Home Investigations into Kinematic Reversal in Non-isothermal Flows in Single-screw Machines
Article
Licensed
Unlicensed Requires Authentication

Investigations into Kinematic Reversal in Non-isothermal Flows in Single-screw Machines

  • H. Potente , M. Bornemann , D. Heinrich and J. Pape
Published/Copyright: April 6, 2013
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Polymer Processing
From the journal International Polymer Processing Volume 21 Issue 2

Abstract

When describing the flow in single-screw machines in mathematical terms, the screw is generally assumed to be standing still inside a rotating barrel. This study looks into whether and, if so, how far this principle of kinetic reversal falsifies the calculation result. It is performed both on an analytical basis and with the aid of comparative FEA simulations, taking the general case of a non-isothermal flow. It is shown that both kinematic boundary conditions lead to absolutely identical calculation results.

∗ Mail address: M. Bornemann, University of Paderborn, Institut für Kunststofftechnik (KTP), Warburgerstr. 100, D-33098 Paderborn, Germany. E-mail:

References

1Hensen, F., Knappe, W., Potente, H.: Handbuch der Kunststoffextrusionstechnik. Hanser, Munich, Vienna (1989)Search in Google Scholar

2Tadmor, Z., Klein, I.: Engineering Principles of Plasticating Extrusion. Krieger, Huntington, New York (1978)Search in Google Scholar

3Campbell, G. A., Sweeney, P. A., Dontula, N., Wang, C.: Int. Polym. Process. 11, p. 199 (1996)10.3139/217.960199Search in Google Scholar

4Campbell, G. A., Sweeney, P. A., Felton, J. N.: Polym. Eng. Sci. 32, p. 1765 (1992)10.1002/pen.760322305Search in Google Scholar

5Campbell, G. A., Sweeney, P. A., Felton, J. N.: Int. Polym. Process. 7, p. 320 (1992)10.3139/217.920320Search in Google Scholar

6Junsuo, S., Rauwendaal, C.: Paper Presented at the SPE ANTEC, San Francisco (2002)Search in Google Scholar

7Rauwendaal, C., Osswald, T. A., Tellez, G., Gramann, P. J.: Int. Polym. Process. 8, p. 327 (1998)10.3139/217.980327Search in Google Scholar

8Bornemann, M.: Experimental Thesis at the KTP, University of Paderborn (2004)Search in Google Scholar

9Pape, J.: Unpublished Experimental Thesis at the KTP, University of Paderborn (1997)Search in Google Scholar

Received: 2005-4-11
Accepted: 2005-11-8
Published Online: 2013-04-06
Published in Print: 2006-05-01

© 2006, Hanser Publishers, Munich

Articles in the same Issue

  1. Contents
  2. Contents
  3. Regular Contributed Articles
  4. Pressure and Temperature Dependence of LDPE Viscosity and Free Volume: The Effect of Molecular Structure
  5. Correlations between Injection Molding Parameters, Morphology and Mechanical Properties of PPS Using Artificial Neural Networks
  6. Investigations into Kinematic Reversal in Non-isothermal Flows in Single-screw Machines
  7. The Effect of Post-extrusion Conditions in Ribbon Extrusion of Polymer Blends
  8. Effect of the Chemical and Morphological Conditions of the Die Wall on the Extrusion of Linear Polyolefins
  9. Investigation of the Heat Affected Zone of Hot-gas Welded PP Joints
  10. Method for the Optimisation of Screw Elements for Tightly Intermeshing, Co-rotating Twin Screw Extruders
  11. Rheology and Processing of Molten Poly(methyl methacrylate) Resins
  12. PLLA Morphology Controlled by Dry-cast Process
  13. Two Component Injection Molding of Phase Separating Blends
  14. A Low Force Valve for Dynamic Control of Molten Plastics in a Mold
  15. Influence of Drawing and Temperature on the Optical and Structural Properties of Monofilament PP Sutures
  16. Mechanical Properties of Rubber-toughened Post-industrial Glass-fiber-reinforced PA66
  17. Thermal Flow Instability in Metal Injection Molding: Experiment and Simulation
  18. Review Paper
  19. State of the Art: Recycling of EPDM Rubber Vulcanizates
  20. PPS News
  21. PPS News
  22. Seikei-Kakou Abstracts
  23. Seikei-Kakou Abstracts
https://doi.org/10.3139/217.0126

Articles in the same Issue

  1. Contents
  2. Contents
  3. Regular Contributed Articles
  4. Pressure and Temperature Dependence of LDPE Viscosity and Free Volume: The Effect of Molecular Structure
  5. Correlations between Injection Molding Parameters, Morphology and Mechanical Properties of PPS Using Artificial Neural Networks
  6. Investigations into Kinematic Reversal in Non-isothermal Flows in Single-screw Machines
  7. The Effect of Post-extrusion Conditions in Ribbon Extrusion of Polymer Blends
  8. Effect of the Chemical and Morphological Conditions of the Die Wall on the Extrusion of Linear Polyolefins
  9. Investigation of the Heat Affected Zone of Hot-gas Welded PP Joints
  10. Method for the Optimisation of Screw Elements for Tightly Intermeshing, Co-rotating Twin Screw Extruders
  11. Rheology and Processing of Molten Poly(methyl methacrylate) Resins
  12. PLLA Morphology Controlled by Dry-cast Process
  13. Two Component Injection Molding of Phase Separating Blends
  14. A Low Force Valve for Dynamic Control of Molten Plastics in a Mold
  15. Influence of Drawing and Temperature on the Optical and Structural Properties of Monofilament PP Sutures
  16. Mechanical Properties of Rubber-toughened Post-industrial Glass-fiber-reinforced PA66
  17. Thermal Flow Instability in Metal Injection Molding: Experiment and Simulation
  18. Review Paper
  19. State of the Art: Recycling of EPDM Rubber Vulcanizates
  20. PPS News
  21. PPS News
  22. Seikei-Kakou Abstracts
  23. Seikei-Kakou Abstracts
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 7.9.2025 from https://www.degruyterbrill.com/document/doi/10.3139/217.0126/html
Scroll to top button