Hardfacing behavior of Cr–Ni stainless steel with Co-based super alloys
-
Mustafa Nursoy
Abstract
In this study, the hardfacing behavior of Cr – Ni stainless steel was studied by depositing of Stellite 1, Stellite 6, and Stellite 12 superalloys on Cr – Ni stainless steel specimens using electric arc welding and tungsten inert gas welding. The cobalt base alloys were hardfaced on stainless steel plates as a single layer. The samples taken from the hardfaced materials were studied by optical microscopy, scanning electron microscopy, X-ray diffraction, and microhardness measurements. The hardness and wear resistance values of the layer obtained after the hardfacing processes are satisfactory and the process seem to be suitable for application.
References
[1] H.Çelik: High Temperature Wear Behaviors of Weldable Co- and Fe-based alloys. Istanbul Technical Unv, Ph.D. Thesis, 1991.Suche in Google Scholar
[2] H.ÇelikH.Çimenoğlu, E.S.Kayali: Abrasive Wear Propertirs of Some Stellite Alloys, European Joint Conf on Engineering Systems Design and Analysis (1992) 361–365.Suche in Google Scholar
[3] P.J.Hofmann, B.C.Fiedrich, in: H.Ocken (Ed.), Laboratory Evaluations of Iron-Based Hardfacing Alloys, Electric Power Research Institute (1988).Suche in Google Scholar
[4] K.P.Cooper: Laser Surface Processing, Friction, Lubrication, and Wear Technology, v 18, ASM Handbook (1992).Suche in Google Scholar
[5] M.İzcilerH.Çelik: J. Mater. Process. Technol.105 (2000) 237–245.10.1016/S0924-0136(00)00550-1Suche in Google Scholar
[6] H.E.Placko, A.Stanley, H.J.Payer: J. Biomed. Mater. Res.52 (1998) 292–299.10.1002/(SICI)1097-4636(199802)39:2<292::AID-JBM17>3.0.CO;2-FSuche in Google Scholar
[7] L.Mingxi, H.Yizhu, Y.Xiaomin: Surf. Sci.252 (2005) 2882–2887.10.1016/j.apsusc.2005.04.038Suche in Google Scholar
[8] J.C.Fang, W.J.Xu, Z.Y.Zhao, H.P.Zeng: Surf. Coat. Technol.201 (2007) 5671–5675.10.1016/j.surfcoat.2006.07.055Suche in Google Scholar
[9] K.M.Kulkarni, V.Anand: Metal Powders Used for Hardfacing, Powder Metallurgy, ASM Handbook (1984).Suche in Google Scholar
[10] K.Y.Lee, G.G.Kim, J.H.Kim, S.H.Lee, S.J.Kim: Wear262 (2007) 845–849.10.1016/j.wear.2006.08.015Suche in Google Scholar
[11] M.X.Yao, J.B.C.Wu, Y.Xie: Mater. Sci. Eng. A407 (2005) 234–244.10.1016/j.msea.2005.06.062Suche in Google Scholar
[12] W.Schwarz, H.Warlimont: Mater. Sci. Eng. A226 (1997) 1098–1101.10.1016/S0921-5093(96)10867-4Suche in Google Scholar
[13] V.Kuzucu, M.Ceylan, H.Çelik, I.Aksoy: J. Mater. Process. Technol.74 (1998) 137–141.10.1016/S0924-0136(97)00261-6Suche in Google Scholar
© 2008, Carl Hanser Verlag, München
Artikel in diesem Heft
- Contents
- Contents
- Basic
- A model to calculate the viscosity of silicate melts
- A model to calculate the viscosity of silicate melts
- A note on the application of the phase rule
- Thermodynamic properties of liquid silver–indium–tin alloys determined from emf measurements
- Unconstrained solidification and characterisation of near-eutectic Al–Cu–Ag alloys
- Tensile properties of L12 intermetallic foils fabricated by cold rolling
- Microstructural control of FeB-inoculated mottled low-alloy white iron by a design of experiments approach
- Applied
- Dislocation structure and crystallite size distribution in lath martensite determined by X-ray diffraction peak profile analysis
- Effect of minor addition of Pb upon interfacial reactions and mechanical properties at Sn-3.0Ag-0.5Cu/Cu and Sn-58Bi/Cu solder joints
- Elastic properties of braided ceramic matrix composites
- The influence of microstructural characteristics and contaminants on the mechanical properties and fracture topography of low cost Ti6Al4V alloy
- Microstructure and room temperature mechanical properties of Hf and Sn-doped Nb-20Ti-5Cr-3Al-18Si alloy
- The effect of alloying elements on constrained carbon equilibrium due to a quench and partition process
- Hardfacing behavior of Cr–Ni stainless steel with Co-based super alloys
- Development of SMD 32.768 kHz tuning fork-type crystals
- Notification
- DGM News
Artikel in diesem Heft
- Contents
- Contents
- Basic
- A model to calculate the viscosity of silicate melts
- A model to calculate the viscosity of silicate melts
- A note on the application of the phase rule
- Thermodynamic properties of liquid silver–indium–tin alloys determined from emf measurements
- Unconstrained solidification and characterisation of near-eutectic Al–Cu–Ag alloys
- Tensile properties of L12 intermetallic foils fabricated by cold rolling
- Microstructural control of FeB-inoculated mottled low-alloy white iron by a design of experiments approach
- Applied
- Dislocation structure and crystallite size distribution in lath martensite determined by X-ray diffraction peak profile analysis
- Effect of minor addition of Pb upon interfacial reactions and mechanical properties at Sn-3.0Ag-0.5Cu/Cu and Sn-58Bi/Cu solder joints
- Elastic properties of braided ceramic matrix composites
- The influence of microstructural characteristics and contaminants on the mechanical properties and fracture topography of low cost Ti6Al4V alloy
- Microstructure and room temperature mechanical properties of Hf and Sn-doped Nb-20Ti-5Cr-3Al-18Si alloy
- The effect of alloying elements on constrained carbon equilibrium due to a quench and partition process
- Hardfacing behavior of Cr–Ni stainless steel with Co-based super alloys
- Development of SMD 32.768 kHz tuning fork-type crystals
- Notification
- DGM News
