Startseite Pressure and Temperature Dependence of LDPE Viscosity and Free Volume: The Effect of Molecular Structure
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Pressure and Temperature Dependence of LDPE Viscosity and Free Volume: The Effect of Molecular Structure

  • T. Sedlacek , A. Lengalova , M. Zatloukal , R. Cermak und P. Saha
Veröffentlicht/Copyright: 6. April 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Manuskript einreichen Informationen für Autor*innen
International Polymer Processing
Aus der Zeitschrift International Polymer Processing Band 21 Heft 2

Abstract

Temperature and pressure dependencies of shear and elongational viscosities were examined using rotational and capillary rheometers. Two different batches of the same polymer grade have shown that the molecular structure diversion significantly influences the magnitudes of pressure coefficients, which vary more than the temperature coefficients. The pressure effect on viscosity notably depends on the amount of long-chain branching in polymer. Further, the paper shows that pVT data analysis via the Simha-Somcynsky equation of state can be employed to reveal differences in temperature and pressure viscosity dependencies through the free volume fraction.

∗ Mail address: T. Sedlacek, Polymer Centre, Tomas Bata University in Zlín, TGM 275, 76272 Zlín, Czech Republic. E-mail:

References

1Couch, M. A., Binding, D. M.: Polymer41, p. 6323 (2000)10.1016/S0032-3861(99)00865-4Suche in Google Scholar

2Sedlacek, T., Zatloukal, M., Filip, P., Boldizar, A., Saha, P.: Polym. Eng. Sci. 44, p. 1328 (2004)10.1002/pen.20128Suche in Google Scholar

3Penwell, R. C., Porter, R. S., Middleman, S.: J. Polym. Sci. 9, p. 731 (1971)10.1002/pol.1971.160090412Suche in Google Scholar

4Kadijk, S. E., van den Brule, B. N. A. A.: Polym. Eng. Sci. 34, p. 1535 (1994)10.1002/pen.760342004Suche in Google Scholar

5Jacovic, M. S., Pollock, D., Porter, R. S.: J. Appl. Polym. Sci. 23, p. 517 (1979)10.1002/app.1979.070230222Suche in Google Scholar

6Starck, P., Lindberg, J. J.: Angew. Makrom. Chem. 75, p. 1 (1979)10.1002/apmc.1979.050750101Suche in Google Scholar

7Kim, Y. S., Chung, C. I., Lai, S. Y., Hyun, K. S.: J. Appl. Polym. Sci. 59, p. 125 (1996)10.1002/(SICI)1097-4628(19960103)59:1<125::AID-APP18>3.0.CO;2-ZSuche in Google Scholar

8Robertson, Ch. G., Garcia-Franco, C. A., Srinivas, S.: J. Polym. Sci.,: Part B: Polym. Phys. 42, p. 1671 (2004)10.1002/polb.20038Suche in Google Scholar

9Cogswell, F. N.: Polymer Melt Rheology. A Guide for Industrial Practice. Woodhead Publishing, Cambridge (1994)10.1533/9780857092984Suche in Google Scholar

10Zatloukal, M., Kopytko, W., Lengalova, A., Vlcek, J.: J. Appl. Polym. Sci. 98, p. 153 (2005)10.1002/app.22030Suche in Google Scholar

11Laun, H. M., Schuch, H.: J. Rheol. 33, p. 119 (1989)10.1122/1.550058Suche in Google Scholar

12Gabriel, C., Münstedt, H.: Rheol. Acta41, p. 232 (2002)10.1007/s00397-001-0219-6Suche in Google Scholar

13Gabriel, C., Münstedt, H.: J. Rheol. 47, p. 619 (2003)10.1122/1.1567752Suche in Google Scholar

14Zatloukal, M., Vlcek, J., Tzoganaki, C., Saha, P.: J. Non-Newt. Fluid Mech. 107, p. 13 (2002)10.1016/S0377-0257(02)00111-8Suche in Google Scholar

15Barnes, H. A., Roberts, G. P.: J. of Non-Newtonian Fluid Mech. 44, p. 113 (1992)10.1016/0377-0257(92)80047-2Suche in Google Scholar

16Simha, R., Somcynsky, T.: Macromolecules2, p. 342 (1969)10.1021/ma60010a005Suche in Google Scholar

17Simha, R.: Macromolecules10, p. 1025 (1977)10.1021/ma60059a028Suche in Google Scholar

18Curro, J. G., Lagasse, R. R., Simha, R.: Macromolecules15, p. 1621 (1982)10.1021/ma00234a032Suche in Google Scholar

19Jain, R. K., Simha, R.: Macromolecules22, p. 464 (1989)10.1021/ma00191a084Suche in Google Scholar

20Carri, B. A., Simha, R.: J. Colloid Interface Sci. 178, p. 483 (1996)10.1006/jcis.1996.0143Suche in Google Scholar

21Rudolf, B., Ougizawa, T., Inoue, T.: Polymer39, p. 873 (1998)10.1016/S0032-3861(97)00356-XSuche in Google Scholar

22Jain, R. K., Simha, R.: J. Colloid Interface Sci. 216, p. 424 (1999)10.1006/jcis.1999.6316Suche in Google Scholar PubMed

23Cogswell, F. N.: Polym. Eng. Sci. 12, p. 64 (1972)10.1002/pen.760120111Suche in Google Scholar

24Cox, W. P., Merz, E. H.: J. Polym. Sci. 28, p. 619 (1958)10.1002/pol.1958.1202811812Suche in Google Scholar

25Simha, R., Wilson, P. S., Olabisi, O.: Kolloid-Z. Z. Polym. 251, p. 402 (1973)10.1007/BF01498686Suche in Google Scholar

26Utracki, L. A., Simha, R.: Macromol. Theory Simul. 10, p. 17 (2001)10.1002/1521-3919(20010101)10:1<17::AID-MATS17>3.0.CO;2-BSuche in Google Scholar

27Utracki, L. A.: Polym. Eng. Sci. 23, p. 446 (1983)10.1002/pen.760230806Suche in Google Scholar

Received: 2005-1-13
Accepted: 2005-11-9
Published Online: 2013-04-06
Published in Print: 2006-05-01

© 2006, Hanser Publishers, Munich

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Regular Contributed Articles
  4. Pressure and Temperature Dependence of LDPE Viscosity and Free Volume: The Effect of Molecular Structure
  5. Correlations between Injection Molding Parameters, Morphology and Mechanical Properties of PPS Using Artificial Neural Networks
  6. Investigations into Kinematic Reversal in Non-isothermal Flows in Single-screw Machines
  7. The Effect of Post-extrusion Conditions in Ribbon Extrusion of Polymer Blends
  8. Effect of the Chemical and Morphological Conditions of the Die Wall on the Extrusion of Linear Polyolefins
  9. Investigation of the Heat Affected Zone of Hot-gas Welded PP Joints
  10. Method for the Optimisation of Screw Elements for Tightly Intermeshing, Co-rotating Twin Screw Extruders
  11. Rheology and Processing of Molten Poly(methyl methacrylate) Resins
  12. PLLA Morphology Controlled by Dry-cast Process
  13. Two Component Injection Molding of Phase Separating Blends
  14. A Low Force Valve for Dynamic Control of Molten Plastics in a Mold
  15. Influence of Drawing and Temperature on the Optical and Structural Properties of Monofilament PP Sutures
  16. Mechanical Properties of Rubber-toughened Post-industrial Glass-fiber-reinforced PA66
  17. Thermal Flow Instability in Metal Injection Molding: Experiment and Simulation
  18. Review Paper
  19. State of the Art: Recycling of EPDM Rubber Vulcanizates
  20. PPS News
  21. PPS News
  22. Seikei-Kakou Abstracts
  23. Seikei-Kakou Abstracts
https://doi.org/10.3139/217.1909

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Regular Contributed Articles
  4. Pressure and Temperature Dependence of LDPE Viscosity and Free Volume: The Effect of Molecular Structure
  5. Correlations between Injection Molding Parameters, Morphology and Mechanical Properties of PPS Using Artificial Neural Networks
  6. Investigations into Kinematic Reversal in Non-isothermal Flows in Single-screw Machines
  7. The Effect of Post-extrusion Conditions in Ribbon Extrusion of Polymer Blends
  8. Effect of the Chemical and Morphological Conditions of the Die Wall on the Extrusion of Linear Polyolefins
  9. Investigation of the Heat Affected Zone of Hot-gas Welded PP Joints
  10. Method for the Optimisation of Screw Elements for Tightly Intermeshing, Co-rotating Twin Screw Extruders
  11. Rheology and Processing of Molten Poly(methyl methacrylate) Resins
  12. PLLA Morphology Controlled by Dry-cast Process
  13. Two Component Injection Molding of Phase Separating Blends
  14. A Low Force Valve for Dynamic Control of Molten Plastics in a Mold
  15. Influence of Drawing and Temperature on the Optical and Structural Properties of Monofilament PP Sutures
  16. Mechanical Properties of Rubber-toughened Post-industrial Glass-fiber-reinforced PA66
  17. Thermal Flow Instability in Metal Injection Molding: Experiment and Simulation
  18. Review Paper
  19. State of the Art: Recycling of EPDM Rubber Vulcanizates
  20. PPS News
  21. PPS News
  22. Seikei-Kakou Abstracts
  23. Seikei-Kakou Abstracts
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 6.9.2025 von https://www.degruyterbrill.com/document/doi/10.3139/217.1909/pdf
Button zum nach oben scrollen