Startseite Optical and temperature dependent electrical properties of poly (vinyl chloride)/copper alumina nanocomposites for optoelectronic devices
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Optical and temperature dependent electrical properties of poly (vinyl chloride)/copper alumina nanocomposites for optoelectronic devices

  • S. Suvarna , Annumaria Sebastian , Furhan und Manammel Thankappan Ramesan EMAIL logo
Veröffentlicht/Copyright: 26. Dezember 2022
Veröffentlichen auch Sie bei De Gruyter Brill
Manuskript einreichen Informationen für Autor*innen
International Polymer Processing
Aus der Zeitschrift International Polymer Processing Band 38 Heft 2

Abstract

The practical applications of poly (vinyl chloride) have been constrained due to its poor thermal stability, low dielectric constant and inability to shield against ultraviolet (UV) radiation. In this study, we tried to improve the optical properties, thermal stability, temperature-dependent electrical conductivity and dielectric constant using copper alumina (Cu–Al2O3) nanoparticles reinforced poly (vinyl chloride) (PVC). Optical absorption measured with an ultraviolet-visible (UV-visible) spectrometer emphasises the blueshift in absorption edges and decreasing bandgap energies of PVC/Cu–Al2O3 nanocomposites compared to PVC. The presence of Cu–Al2O3 in PVC and its interaction with the polymer were confirmed by FTIR spectroscopy. Thermogravimetric analysis (TGA) demonstrates that nanocomposites have higher thermal stability than PVC, and that thermal stability increases with filler loading. Scanning electron microscopy (SEM) indicates the homogeneous dispersion of nanosized Cu–Al2O3 in the polymer matrix. The activation energy determined by the Arrhenius equation revealed that AC conductivity increases with the addition of nanoparticles up to a specific loading. The dielectric constant increases as a function of temperature and decreases with frequency. The magnitude of AC conductivity and dielectric constant were highest for 7 wt% loaded nanocomposites. The dielectric constant predicted by the Bruggeman and Maxwell-Garnet models were in good agreement with the experimental permittivity. The semiconducting nature of nanocomposites was investigated by impedance analysis. The semi-circular nature of Cole-Cole plots manifests the combination of parallel capacitance with low bulk resistance. The enhanced optical, thermal, electrical and dielectric properties of PVC/Cu–Al2O3 nanocomposites can be utilized in fabricating optoelectronic devices with excellent charge-storing ability.

Keywords: copper alumina; dielectric parameters; modelling; nanocomposites; optical properties; poly(vinyl chloride); temperature-dependent conductivity; thermal stability
Corresponding author: Manammel Thankappan Ramesan, Department of Chemistry, Centre for Polymer Science and Technology, University of Calicut, Calicut University P.O., Kerala, Malappuram, 673 635 India, E-mail:

  1. Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.

  2. Research funding: None declared.

  3. Conflict of interest statement: The authors of this article have no conflict of interest to declare.

References

Ahmed, R.M., Atta, M.M., and Taha, E.O. (2021). Optical spectroscopy, thermal analysis, and dynamic mechanical properties of graphene nano-platelets reinforced polyvinylchloride. J. Mater. Sci. Mater. Electron. 32: 22699–22717, https://doi.org/10.1007/s10854-021-06756-y.Suche in Google Scholar

Aribou, A., Bouazzaoui, S.E., Achour, M.E., Costa, L.C., Mohamed, B., and Outzourhit, A. (2012). Thermal and spectral dielectric properties of polypyrrole/polymethylmethacrylate composites. Spectrosc. Lett. 45: 477–481, https://doi.org/10.1080/00387010.2012.667035.Suche in Google Scholar

Beneš, M., Plaček, V., Matuschek, G., Kettrup, A., Gyoryova, K., and Balek, V. (2005). Characterization of PVC cable insulation materials and products obtained after removal of additives. J. Appl. Polym. Sci. 99: 788–795, https://doi.org/10.1002/app.22559.Suche in Google Scholar

Bruno, G., Kachanov, M., Sevostianov, I., and Shyam, A. (2018). Micromechanical modeling of non-linear stress-strain behavior of polycrystalline microcracked materials under tension. Acta Mater. 164: 50–59, https://doi.org/10.1016/j.actamat.2018.10.024.Suche in Google Scholar

Bulut, M., Alsaadi, M., and Erkliğ, A. (2020). The effects of nanosilica and nanoclay particles inclusions on mode II delamination, thermal and water absorption of intraply woven carbon/aramid hybrid composites. Int. Polym. Proc. 35: 367–375, https://doi.org/10.3139/217.3940.Suche in Google Scholar

Cappellin, G.R.D., Sole, L., and Reining, F. (1993). Model dielectric function for semiconductors. Phys. Rev., B 47: 9892–9895, https://doi.org/10.1103/physrevb.47.9892.Suche in Google Scholar PubMed

Charvani, S., Reddy, S.S.K., and Narendar, G. (2018). Preparation and characterization of alumina nanocomposites. Mater. Today Proced. 5: 51381, https://doi.org/10.1016/j.matpr.2018.08.162.Suche in Google Scholar

Chen, R.S., Ahmad, S., and Gan, S. (2017). Characterization of recycled thermoplastics-based nanocomposites: polymer-clay compatibility, blending procedure, processing condition, and clay content effects. Compos. B. Eng. 131: 91–99, https://doi.org/10.1016/j.compositesb.2017.07.057.Suche in Google Scholar

Diniz, M.O., Coelho, R.S., Bianchi, R.F., and Guerra, E.M (2021). Electrical impedance of V2O5/POMA hybrid film deposited by casting for application in ammonia gas sensor. J. Electron. Mater. 50: 450–455, https://doi.org/10.1007/s11664-020-08587-9.Suche in Google Scholar

Dulaurent, O., Courtois, X., Perrichon, V., and Bianchi, D. (2000). Heats of Adsorption of CO on a Cu/Al2O3 catalyst using FTIR spectroscopy at high temperatures and under adsorption equilibrium conditions. J. Phys. Chem. B 104: 6001–6011, https://doi.org/10.1021/jp9943629.Suche in Google Scholar

Ebnalwaled, A.A. and Thabet, A. (2016). Controlling the optical constants of PVC nanocomposite films for optoelectronic applications. Synth. Met. 220: 374, https://doi.org/10.1016/j.synthmet.2016.07.006.Suche in Google Scholar

Elimat, Z.M. (2013). AC-impedance and dielectric properties of hybrid polymer composites. J. Compos. Mater. 49: 3–15, https://doi.org/10.1177/0021998313514256.Suche in Google Scholar

El-Khiyami, S.S., Ismail, A.M., and Hafez, R.S. (2021). Characterization, optical and conductivity study of nickel oxide-based nanocomposites of polystyrene. J. Inorg. Organomet. Polym. Mater. 31: 4313–4325, https://doi.org/10.1007/s10904-021-02041-x.Suche in Google Scholar

Ezzat, M., Sabiha, N.A., and Izzularab, M. (2013). Accurate model for computing dielectric constant of dielectric nanocomposites. Appl. Nanosci. 4: 331–338, https://doi.org/10.1007/s13204-013-0201-5.Suche in Google Scholar

Furhan and Ramesan, M.T. (2022a). Zinc oxide reinforced poly(para-aminophenol) nanocomposites: structural, thermal stability, conductivity and ammonia gas sensing applications. J. Macromol. Sci. A 59: 675–688, https://doi.org/10.1080/10601325.2022.2111262.Suche in Google Scholar

Furhan and Ramesan, M.T. (2022b). Enhanced dielectric properties, thermal stability and ammonia sensing performance of poly(diphenylamine)/ZnO nanocomposites via one step polymerization. J. Appl. Polym. Sci. 139: e52913, https://doi.org/10.1002/app.52913.Suche in Google Scholar

Furhan Vyshakh, K. and Ramesan, M.T. (2022). Enhanced optical properties, thermal transitions, temperature-dependent electrical properties and modelling studies of poly(diphenylamine)/NiO nanocomposites”. J. Mater. Sci. 57: 18385–18405, https://doi.org/10.1007/s10853-022-07759-8.Suche in Google Scholar

Ghanbari, A., Heuzey, M.C., and Carreau, P.J. (2021). The effect of nanosilicates on the performance of polyethylene terephthalate films prepared by twin-screw extrusion. Int. Polym. Proc. 36: 358–366, https://doi.org/10.1515/ipp-2020-4044.Suche in Google Scholar

Glogowski, E., Tangirala, R., Russell, T.P., and Emrick, T. (2006). Functionalization of nanoparticles for dispersion in polymers and assembly in fluids. J. Polym. Sci. A. Polym. Chem. 44: 5076–5086, https://doi.org/10.1002/pola.21598.Suche in Google Scholar

Hajibeygi, M., Maleki, M., and Shabanian, M. (2018). New polyvinyl chloride (PVC) nanocomposite consisting of aromatic polyamide and chitosan modified ZnO nanoparticles with enhanced thermal stability, low heat release rate and improved mechanical properties. Appl. Surf. Sci. 439: 1163–1179, https://doi.org/10.1016/j.apsusc.2018.01.255.Suche in Google Scholar

Hirschler, M.M. (1986). Thermal decomposition (STA and DSC) of PVC compounds under a variety of atmospheres and heating rates. Eur. Polym. J. 22: 153–160, https://doi.org/10.1016/0014-3057(86)90111-4.Suche in Google Scholar

Hussain, N., Mehdi, M., and Siyal, S.H. (2021). Conductive and antibacterial cellulose nanofibers decorated with copper nanoparticles for potential application in wearable devices. J. Appl. Polym. Sci. 138: 51381, https://doi.org/10.1002/app.51381.Suche in Google Scholar

Idumah, C.I., Hassan, A., and Ogbu, J. (2018). Recently emerging advancements in halloysite nanotubes polymer nanocomposites. Compos. Interfaces 26: 751–824, https://doi.org/10.1080/09276440.2018.1534475.Suche in Google Scholar

Joshi, G.M. and Deshmukh, K. (2014). Optimized quality factor of graphene oxide-reinforced PVC nanocomposite. J. Electron. Mater. 43: 1161–1165, https://doi.org/10.1007/s11664-014-3010-z.Suche in Google Scholar

Karpagavel, K., Sunndaramahalingam, K., Manikandan, A., Vanitha, D., Manohar, A., Nagarajan, E.R., and Nallamuthu, N. (2021). Electrical properties of lithium-ion conducting poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP)/polyvinylpyrrolidone (PVP) solid polymer electrolyte. J. Electron. Mater. 50: 4415–4425, https://doi.org/10.1007/s11664-021-08967-9.Suche in Google Scholar

Kour, P., Pradhan, S.K., Kumar, P., Sinha, S.K., and Manoranjan, K (2018). Effect of Nd doping on dielectric and impedance properties of PZT Nanoceramics. J. Electron. Mater. 47: 2861–2870, https://doi.org/10.1007/s11664-018-6151-7.Suche in Google Scholar

Maji, P., Pande, P.P., and Choudhary, R.B. (2015). Effect of Zn(NO3)2 filler on the dielectric permittivity and electrical modulus of PMMA. Bull. Mater. Sci. 38: 417–424, https://doi.org/10.1007/s12034-015-0886-z.Suche in Google Scholar

Muzaffa, A., Ahamed, M.B., Deshmukh, K., and Faisal, M. (2019). Electromagnetic interference shielding properties of polyvinylchloride (PVC), barium titanate (BaTiO3) and nickel oxide (NiO) based nanocomposites. Polym. Test. 77: 105925, https://doi.org/10.1016/j.polymertesting.2019.105925.Suche in Google Scholar

Özkan, V., Yapici, A., and Karaaslan, M. (2020). Electromagnetic scattering properties of MWCNTs/graphene doped epoxy layered with PVC nanofiber/E-glass composites. J. Electron. Mater. 49: 2249–2256, https://doi.org/10.1007/s11664-019-07921-0.Suche in Google Scholar

Parvathi, K. and Ramesan, M.T. (2022). Insights into structural, thermal, electrical and mechanical properties of copper alumina reinforced chlorinated natural rubber nanocomposites. J. Thermoplast. Comp. Mater., https://doi.org/10.1177/08927057221083495.Suche in Google Scholar

Parvathi, K., Bahuleyan, B.K., and Ramesan, M.T. (2022a). Optical, thermal and temperature dependent electrical properties of chlorinated natural rubber/copper alumina nanocomposites for flexible electrochemical devices. Res. Chem. Intermed. 48: 3897–3914, https://doi.org/10.1007/s11164-022-04790-x.Suche in Google Scholar

Parvathi, K., Bahuleyan, B.K., and Ramesan, M.T. (2022b). Flexible conductive nanocomposites for electrochemical devices based on chlorinated natural rubber/nickel oxide nanoparticles. J. Inorg. Organomet. Polym. 32: 2827–2842, https://doi.org/10.1007/s10904-022-02307-y.Suche in Google Scholar

Rodolfo, A. and Mei, L.H.I. (2010). Poly (vinyl chloride)/metallic oxides/organically modified montmorillonite nanocomposites, preparation, morphological characterization, and modeling of the mechanical properties. J. Appl. Polym. Sci. 116: 422–432, https://doi.org/10.1002/app.31442.Suche in Google Scholar

Roy, A.S., Saravanan, S., Kishore, Ramamurthy, P.C., and Madras, G., Ramamurthy, P.C., Madras, G. (2013). Dielectric impedance studies of poly (vinyl butyral)-cenosphere composite films. Polym. Compos. 35: 1636–1643, https://doi.org/10.1002/pc.22817.Suche in Google Scholar

Rybiński, P. (2017). Influence of carbon fillers on thermal properties and flammability of polymeric nanocomposites. Int. Polym. Proc. 32: 270–289, https://doi.org/10.3139/217.3316.Suche in Google Scholar

Saad, A.L.G., Aziz, H.A., and Dimitr, O.I.H. (2003). Studies of electrical and mechanical properties of poly (vinyl chloride) mixed with electrically conductive additives. J. Appl. Polym. Sci. 91: 1590–1598, https://doi.org/10.1002/app.13239.Suche in Google Scholar

Sankar, S. and Ramesan, M.T. (2022a). Synthesis, characterization, conductivity and gas sensing performance of copolymer nanocomposites based on copper alumina and poly (aniline-co-pyrrole). Polym. Eng. Sci. 62: 2402–2410, https://doi.org/10.1002/pen.26014.Suche in Google Scholar

Sankar, S. and Ramesan, M.T. (2022b). Thermal, optical and temperature dependent electrical properties poly(aniline-co-pyrrole)/copper alumina nanocomposites for optoelectronic devices. J. Therm. Anal. Calorim. 147: 13375–13387, https://doi.org/10.1007/s10973-022-11670-4.Suche in Google Scholar

Sankar, S. and Ramesan, M.T. (2022). Studies on optical properties, thermal stability and electrical conductivity of copper alumina nanoparticles reinforced poly(pyrrole-co-indole) for optoelectronic devices. J. Mat. Sci. Mat. Electron. 33: 21762–21777, https://doi.org/10.1007/s10854-022-08965-5.Suche in Google Scholar

Sharma, N., Patial, B.S., and Thakur, N. (2019). On the dielectric study and AC conductivity measurements of quaternary Se-Te-Ge-Pb nano-chalcogenide alloys. J. Electron. Mater. 48: 7089–7098, https://doi.org/10.1007/s11664-019-07520-z.Suche in Google Scholar

Shimoga, G., Shin, E.J., and Kim, S.Y. (2019). Thermal, dielectric and catalytic behavior of palladium doped PVC films. Polímeros 29: 724, https://doi.org/10.1590/0104-1428.08718.Suche in Google Scholar

Suvarna, S. and Furhan Ramesan, M.T. (2022). Optical and electrical properties of copper alumina nanoparticles reinforced chlorinated polyethylene composites for optoelectronic devices. J. Indian Chem. Soc. 99: 100772, https://doi.org/10.1016/j.jics.2022.100772.Suche in Google Scholar

Wang, P. and Kazuya, K. (2014). Synthetic versatility of nanoparticles: a new, rapid, one-pot, single-step synthetic approach to spherical mesoporous (metal) oxide nanoparticles using supercritical alcohols. Pure Appl. Chem. 86: 785–800, https://doi.org/10.1515/pac-2013-1117.Suche in Google Scholar

Zhou, C.W., Zhao, J.X., Liu, Q., et al.. (2013). Study on mechanical, thermal properties and morphology of biodegradable poly(butylene succinate)/nano-TiO2 composites. Int. Polym. Proc. 28: 483–488, https://doi.org/10.3139/217.2750.Suche in Google Scholar
Received: 2022-08-17
Accepted: 2022-12-03
Published Online: 2022-12-26
Published in Print: 2023-05-25

© 2022 Walter de Gruyter GmbH, Berlin/Boston

Artikel in diesem Heft

  1. Frontmatter
  2. Research Articles
  3. Influence of process parameters of a continuous final mixer on the properties of carbon black/rubber composites
  4. Time series data for process monitoring in injection molding: a quantitative study of the benefits of a high sampling rate
  5. Vibration damping properties of graphene nanoplatelets filled glass/carbon fiber hybrid composites
  6. Optical and temperature dependent electrical properties of poly (vinyl chloride)/copper alumina nanocomposites for optoelectronic devices
  7. Numerical visualization of extensional flows in injection molding of polymer melts
  8. Thermal, mechanical and dielectric properties of glass fiber reinforced epoxy-lanthanum manganite nanocomposites
  9. Statistical research on the mixing properties of wave based screws by numerical simulations
  10. Influence of mold cavity thickness on electrical, morphological and thermal properties of polypropylene/carbon micromoldings
  11. Development of a prototype for the rubber latex industry to detect dry rubber content of fresh natural rubber latex using a novel measurement system with proton-electron transfer
  12. Effect of molding history on molecular orientation relaxation during physical aging of polystyrene injection moldings
  13. A comparative analysis of the effect of post production treatments and layer thickness on tensile and impact properties of additively manufactured polymers
  14. Fabrication of flame-retardant and smoke-suppressant rigid polyurethane foam modified by hydrolyzed keratin
  15. Study on flame retardancy and thermal stability of rigid polyurethane foams modified by amino trimethylphosphonate cobalt and expandable graphite
  16. Three-dimensional simulation of capillary rheometry for an estimation of extensional viscosity
https://doi.org/10.1515/ipp-2022-4270
Schlagwörter für diesen Artikel
copper alumina; dielectric parameters; modelling; nanocomposites; optical properties; poly(vinyl chloride); temperature-dependent conductivity; thermal stability

Artikel in diesem Heft

  1. Frontmatter
  2. Research Articles
  3. Influence of process parameters of a continuous final mixer on the properties of carbon black/rubber composites
  4. Time series data for process monitoring in injection molding: a quantitative study of the benefits of a high sampling rate
  5. Vibration damping properties of graphene nanoplatelets filled glass/carbon fiber hybrid composites
  6. Optical and temperature dependent electrical properties of poly (vinyl chloride)/copper alumina nanocomposites for optoelectronic devices
  7. Numerical visualization of extensional flows in injection molding of polymer melts
  8. Thermal, mechanical and dielectric properties of glass fiber reinforced epoxy-lanthanum manganite nanocomposites
  9. Statistical research on the mixing properties of wave based screws by numerical simulations
  10. Influence of mold cavity thickness on electrical, morphological and thermal properties of polypropylene/carbon micromoldings
  11. Development of a prototype for the rubber latex industry to detect dry rubber content of fresh natural rubber latex using a novel measurement system with proton-electron transfer
  12. Effect of molding history on molecular orientation relaxation during physical aging of polystyrene injection moldings
  13. A comparative analysis of the effect of post production treatments and layer thickness on tensile and impact properties of additively manufactured polymers
  14. Fabrication of flame-retardant and smoke-suppressant rigid polyurethane foam modified by hydrolyzed keratin
  15. Study on flame retardancy and thermal stability of rigid polyurethane foams modified by amino trimethylphosphonate cobalt and expandable graphite
  16. Three-dimensional simulation of capillary rheometry for an estimation of extensional viscosity
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 18.9.2025 von https://www.degruyterbrill.com/document/doi/10.1515/ipp-2022-4270/html
Button zum nach oben scrollen