Startseite Cyclic deformation behavior of deep rolled as-quenched aluminium alloy AA6110 at elevated temperatures
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Cyclic deformation behavior of deep rolled as-quenched aluminium alloy AA6110 at elevated temperatures

  • Patiphan Juijerm und Igor Altenberger
Veröffentlicht/Copyright: 23. Mai 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 98 Heft 6

Abstract

The as-quenched (solution-heat-treated) aluminium wrought alloy AA6110 (Al – Mg – Si – Cu) was mechanically surface treated (deep rolled) at room temperature. The deep rolled as-quenched AA6110 was cyclically deformed at room and elevated temperatures up to 250 °C using stress-controlled push-pull fatigue tests. Cyclic deformation behavior and Wöhler curves of the deep rolled as-quenched AA6110 have been investigated and compared to the polished condition as a reference. The effect of static/dynamic precipitation occurring during fatigue at elevated temperatures was analyzed and discussed. The stability of residual stresses as well as work hardening at elevated temperature was investigated using X-ray diffraction methods. Finally, from the S/N data, a borderline describing the effectiveness of deep rolling for different loading combinations in a stress amplitude – temperature diagram was established.

Keywords: High-temperature fatigue; Deep rolling; Residual stress relaxation; Work hardening; Aluminium alloy
* Correspondence address, Dr.-Ing. Patiphan Juijerm, Kasetsart University, Department of Materials Engineering, 50 Phaholyothin Rd., Jatujak, Bankok 10900, Thailand, Tel.: +662 942 8555, Fax: +662 955 1811, E-mail:

References

[1] I.J.Polmear: Light Alloys, Metallurgy of Light Metals, Halsted Press, London, 1996.Suche in Google Scholar

[2] C.Barbosa, J.M.A.Rebello, O.Acselrad, J.Dille, J.-L.Delplancke: Z. Metallkd.93 (2002) 3.Suche in Google Scholar

[3] E.Zschech: HTM51 (1996) 3.10.1515/htm-1996-510303Suche in Google Scholar

[4] A.Niku-Lari (Ed.): Advances in Surface Treatments, Pergamon Press, Oxford (1987).Suche in Google Scholar

[5] B.Scholtes, in: V.Hauk (Ed.), Structural and Residual Stress Analysis by Nondestructive Methods, Elsevier, Amsterdam (1997) 590.10.1016/B978-044482476-9/50020-7Suche in Google Scholar

[6] L.Wagner: Mater. Sci. Eng. A263 (1999) 210.10.1016/S0921-5093(98)01168-XSuche in Google Scholar

[7] I.Altenberger, in: V.Schulze, A.Niku-Lari (Eds.), Shot Peening and other Mechanical Surface Treatments, IITT-International, Marne la Vallee (2005) 144.Suche in Google Scholar

[8] D.Löhe, O.Vöhringer, in: G. Totten, M. Howes, T. Inoue (Eds.), ASM International Handbook of Residual stress and Deformation of Steel (2002).Suche in Google Scholar

[9] P.Juijerm, U.Noster, I.Altenberger, B.Scholtes: Mater. Sci. Eng. A379 (2004) 286.10.1016/j.msea.2004.02.022Suche in Google Scholar

[10] P.Juijerm, I.Altenberger, U.Noster, B.Scholtes: Mater. Sci. Forum, vol.490 (2005) 436.10.4028/www.scientific.net/MSF.490-491.436Suche in Google Scholar

[11] P.Juijerm, I.Altenberger: Mater. Sci. Eng. A 452–453 /2007) 475.10.1016/j.msea.2006.10.074Suche in Google Scholar

[12] P.Juijerm, I.Altenberger: Scripta Mater.55 (2006) 943.10.1016/j.scriptamat.2006.07.030Suche in Google Scholar

[13] P.Juijerm, I.Altenberger: Scripta Mater.55 (2006) 1111.10.1016/j.scriptamat.2006.08.047Suche in Google Scholar

[14] P.Juijerm, I.Altenberger, B.Scholtes: Mater. Sci. Eng A426 (2006) 4.10.1016/j.msea.2005.11.064Suche in Google Scholar

[15] P.Juijerm, I.Altenberger, B.Scholtes: Int. J. Fatigue29 (2007) 1374.10.1016/j.ijfatigue.2006.10.008Suche in Google Scholar

[16] S.Suresh: Fatigue of Materials, Cambridge university press, Cambridge (2003).Suche in Google Scholar

[17] J.Kohout: Fatigue Fract. Eng. Mater. Struct.23 (2000) 969.10.1046/j.1460-2695.2000.00276.xSuche in Google Scholar

[18] T.S.Srivatsan, E. J.CoyneJr: Int. J. Fatigue8 (1986) 201.10.1016/0142-1123(86)90022-8Suche in Google Scholar

[19] T.S.Srivatsan: Int. J. Fatigue13 (1991) 313.10.1016/0142-1123(91)90358-6Suche in Google Scholar

Received: 2006-10-9
Accepted: 2007-1-24
Published Online: 2013-05-23
Published in Print: 2007-06-01

© 2007, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Basic
  4. The effect of bismuth segregation on the faceting of Σ3 and Σ9 coincidence boundaries in copper bicrystals
  5. Viscosity measurement of liquid ternary Cu–Ni–Fe alloys by an oscillating cup viscometer and comparison with models
  6. Isothermal oxidation behavior of a precipitation-hardened Pt-base alloy with additions of Al, Cr and Ni
  7. Bismuth activity measurements and thermodynamic re-optimization of the Ni–Bi System
  8. Modelling of the β → α + β transformation in a metastable β Ti alloy based on the growth kinetics and the morphology of the α plates
  9. The microstructure of ball milled nanocrystalline vanadium; variation of the crystal imperfection and the lattice parameter
  10. Study of interfacial reactions between Sn–Ag–Cu alloys and Au substrate
  11. Applied
  12. On the precipitation processes in commercial QE22 magnesium alloy
  13. Cyclic deformation behavior of deep rolled as-quenched aluminium alloy AA6110 at elevated temperatures
  14. Effect of Ho additions on the microstructure and mechanical properties of Nb-22Ti-16Si-7Cr-3Al-3Ta-2Hf alloys
  15. Improved mechanical properties of the high pressure die casting alloy AlSi9Cu3(Fe)(Zn) as a result of the combination of natural and artificial ageing
  16. Effect of quenching temperature on the microstructure and mechanical properties of Fe–B–Ti alloy
  17. A kinetic study of nickel coating on boron nitride micro-particles
  18. Thermal diffusivity measurements of some industrially important alloys by a laser flash method
  19. Notifications
  20. DGM News
https://doi.org/10.3139/146.101496
Schlagwörter für diesen Artikel
High-temperature fatigue; Deep rolling; Residual stress relaxation; Work hardening; Aluminium alloy

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Basic
  4. The effect of bismuth segregation on the faceting of Σ3 and Σ9 coincidence boundaries in copper bicrystals
  5. Viscosity measurement of liquid ternary Cu–Ni–Fe alloys by an oscillating cup viscometer and comparison with models
  6. Isothermal oxidation behavior of a precipitation-hardened Pt-base alloy with additions of Al, Cr and Ni
  7. Bismuth activity measurements and thermodynamic re-optimization of the Ni–Bi System
  8. Modelling of the β → α + β transformation in a metastable β Ti alloy based on the growth kinetics and the morphology of the α plates
  9. The microstructure of ball milled nanocrystalline vanadium; variation of the crystal imperfection and the lattice parameter
  10. Study of interfacial reactions between Sn–Ag–Cu alloys and Au substrate
  11. Applied
  12. On the precipitation processes in commercial QE22 magnesium alloy
  13. Cyclic deformation behavior of deep rolled as-quenched aluminium alloy AA6110 at elevated temperatures
  14. Effect of Ho additions on the microstructure and mechanical properties of Nb-22Ti-16Si-7Cr-3Al-3Ta-2Hf alloys
  15. Improved mechanical properties of the high pressure die casting alloy AlSi9Cu3(Fe)(Zn) as a result of the combination of natural and artificial ageing
  16. Effect of quenching temperature on the microstructure and mechanical properties of Fe–B–Ti alloy
  17. A kinetic study of nickel coating on boron nitride micro-particles
  18. Thermal diffusivity measurements of some industrially important alloys by a laser flash method
  19. Notifications
  20. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 16.10.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.101496/html
Button zum nach oben scrollen