Artikel
Open Access
Determination of Flow Stress Using Parametric Linearity Relationship of Arrhenius Power Law
-
Amit Kumar Maheshwari
Veröffentlicht/Copyright:
15. November 2013
Received: 2013-1-23
Accepted: 2013-10-4
Published Online: 2013-11-15
Published in Print: 2014-2-1
©2014 by Walter de Gruyter Berlin/Boston
Artikel in diesem Heft
- Frontmatter
- Creep and Fatigue Behavior in Micro-alloyed Steels – A Review
- Determination of Flow Stress Using Parametric Linearity Relationship of Arrhenius Power Law
- Low-Temperature Sintering of Nanosilver Paste on a Gold Film Surface
- Influence of Interfacial Oxides Formed During Dry Sliding Wear of NiCrBSiCFe Plasma Coating on AISI 316 Steel Substrates
- Tribological Properties of WC-12Co Coating on AZ91 Magnesium Alloy Fabricated by High Velocity Oxy-Fuel Spray
- Heat Treatment Study of γ + α2 Ti Aluminides Obtained through Reaction Synthesis and Hot Deformation
- The Enhanced Thermoelectric Properties of Ba0.4Co4Sb11.7Te0.3 Prepared by the High-Pressure and High-Temperature Method
- Effect of Y and Mg on the Solidification Structure of Fe-36Ni Invar Alloy
- Deformation Mechanisms of Tandem Hot Rolled GH4169 Superalloy during Creep
- Effect of Ce2O3 and CaO/Al2O3 on the Phase, Melting Temperature and Viscosity of CaO-Al2O3-10 Mass% SiO2 Based Slags
- Microstructural Evolution of Aluminum Alloy 2618 During Homogenization and Its Kinetic Analysis
- Synthesis and Characterization of New Poly(amide-imide)/organoclay Nanocomposites Derived from N,N′-(4,4′-diphtaloyl)-bis-L-α-aminophenyl Acetic Diacid and 1,2-Bis(4-aminophenoxy)ethane
Schlagwörter für diesen Artikel
material modeling;
viscoplastic flow;
strain;
strain rate;
thermomechanical processing
Creative Commons
BY-NC-ND 3.0
Artikel in diesem Heft
- Frontmatter
- Creep and Fatigue Behavior in Micro-alloyed Steels – A Review
- Determination of Flow Stress Using Parametric Linearity Relationship of Arrhenius Power Law
- Low-Temperature Sintering of Nanosilver Paste on a Gold Film Surface
- Influence of Interfacial Oxides Formed During Dry Sliding Wear of NiCrBSiCFe Plasma Coating on AISI 316 Steel Substrates
- Tribological Properties of WC-12Co Coating on AZ91 Magnesium Alloy Fabricated by High Velocity Oxy-Fuel Spray
- Heat Treatment Study of γ + α2 Ti Aluminides Obtained through Reaction Synthesis and Hot Deformation
- The Enhanced Thermoelectric Properties of Ba0.4Co4Sb11.7Te0.3 Prepared by the High-Pressure and High-Temperature Method
- Effect of Y and Mg on the Solidification Structure of Fe-36Ni Invar Alloy
- Deformation Mechanisms of Tandem Hot Rolled GH4169 Superalloy during Creep
- Effect of Ce2O3 and CaO/Al2O3 on the Phase, Melting Temperature and Viscosity of CaO-Al2O3-10 Mass% SiO2 Based Slags
- Microstructural Evolution of Aluminum Alloy 2618 During Homogenization and Its Kinetic Analysis
- Synthesis and Characterization of New Poly(amide-imide)/organoclay Nanocomposites Derived from N,N′-(4,4′-diphtaloyl)-bis-L-α-aminophenyl Acetic Diacid and 1,2-Bis(4-aminophenoxy)ethane
