Home Technology The Effect of Sputter Cleaning and TiN Coating after Sputter Cleaning on Tensile and Fatigue Behavior of a Nodular Cast Iron
Article
Licensed
Unlicensed Requires Authentication

The Effect of Sputter Cleaning and TiN Coating after Sputter Cleaning on Tensile and Fatigue Behavior of a Nodular Cast Iron

  • , and EMAIL logo
Published/Copyright: January 8, 2022
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 92 Issue 6

Abstract

In this study, the effect of sputter cleaning and TiN coating after sputter cleaning on tensile and fatigue behaviour of GGG 40 grade nodular cast iron was studied. It was found that sputter cleaning and TiN coating after sputter cleaning by arc physical vapour deposition technique improved the static and dynamic strength properties (tensile strength and endurance limit) of GGG 40 grade nodular cast iron material at the same amount and these properties were increased about 20 MPa. From this result, it is concluded that TiN coating did not cause a further increase in these properties after sputter cleaning.

Keywords: Endurance limit; Fatigue strength; Arc PVD technique; Sputter cleaning; TiN coating
Prof. E. Sabri Kayal <i Department of Metallurgical and Material Engineering 80626 Maslak, Istanbul, Turkey Fax: +90 212 2853427

  1. The authors gratefully acknowledge the support of NATO TU PVD Coatings Project for the equipment supplied to the Metallurgical and Material Engineering Department of Istanbul Technical University, which was utilized in this study. The authors would like to thank especially Prof. M. Ürgen and Mr O. L. Eryilmaz for kindly supplying coating treatment of the specimens.

References

1 Dieter, G.: Mechanical Metallurgy, McGraw Hill, London (1988).Search in Google Scholar

2 Shiozawa, K., in: M.H. Alibadi; C.A. Brebbia (eds.), Proc. Conf. on Computational Mechanics, Boston, MA (1997) 227.Search in Google Scholar

3 Bhushan, B.; Gupta, B.K.: Handbook of Tribology, McGraw Hill, (1991).Search in Google Scholar

4 Shiozawa, K.; Motobayashi, K.; Sonobe, M.: J. Soc. Mater. Sci. Jpn. 45 (1996) 26.10.2472/jsms.45.26Search in Google Scholar

5 Herr, W.; Matthes, B.; Broszeit, E.; Kloos, K.H.: Surf. Coat. Technol. 57 (1993) 43.10.1016/0257-8972(93)90334-KSearch in Google Scholar

6 Ferreira, J.A.M.; Borrego, L.F.P.; Costa, J.D.M.: Fatigue Fract. Eng. Mater. & Struct. 19 (1996) 111.10.1111/j.1460-2695.1996.tb00936.xSearch in Google Scholar

7 Shiozawa, K.; Nishino, S.; Handa, K.: JSME Series I, 35 (1992) 347.Search in Google Scholar

8 Ferreira, J.A.M.; Costa, J.D.M.; Lapa, V.: Int. J. Fatigue 119 (1997) 293.10.1016/S0142-1123(97)00007-8Search in Google Scholar

9 Shiozawa, K.; Tomosaka, T.; Han, L.; Motobayashi, K.: JSME Int. J., Series A 39 (1996) 142.Search in Google Scholar

10 Hotta, S.; Itou, Y.; Saruki, K.; Arai, T.; Surf. Coat. Technol. 73 (1995) 5.10.1016/0257-8972(94)02356-5Search in Google Scholar

11 Shiozawa, K.; Motabayashi, K.; Sonobe, M., in: M.H. Alibadi; C.A. Brebbia (eds.), Proc. Conf. on Computational Mechanics, Boston, MA (1995) 147.Search in Google Scholar

12 Sonobe, M.; Shiozawa, K.; Motobayashi, K., in: M.H. Alibadi; C.A. Brebbia (eds.), Proc. Conf. on Computational Mechanics, Boston, MA (1996) 615.Search in Google Scholar

13 Sonobe, M.; Shiozawa, K.: J. Soc. Mater. Sci. Jpn. 46 (1997) 1070.10.2472/jsms.46.1070Search in Google Scholar

14 Lunarska, E.: Mater. Corrosion 48 (1997) 101.10.1002/maco.19970480205Search in Google Scholar

15 Su, Y.L.; Yao, S.H.; Wei, W.H.; Wu, C.T.: Mater. Sci. Technol. 15 (1999) 73.10.1179/026708399773002845Search in Google Scholar

16 Shiozawa, K.; Ohshima, S., in: H. Kitagawa, T. Tanaka (eds.), Proc. 4th Int. Conf. on Fatigue and Fatigue Thresholds, Honolulu, HI (1990) 299.Search in Google Scholar

17 Su, Y.L.; Yao, S. H.; Wei, W.H.; Wu, C.T.: Thin Solid Films 315 (1998) 153.10.1016/S0040-6090(97)00707-4Search in Google Scholar

18 Su, Y.L.; Yao, S.H.; Wei, W.H.; Wu, C.T.: Thin Solid Films 322 (1998) 218.10.1016/S0040-6090(97)01013-4Search in Google Scholar

19 Bas¸man, G.: Master Thesis, Technical University, Istanbul (1998).Search in Google Scholar

20 ASTM E 739-91: Standard Practice for Statistical Analysis of Linear or Linearized Stress-Life (S-N) and Strain-Life (e-N) Fatigue Data (1991).Search in Google Scholar
Received: 2001-01-22
Published Online: 2022-01-08

© 2001 Carl Hanser Verlag, München

Articles in the same Issue

  1. Frontmatter
  2. Editorial
  3. In memoriam
  4. The Ringberg Workshop 1999 on Thermodynamic Modelling and Applications
  5. Aufsätze/Articles
  6. Using Ab Initio Calculations in the Calphad Environment
  7. Contributions to the Thermodynamic Modelling of Solutions
  8. Thermodynamic Modelling of Oxide and Oxynitride Phases
  9. The Modelling of Carbide, Nitride and Carbo-Nitride Phases
  10. Amorphous Phases in Materials Microstructure
  11. Experimental and Theoretical Study of the Al-Rich Corner in the Ternary Al–Ti–B System and Reassessment of the Al-Rich Side of the Binary Al–B Phase Diagram
  12. Evaluation of Superplastic Formability of the AZ31 Magnesium Alloy
  13. Characteristics of Mechanical Alloying of Zn–Al-Based Alloys
  14. The Effect of Sputter Cleaning and TiN Coating after Sputter Cleaning on Tensile and Fatigue Behavior of a Nodular Cast Iron
  15. Nucleation of Iron Nitrides during Gaseous Nitriding of Iron; Effect of a Preoxidation Treatment
  16. Structure Formation of Activated Nickel Catalyst During Caustic Leaching of a Nickel–Aluminium Alloy
  17. Experimental Study on the Electrical Conductivity and Thermo-Electromotive Force of Liquid Pb–Mg-Based Alloys
  18. Interfacial Reactions between the Aluminium Alloy Matrix and Intermetallic Reinforcement Particles in Novel P/M 5056/Ni3Alp Composites
  19. Microstructure and Devitrification Behavior of Melt-Spun Al-Rich Metallic Glasses and Nanostructured Composites
  20. Mitteilungen/Notifications
  21. Personelles/Personal
  22. Bücher/Books
  23. Tagungen/Conferences
https://doi.org/10.3139/ijmr-2001-0113
Keywords for this article
Endurance limit; Fatigue strength; Arc PVD technique; Sputter cleaning; TiN coating

Articles in the same Issue

  1. Frontmatter
  2. Editorial
  3. In memoriam
  4. The Ringberg Workshop 1999 on Thermodynamic Modelling and Applications
  5. Aufsätze/Articles
  6. Using Ab Initio Calculations in the Calphad Environment
  7. Contributions to the Thermodynamic Modelling of Solutions
  8. Thermodynamic Modelling of Oxide and Oxynitride Phases
  9. The Modelling of Carbide, Nitride and Carbo-Nitride Phases
  10. Amorphous Phases in Materials Microstructure
  11. Experimental and Theoretical Study of the Al-Rich Corner in the Ternary Al–Ti–B System and Reassessment of the Al-Rich Side of the Binary Al–B Phase Diagram
  12. Evaluation of Superplastic Formability of the AZ31 Magnesium Alloy
  13. Characteristics of Mechanical Alloying of Zn–Al-Based Alloys
  14. The Effect of Sputter Cleaning and TiN Coating after Sputter Cleaning on Tensile and Fatigue Behavior of a Nodular Cast Iron
  15. Nucleation of Iron Nitrides during Gaseous Nitriding of Iron; Effect of a Preoxidation Treatment
  16. Structure Formation of Activated Nickel Catalyst During Caustic Leaching of a Nickel–Aluminium Alloy
  17. Experimental Study on the Electrical Conductivity and Thermo-Electromotive Force of Liquid Pb–Mg-Based Alloys
  18. Interfacial Reactions between the Aluminium Alloy Matrix and Intermetallic Reinforcement Particles in Novel P/M 5056/Ni3Alp Composites
  19. Microstructure and Devitrification Behavior of Melt-Spun Al-Rich Metallic Glasses and Nanostructured Composites
  20. Mitteilungen/Notifications
  21. Personelles/Personal
  22. Bücher/Books
  23. Tagungen/Conferences
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Winner of the OpenAthens UX Award 2026
Winner of the OpenAthens UX Award 2026
Have an idea on how to improve our website?
Please write us.
© 2026 De Gruyter Brill
Downloaded on 31.3.2026 from https://www.degruyterbrill.com/document/doi/10.3139/ijmr-2001-0113/html
Scroll to top button