Home Finite element analysis of the thermo-mechanical fatigue of DD8 single crystal nickel-based superalloy
Article
Licensed
Unlicensed Requires Authentication

Finite element analysis of the thermo-mechanical fatigue of DD8 single crystal nickel-based superalloy

  • L. Zhou EMAIL logo , S. X. Li , Y. C. Wang , Q. S. Zang and K. Lu
Published/Copyright: February 5, 2022
Become an author with De Gruyter Brill
Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 94 Issue 11

Abstract

A nonlinear finite element method is presented for analysing the thermo-mechanical fatigue behavior of the DD8 single crystal nickel-based superalloy. The specimens had axial orientations along the [001] direction. In-phase and out-of-phase thermo-mechanical fatigue were simulated under mechanical strain control with a temperature variation from 450 to 900 °C. The cyclic mechanical behavior, the equivalent stress and plastic strain were investigated in both γ' phase and γ matrix.

Keywords: Finite element analysis; Ni-based superalloys; Thermo-mechanical fatigue
Dr. Li Zhou Shenyang National Laboratory for Materials Science Institute of Metal Research, Chinese Academy of Sciences Shenyang 110016, China Tel.: +86 24 8397 8770 Fax: +86 24 2389 1320

  1. This work was financially supported by the key projects of the National Fundamental Research of China (G 19990650).

References

[1] H. Mughrabi, in: X.R. Wu, Z.G. Wang (Eds.), Proc. 7th Int. Fatigue Congress (FATIGUE'99), Vol. 3 HEP and EMAS (1999) 1967.Search in Google Scholar

[2] Z.G. Wang, Y.B. Xu: Defect Diff. Forum 152 (1997) 1.10.4028/www.scientific.net/DDF.152.1Search in Google Scholar

[3] J. Zrnik, M. Hazlinger, M. Zitnansky, Z.G. Wang: J. Mater. Sci. Tech. 11 (1995) 8.Search in Google Scholar

[4] S. Kraft, H. Mughrabi, in: M.J. Verrilli, M.G. Castelli (Eds.), Proc. Int. Conf. on Thermo-mechanical Fatigue Behavior of Materials ASTM STP 1263, 2 (1996) 27.10.1520/STP16444SSearch in Google Scholar

[5] J.L. Malpert, U. Remy: ASTM STP 942 (1988) 657.Search in Google Scholar

[6] F. Liu, Z.G. Wang, S.H. Ai, Y.C. Wang, X.F. Sun, T. Jin, H.R. Guan: Scripta. Mater. 48 (2003) 1265.10.1016/S1359-6462(03)00051-4Search in Google Scholar

[7] Z.H. Li, S. Schmauder, M. Dong: Comput. Mater. Sci. 15 (1999) 11.10.1016/S0927-0256(99)00014-2Search in Google Scholar

[8] D. Sieborger, H. Knake, U. Glatzel: Mater. Sci. Eng. A 298 (2001) 26.10.1016/S0921-5093(00)01318-6Search in Google Scholar

[9] C. Lall, S. Chin, D.P. Pope: Metall.Trans. A 10 (1979) 1323.10.1007/BF02811988Search in Google Scholar

[10] D. Dye, O. Hunziker, S.M. Roberts, R.C. Reed: Metall. Mater. Trans. A 32 (2001) 1713.10.1007/s11661-001-0149-zSearch in Google Scholar

[11] F. Liu, S.H. Ai, Y.C. Wang, H. Zhang, Z.G. Wang: Int. J. Fatigue 24 (2002) 841.10.1016/S0142-1123(02)00010-5Search in Google Scholar

[12] E. Fleury, L. Remy: Metall. Mater. Trans. A 25 (1994) 99.10.1007/BF02646679Search in Google Scholar

[13] J.L. Malpertu, L. Remy: Metall. Trans. 2 (1990) 389.10.1007/BF02782419Search in Google Scholar

[14] O. Mallet, H. Kaguchi, B. Ilschner, F. Meyer –Olbersleben, K. Nikbin, F. Rezai –Aria, G.A. Webster: Int. J. Fatigue 17 (1995) 129.10.1016/0142-1123(95)95892-KSearch in Google Scholar

[15] O. Mallet, C.C. Engler –Pinto Jr, F. Rezai –Aria: Mater. High Temp. 13 (1995) 47.10.1080/09603409.1995.11689500Search in Google Scholar

[16] S. Kraft, R. Zauter, H. Mughrabi: Fatigue Fract. Eng. Mater. Struct. 16 (1993) 237.10.1111/j.1460-2695.1993.tb00755.xSearch in Google Scholar

[17] E. Fleury, J.S. Ha: Mater. Sci. Technol. 17 (2001) 1079.10.1179/026708301101511211Search in Google Scholar

[18] H.J. Maier, H.J. Christ: Int. J. Fatigue 19 (1997) 267.10.1016/S0142-1123(97)00022-4Search in Google Scholar

[19] H. Ismar, F. Schroter, F. Streicher: Int. J. Solid. Struct. 38 (2001) 127.10.1016/S0020-7683(00)00032-9Search in Google Scholar

[20] L. Zhou, S.X. Li, C.R. Chen, Y.C.Wang, Q.S. Zang, K. Lu: Z. Metallkd. 4 (2002) 315.10.3139/146.020315Search in Google Scholar

[21] L. Zhou, S.X. Li, C.R. Chen, Y.C.Wang, Q.S. Zang, K. Lu: Mater. Sci. Eng. A 352 (2003) 300.10.1016/S0921-5093(02)00901-2Search in Google Scholar
Received: 2003-01-08
Published Online: 2022-02-05

© 2003 Carl Hanser Verlag, München

Articles in the same Issue

  1. Frontmatter
  2. Articles/Aufsätze
  3. Grain boundary diffusion and segregation of Ge in Cu: Radiotracer measurements in different kinetic regimes
  4. Thermal diffusivities of uniaxially cold-pressed Fe2Mo powders
  5. Dislocation structure and crystallite size distribution in plastically deformed Ti determined by X-ray peak profile analysis
  6. Modeling of texture evolution in copper under equal channel angular pressing
  7. Method for in situ texture investigation of recrystallization of Cu and Ti by high-energy synchrotron X-ray diffraction
  8. Contribution of dislocation substructures developed during cold rolling to the formation of rolling textures in Al–Mg alloys
  9. Controlled change in the plastic working conditions of metals in the plane state of strain
  10. Finite element analysis of the thermo-mechanical fatigue of DD8 single crystal nickel-based superalloy
  11. Factors influencing the extent of hydrogen-enhanced brittle cracking in a Cu-strengthened HSLA steel during monotonic loading
  12. Textures and precipitates in Ti-stabilized interstitial-free steel
  13. Coarsening kinetics of Cu particles in an Fe-1.5% Cu alloy
  14. Kinetics of the discontinuous precipitation of a liquid phase in Cu–In alloys
  15. Influence of homogenization on the processing map for hot working of as-cast Mg–2Zn–1Mn alloy
  16. Some characteristics of electrospark deposition
  17. Aktuelle Arbeiten in der Konstitution
  18. Notifications/Mitteilungen
  19. Personal/ Personelles
  20. DGM Events
https://doi.org/10.1515/ijmr-2003-0221
Keywords for this article
Finite element analysis; Ni-based superalloys; Thermo-mechanical fatigue

Articles in the same Issue

  1. Frontmatter
  2. Articles/Aufsätze
  3. Grain boundary diffusion and segregation of Ge in Cu: Radiotracer measurements in different kinetic regimes
  4. Thermal diffusivities of uniaxially cold-pressed Fe2Mo powders
  5. Dislocation structure and crystallite size distribution in plastically deformed Ti determined by X-ray peak profile analysis
  6. Modeling of texture evolution in copper under equal channel angular pressing
  7. Method for in situ texture investigation of recrystallization of Cu and Ti by high-energy synchrotron X-ray diffraction
  8. Contribution of dislocation substructures developed during cold rolling to the formation of rolling textures in Al–Mg alloys
  9. Controlled change in the plastic working conditions of metals in the plane state of strain
  10. Finite element analysis of the thermo-mechanical fatigue of DD8 single crystal nickel-based superalloy
  11. Factors influencing the extent of hydrogen-enhanced brittle cracking in a Cu-strengthened HSLA steel during monotonic loading
  12. Textures and precipitates in Ti-stabilized interstitial-free steel
  13. Coarsening kinetics of Cu particles in an Fe-1.5% Cu alloy
  14. Kinetics of the discontinuous precipitation of a liquid phase in Cu–In alloys
  15. Influence of homogenization on the processing map for hot working of as-cast Mg–2Zn–1Mn alloy
  16. Some characteristics of electrospark deposition
  17. Aktuelle Arbeiten in der Konstitution
  18. Notifications/Mitteilungen
  19. Personal/ Personelles
  20. DGM Events
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 16.9.2025 from https://www.degruyterbrill.com/document/doi/10.1515/ijmr-2003-0221/html
Scroll to top button