Startseite Interfacial reaction between Cu and Ti2SnC during processing of Cu–Ti2SnC composite
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Interfacial reaction between Cu and Ti2SnC during processing of Cu–Ti2SnC composite

  • Jinyi Wu , Yanchun Zhou EMAIL logo , Jingyang Wang , Wei Wang und Chengke Yan
Veröffentlicht/Copyright: 4. Februar 2022
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 96 Heft 11

Abstract

Interfacial reaction between Cu and Ti2SnC during the processing of Cu–Ti2SnC composite was investigated by using X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. It is shown that the reaction is closely related to the reaction temperature, reaction time, and relative ratio of Cu and Ti2SnC. The reacting products are Cu(Sn) solid solution and TiCx, and the transporting process during interfacial reaction is described. The interfacial reaction products are further confirmed by measuring the hardness across the interface using nanoindentation test. It is shown that the reaction is controlled by the de-intercalation of Sn from Ti2SnC to form Cu(Sn) solid solution and TiCx, and crystallographic relations of [01̅1] TiCx // [010] Ti2SnC and (11̅1̅) TiCx // (001) Ti2SnC were observed at the interface. The effect of interfacial reaction on the mechanical and electrical properties of the composite is also discussed.

Keywords: Interface; Copper; Ti2SnC; Metal matrix composites
Dr. Yanchun Zhou Professor and Director of High-performance Ceramic Division Shenyang National Laboratory for Materials Science Institute of Metal Research, Chinese Academy of Sciences 72 Wenhua Road, Shenyang 110016, P. R. China Tel.: +86 24 2397 1765 Fax: +86 24 2389 1320

References

[1] H. Ferkel: Nanostruct. Mater. 11 (1999) 595.10.1016/S0965-9773(99)00342-6Suche in Google Scholar

[2] A. Zúñiga, R. Palma, A. Sepúlveda, T. Löbel, L. Núñez: Key Eng.Mater. 189 (2001) 542.10.4028/www.scientific.net/KEM.189-191.542Suche in Google Scholar

[3] E.Y. Gutmanas, A. Trudler, I. Gotman: Mater. Sci. Forum 386 (2002) 329.10.4028/www.scientific.net/MSF.386-388.329Suche in Google Scholar

[4] S.F. Moustafa, S.A. El-Badry, A.M. Sanad: Powder Metall. 40 (1997) 201.10.1179/pom.1997.40.3.201Suche in Google Scholar

[5] K. Ichikawa, M. Achikita: Mater. Trans. JIM 34 (1993) 718.10.2320/matertrans1989.34.718Suche in Google Scholar

[6] A. Upadhyaya, G.S. Upadhyaya: Mater. & Design 16 (1995) 41.10.1016/0261-3069(95)00006-KSuche in Google Scholar

[7] J.R. Groza, J.C. Gibeling: Mater. Sci. Eng. A 171 (1993) 115.10.1016/0921-5093(93)90398-XSuche in Google Scholar

[8] Y. Zhang, Y.C. Zhou: Z. Metallkd. 91 (2000) 585.10.1006/ndsh.2000.0021Suche in Google Scholar

[9] J.S. Lee, N.J. Kim, J.Y. Jung, Eon-Sik Lee, S. Ahn: Scr. Mater. 39 (1998) 1063.10.1016/S1359-6462(98)00246-2Suche in Google Scholar

[10] Z.Y. Ma, S.C. Tjong: Mater. Sci. Eng. A 284 (2000) 70.10.1016/S0921-5093(00)00797-8Suche in Google Scholar

[11] M.W. Barsoum, G. Yaroschuk, S. Tyagi: Scr. Mater. 37 (1997) 1583.10.1016/S1359-6462(97)00288-1Suche in Google Scholar

[12] M.W. Barsoum, D. Brodkin, T. El-Raghy: Scr. Mater. 36 (1997) 535.10.1016/S1359-6462(96)00418-6Suche in Google Scholar

[13] J.Y. Wu, Y.C. Zhou, C.K. Yan: To be published in Z. Metallkd.Suche in Google Scholar

[14] H.Y. Dong, C.K. Yan, S.Q. Chen, Y.C. Zhou: J. Mater. Chem. 11 (2001) 1402.10.1039/b008973gSuche in Google Scholar

[15] W. Jeitschko, H. Nowotny, F. Benesovsky: Monatsh. Chem. 94 (1963) 672.10.1007/BF00913068Suche in Google Scholar

[16] W. Jeitschko, H. Nowotny, F. Benesovsky: J. Less-Common Metals 7 (1964) 133.10.1016/0022-5088(64)90055-4Suche in Google Scholar

[17] M.W. Barsoum: Prog. Solid St. Chem. 28 (2000) 201.10.1016/S0079-6786(00)00006-6Suche in Google Scholar

[18] Y.C. Zhou, Z.M. Sun: Mater. Res. Innovat. 3 (2000) 286.10.1007/PL00010876Suche in Google Scholar

[19] Y.C. Zhou, W.L. Gu: Z. Metallkd. 95 (2004) 50.10.3139/146.017911Suche in Google Scholar

[20] N. Frage, N. Froumin, M.P. Dariel: Acta Mater. 50 (2002) 237.10.1016/S1359-6454(01)00349-4Suche in Google Scholar

[21] W.B. Pearson: A Handbook of Lattice Spacings and Structures of Metals and Alloys, Pergamon Press, (1958).10.1063/1.3062734Suche in Google Scholar

[22] B.J. Kooi, R.J. Poppen, N.J.M. Carvalho, J.Th. M.De Hosson,M.W. Barsoum: Acta Mater. 51 (2003) 2859.10.1016/S1359-6454(03)00091-0Suche in Google Scholar
Received: 2005-01-28
Accepted: 2005-05-11
Published Online: 2022-02-04

© 2005 Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Frontmatter
  2. Editorial
  3. nanomech 5
  4. Articles Basic
  5. Quantitative evaluation of nanoindents: Do we need more reliable mechanical parameters for the characterization of materials?
  6. Nanoindentation investigation of solid-solution strengthening in III-V semiconductor alloys
  7. Comparison between conventional Vickers hardness and indentation hardness obtained with different instruments
  8. On the pressure dependence of the indentation modulus
  9. A review on the reverse analysis for the extraction of mechanical properties using instrumented Vickers indentation
  10. Articles Applied
  11. Quasi-static and dynamic depth-sensing indentation measurements to characterize wear and mar resistance of coating–polymer systems
  12. Obtaining mechanical parameters for metallisation stress sensor design using nanoindentation
  13. Direct measurement of nanoindentation area function by metrological AFM
  14. A usable concept for the indentation of thin porous films
  15. Analysis of the ductile/brittle transition during a scratch test performed into polymeric film deposited on a PMMA substrate
  16. Nanomechanical and nanotribological properties of polymeric ultrathin films for nanoimprint lithography
  17. Adhesive and nanomechanical properties of polymeric films deposited on silicon
  18. Modelling of the nanoindentation process of ultrathin films
  19. Regular articles
  20. Experimental investigation and thermodynamic calculation in the Al–Be–Si ternary system
  21. Thermodynamic assessment of the Ca–Sn system
  22. Interfacial reaction between Cu and Ti2SnC during processing of Cu–Ti2SnC composite
  23. Effects of heat treatment on the lubricated sliding wear behaviour of zinc-based alloy containing nickel under varying test conditions
  24. Influence of Ce, K, and Na on spheroidization of eutectic carbides in low-tungsten white cast iron
  25. Notifications/Mitteilungen
  26. Personal/Personelles
  27. Press/Presse
https://doi.org/10.1515/ijmr-2005-0229
Schlagwörter für diesen Artikel
Interface; Copper; Ti2SnC; Metal matrix composites

Artikel in diesem Heft

  1. Frontmatter
  2. Editorial
  3. nanomech 5
  4. Articles Basic
  5. Quantitative evaluation of nanoindents: Do we need more reliable mechanical parameters for the characterization of materials?
  6. Nanoindentation investigation of solid-solution strengthening in III-V semiconductor alloys
  7. Comparison between conventional Vickers hardness and indentation hardness obtained with different instruments
  8. On the pressure dependence of the indentation modulus
  9. A review on the reverse analysis for the extraction of mechanical properties using instrumented Vickers indentation
  10. Articles Applied
  11. Quasi-static and dynamic depth-sensing indentation measurements to characterize wear and mar resistance of coating–polymer systems
  12. Obtaining mechanical parameters for metallisation stress sensor design using nanoindentation
  13. Direct measurement of nanoindentation area function by metrological AFM
  14. A usable concept for the indentation of thin porous films
  15. Analysis of the ductile/brittle transition during a scratch test performed into polymeric film deposited on a PMMA substrate
  16. Nanomechanical and nanotribological properties of polymeric ultrathin films for nanoimprint lithography
  17. Adhesive and nanomechanical properties of polymeric films deposited on silicon
  18. Modelling of the nanoindentation process of ultrathin films
  19. Regular articles
  20. Experimental investigation and thermodynamic calculation in the Al–Be–Si ternary system
  21. Thermodynamic assessment of the Ca–Sn system
  22. Interfacial reaction between Cu and Ti2SnC during processing of Cu–Ti2SnC composite
  23. Effects of heat treatment on the lubricated sliding wear behaviour of zinc-based alloy containing nickel under varying test conditions
  24. Influence of Ce, K, and Na on spheroidization of eutectic carbides in low-tungsten white cast iron
  25. Notifications/Mitteilungen
  26. Personal/Personelles
  27. Press/Presse
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 27.10.2025 von https://www.degruyterbrill.com/document/doi/10.1515/ijmr-2005-0229/html
Button zum nach oben scrollen