Home Experimental evaluation of forming limit diagram and mechanical properties of nano/ultra-fine grained aluminum strips fabricated by accumulative roll bonding
Article
Licensed
Unlicensed Requires Authentication

Experimental evaluation of forming limit diagram and mechanical properties of nano/ultra-fine grained aluminum strips fabricated by accumulative roll bonding

  • Davood Rahmatabadi and Ramin Hashemi
Published/Copyright: November 25, 2017
Become an author with De Gruyter Brill
Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 108 Issue 12

Abstract

In this research, for the first time, forming limit diagrams (FLDs) of ultra-fine grained Al/Al samples produced by accumulative roll bonding (ARB) process were evaluated. The samples were successfully prepared through ARB up to the 7th pass. Mechanical properties, tensile fracture surfaces, and crystallite size of samples were investigated. The level of the FLD and elongation at first decreased and then increased, continuously. The results of tensile testing revealed that by increasing the number of ARB passes, the tensile strength increased continuously. Microhardness of Al strips increased and reached a value of 51 VHN after the seventh pass. Results of X-ray diffraction demonstrated that crystallite size decreased from 1 341 nm for annealed condition and it reached to 175 nm for ARBed samples after the 7th pass. SEM images showed that the fracture mode in the ARBed samples was a shear ductile fracture with elongated sophomoric shear dimples.

Keywords: Forming limit diagrams; Accumulative roll bonding; Mechanical properties; SEM; AA1050
*Correspondence address, Dr Ramin Hashemi, Assistant professor, School of Mechanical Engineering, Iran University of Science and Technology, Tehran 16844, Iran, Tel.: +98-21-77240068, Fax: +98-21-77240540, E-mail:

References

[1] J.Evancho, J.Kaufman: SAE Technical Paper. 1977.10.4271/770307Search in Google Scholar

[2] L.Troeger, E.Starke: Mater. Sci. Eng. A277 (2000) 102. 10.1016/S0921-5093(99)00543-2Search in Google Scholar

[3] S.Lee, Y.Saito, T.Sakai, H.Utsunomiya: Mater. Sci. Eng. A325 (2002) 228. 10.1016/S0921-5093(01)01416-2Search in Google Scholar

[4] R.Jamaati, M.R.Toroghinejad: Mater. Des.31 (2010) 4816. 10.1016/j.matdes.2010.04.048Search in Google Scholar

[5] M.Raei, M.R.Toroghinejad, R.Jamaati: Mater. Manuf. Pro.26 (2011) 1352. 10.1080/10426914.2011.557133Search in Google Scholar

[6] H.Pirgazi, A.Akbarzadeh, R.Petrov, L.Kestens: Mater. Sci. Eng. A497 (2008) 132. 10.1016/j.msea.2008.06.025Search in Google Scholar

[7] M.R.Toroghinejad, F.Ashrafizadeh, R.Jamaati: Mater. Sci. Eng. A561 (2013) 145. 10.1016/j.msea.2012.11.010Search in Google Scholar

[8] R.Z.Valiev, T.G.Langdon: Prog. Mater. Sci.51 (2006) 881. 10.1016/j.pmatsci.2006.02.003Search in Google Scholar

[9] R.Z.Valiev, N.Krasilnikov, N.Tsenev: Mater. Sci. Eng. A137 (1991) 35. 10.1016/0921-5093(91)90316-FSearch in Google Scholar

[10] V.Segal: Mater. Sci. Eng. A197 (1995) 157. 10.1016/0921-5093(95)09705-8Search in Google Scholar

[11] M.Furukawa, Y.Iwahashi, Z.Horita, M.Nemoto, T.G.Langdon: Mater. Sci. Eng. A257 (1998) 328. 10.1016/S0921-5093(98)00750-3Search in Google Scholar

[12] G.Sakai, Z.Horita, T.G.Langdon: Mater. Sci. Eng. A393 (2005) 344. 10.1016/j.msea.2004.11.007Search in Google Scholar

[13] A.P.Zhilyaev, T.G.Langdon: Prog. Mater. Sci.53 (2008) 893. 10.1016/j.pmatsci.2008.03.002Search in Google Scholar

[14] Z.Horita, D.J.Smith, M.Furukawa, M.Nemoto, R.Z.Valiev, T.G.Langdon: J. Mater. Res.11 (1996) 1880. 10.1557/JMR.1996.0239Search in Google Scholar

[15] M.Richert, H.Stüwe, J.Richert, R.Pippan, C.Motz: Mater. Sci. Eng. A.301 (2001) 237. 10.1016/S0921-5093(00)01803-7Search in Google Scholar

[16] J.Yin, J.Lu, H.Ma, P.Zhang: J. Mater. Sci.39 (2004) 2851. 10.1023/B:JMSC.0000021463.83899.b3Search in Google Scholar

[17] D.H.Shin, J.-J.Park, Y.-S.Kim, K.-T.Park: Mater. Sci. Eng. A328 (2002) 98.10.1016/S0921-5093(01)01665-3Search in Google Scholar

[18] Y.Saito, H.Utsunomiya, N.Tsuji, T.Sakai: Acta. Mater.47 (1999) 579. 10.1016/S1359-6454(98)00365-6Search in Google Scholar

[19] N.Tsuji, Y.Saito, S.H.Lee, Y.Minamino: Adv. Eng. Mater.5 (2003) 338. 10.1002/adem.200310077Search in Google Scholar

[20] X.Huang, N.Tsuji, N.Hansen, Y.Minamino: Mater. Sci. Eng. A340 (2003) 265.10.1016/S0921-5093(02)00182-XSearch in Google Scholar

[21] M.R.Rezaei, M.R.Toroghinejad, F.Ashrafizadeh: Mater. Sci. Eng. A529 (2011) 442. 10.1016/j.msea.2011.09.057Search in Google Scholar

[22] P.Hsieh, Y.Hung, J.Huang: Scr. Mater.49 (2003) 173. 10.1016/S1359-6462(03)00207-0Search in Google Scholar

[23] M.Shaarbaf, M.R.Toroghinejad: Mater. Sci. Eng. A473 (2008) 28. 10.1016/j.msea.2007.03.065Search in Google Scholar

[24] S.Pasebani, M.R.Toroghinejad: Mater. Sci. Eng. A527 (2010) 491. 10.1016/j.msea.2009.09.029Search in Google Scholar

[25] D.Terada, S.Inoue, N.Tsuji: J. Mater. Sci.42 (2007) 1673. 10.1007/s10853-006-0909-7Search in Google Scholar

[26] M.Zhan, Y.Li, W.Chen, W.Chen: J. Mater. Sci.42 (2007) 9256. 10.1007/s10853-007-1885-2Search in Google Scholar

[27] N.Tsuji, R.Ueji, Y.Minamino: Scr. Mater.47 (2002) 69. 10.1016/S1359-6462(02)00088-XSearch in Google Scholar

[28] D.Yang, P.Cizek, P.Hodgson, C.e.Wen: Scr. Mater.62 (2010) 321. 10.1016/j.scriptamat.2009.11.036Search in Google Scholar

[29] S.P.Keeler: SAE Technical Paper. 1965.10.4271/650535Search in Google Scholar

[30] R.Hashemi, H.Mamusi, A.Masoumi: Proceedings of the Institution of Mechanical Engineers, Part B: J. Eng. Manuf. (2014).10.1177/0954405414522448Search in Google Scholar

[31] C.Zhang, L.Leotoing, D.Guines, E.Ragneau: J. Mater. Pro. Technol.209 (2009) 3849. 10.1016/j.jmatprotec.2008.09.003Search in Google Scholar

[32] C.Zhang, X.Chu, D.Guines, L.Leotoing, J.Ding, G.Zhao: Mater. Des.67 (2015) 522. 10.1016/j.matdes.2014.10.074Search in Google Scholar

[33] A.Rezaee-Bazzaz, H.Noori, R.Mahmudi: Int. J. Mech. Sci.53 (2011) 262. 10.1016/j.ijmecsci.2011.01.007Search in Google Scholar

[34] F.Zhang, J.Chen, J.Chen, X.Zhu: Int. J. Mech. Sci.89 (2014) 40. 10.1016/j.ijmecsci.2014.08.016Search in Google Scholar

[35] K.Wang, J.E.Carsley, L.Zhang, T.B.Stoughton, J.Li, B.E.Carlson: Int. J. Mech. Sci.82 (2014) 13. 10.1016/j.ijmecsci.2014.02.025Search in Google Scholar

[36] N.B.K.Babu, M.Davidson, A.N.Rao, K.Balasubramanian, M.Govindaraju: Mater. Design.55 (2014) 35. 10.1016/j.matdes.2013.10.004Search in Google Scholar

[37] W.Lee, X.Wen: Int. J. Mech. Sci.48 (2006) 134. 10.1016/j.ijmecsci.2005.08.005Search in Google Scholar

[38] E.Karajibani, R.Hashemi, M.Sedighi: Int. J. Adv. Manuf. Technol.90 (2017) 2713. 10.1007/s00170-016-9585-1Search in Google Scholar

[39] M.Nurcheshmeh, D.E.Green: Int. J. Mech. Sci.53 (2011) 145. 10.1016/j.ijmecsci.2010.12.004Search in Google Scholar

[40] A.Assempour, R.Hashemi, K.Abrinia, M.Ganjiani, E.Masoumi: Comput. Mater. Sci.45 (2009) 195. 10.1016/j.commatsci.2008.09.025Search in Google Scholar

[41] O.Yigit: Int. J. Adv. Manuf. Technol.67 (2013) 2689. 10.1007/s00170-012-4684-0Search in Google Scholar

[42] K.Ito, K.Satoh, M.Goya, T.Yoshida: Int. J. Mech. Sci.42 (2000) 2233. 10.1016/S0020-7403(00)00004-7Search in Google Scholar

[43] H.Rahimi, M.Sedighi, R.Hashemi: Part L: J. Mater. Des. Appl. (2016).10.1177/1464420716655560Search in Google Scholar

[44] R.Lapovok, I.Timokhina, P.McKenzie, R.O'Donnell: J. Mater. Pro. Technol.200 (2008) 441. 10.1016/j.jmatprotec.2007.08.083Search in Google Scholar

[45] R.Hashemi, G.Faraji, K.Abrinia, A.F.Dizaji: Int. J. Adv. Manuf. Technol.46 (2010) 551. 10.1007/s00170-009-2121-9Search in Google Scholar

[46] F.Ozturk, D.Lee: Journal of Materials Processing Technology. J. Mater. Pro. Technol.170 (2005) 247. 10.1016/j.jmatprotec.2005.05.010Search in Google Scholar

[47] D.Hughes, N.Hansen: Acta. Mater.45 (1997) 3871. 10.1016/S1359-6454(97)00027-XSearch in Google Scholar

[48] M.Naseri, A.Hassani, M.Tajally: Cer. Int.41 (2015) 3952. 10.1016/j.ceramint.2014.11.079Search in Google Scholar

[49] L.Ceschini, G.Minak, A.Morri: Comp. Sci. Technol.66 (2006) 333. 10.1016/j.compscitech.2005.04.044Search in Google Scholar

[50] A.Shabani, M.R.Toroghinejad, A.Shafyei: Mater. Sci. Eng.A558 (2012) 386.10.1016/j.msea.2012.08.017Search in Google Scholar

[51] M.Reihanian, F.K.Hadadian, M.Paydar: Mater. Sci. Eng. A607 (2014) 188. 10.1016/j.msea.2014.04.013Search in Google Scholar

[52] M.Alizadeh, M.Samiei: Mater. Des.56 (2014) 680. 10.1016/j.matdes.2013.11.067Search in Google Scholar

[53] N.Hansen, X.Huang, R.Ueji, N.Tsuji: Mater. Sci. Eng. A387 (2004) 191. 10.1016/j.msea.2004.02.078Search in Google Scholar

[54] Y.Wang, E.Ma: Acta. Mater.52 (2004) 1699. 10.1016/j.actamat.2003.12.022Search in Google Scholar

[55] N.Tsuji, Y.Ito, Y.Saito, Y.Minamino: Scr. Mater.47 (2002) 893. 10.1016/S1359-6462(02)00282-8Search in Google Scholar

[56] L.Su, C.Lu, H.Li, G.Deng, K.Tieu: Mater. Sci. Eng. A614 (2014) 148. 10.1016/j.msea.2014.07.032Search in Google Scholar

[57] M.Alizadeh, M.Paydar, F.S.Jazi: Comp. Part B: Eng.44 (2013) 339. 10.1016/j.compositesb.2012.04.069Search in Google Scholar

[58] S.O.Gashti, A.Fattah-alhosseini, Y.Mazaheri, M.K.Keshavarz: J. Alloy. Compound.688, Part B (2016) 44. 10.1016/j.jallcom.2016.07.177Search in Google Scholar

[59] M.Sedighi, M.H.Vini, P.Farhadipour: Powder. Metal. Cer.55 (2016) 413. 10.1007/s11106-016-9821-0Search in Google Scholar

[60] M.H.Vini, M.Sedighi, M.Mondali: Int. J. Mater. Res.108 (2017) 53. 10.3139/146.111450Search in Google Scholar

Received: 2017-02-17
Accepted: 2017-08-08
Published Online: 2017-11-25
Published in Print: 2017-12-08

© 2017, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. First principles, thermal stability and thermodynamic assessment of the binary Ni–W system
  5. Experimental evaluation of forming limit diagram and mechanical properties of nano/ultra-fine grained aluminum strips fabricated by accumulative roll bonding
  6. FSW of bimodal reinforced Al-based composites produced via spark plasma sintering
  7. Modelling analysis and experiments of polycrystalline silicon directional solidification in an annular heating field
  8. Effect of flow, heat transfer and magnetic energy on the grain refinement of 7A04 alloy under electromagnetic pulse
  9. A study on effects of a new two-step strain induced melt activation process on characteristics of Al 7075 alloy
  10. Synthesis and characterization of mechanically alloyed cerium oxide reinforced Al-4.5Mg alloy composite
  11. Densification rate and interfacial adhesion of bilayer cemented tungsten carbide and steel
  12. Short Communications
  13. Cavitation erosion of 17-4 PH stainless steels following sub-zero treatment
  14. Investigation on microstructure and thermal properties of in-situ synthesized Cu–ZrO2 nanocomposites
  15. DGM News
  16. DGM News
https://doi.org/10.3139/146.111566
Keywords for this article
Forming limit diagrams; Accumulative roll bonding; Mechanical properties; SEM; AA1050

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. First principles, thermal stability and thermodynamic assessment of the binary Ni–W system
  5. Experimental evaluation of forming limit diagram and mechanical properties of nano/ultra-fine grained aluminum strips fabricated by accumulative roll bonding
  6. FSW of bimodal reinforced Al-based composites produced via spark plasma sintering
  7. Modelling analysis and experiments of polycrystalline silicon directional solidification in an annular heating field
  8. Effect of flow, heat transfer and magnetic energy on the grain refinement of 7A04 alloy under electromagnetic pulse
  9. A study on effects of a new two-step strain induced melt activation process on characteristics of Al 7075 alloy
  10. Synthesis and characterization of mechanically alloyed cerium oxide reinforced Al-4.5Mg alloy composite
  11. Densification rate and interfacial adhesion of bilayer cemented tungsten carbide and steel
  12. Short Communications
  13. Cavitation erosion of 17-4 PH stainless steels following sub-zero treatment
  14. Investigation on microstructure and thermal properties of in-situ synthesized Cu–ZrO2 nanocomposites
  15. DGM News
  16. DGM News
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 16.11.2025 from https://www.degruyterbrill.com/document/doi/10.3139/146.111566/pdf
Scroll to top button