and tube heat exchangers
  15. Effect of welding current on properties of activated gas tungsten arc super duplex stainless steel welds
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 11.9.2025 von https://www.degruyterbrill.com/document/doi/10.1515/mt-2022-0077/html
Button zum nach oben scrollen