Startseite Investigation of the influence of Fe on the microstructure and properties of Ti5553 near-β titanium alloy with combinatorial approach
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Investigation of the influence of Fe on the microstructure and properties of Ti5553 near-β titanium alloy with combinatorial approach

  • Di Wu , Ligang Zhang , Libin Liu , Xi Shi , Shuaixiong Huang und Yun Jiang
Veröffentlicht/Copyright: 4. Mai 2017
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 108 Heft 5

Abstract

A combinatorial approach has been applied to build the database of composition dependent microstructure and hardness of the Ti5553–Fe system. The relationship between the composition and microstructure as well as the hardness was obtained. (Ti5553)96-Fe4 was found to have almost the same hardness as that of Ti5553, but a relatively coarser intragranular α phase. High-angle annular dark field imaging revealed that Fe mainly concentrated in the β phase, which strengthened the β phase through solution strengthening. This means that (Ti5553)96-Fe4 may have the same strength as that of Ti5553 but higher fracture toughness. The formation of FeCr compound consumed the β stabilizer elements Fe and Cr, which led to unusual increasing of the nucleation rate and the volume fraction of α phase in (Ti5553)88-Fe12.

Keywords: Near-β titanium alloy; Diffusion multiple; Microstructure; Hardness
*Correspondence address, Libin Liu, Ligang Zhang, School of Material Science and Engineering, Central South University, Lushan Road 932, Changsha, Hunan, 410083, P. R. China, Tel.: +86073188877732, Fax: +86073188876692, E-mail: (Libin Liu, Professor) (Ligang Zhang, Dr.)

References

[1] D.Banerjee, J.C.Williams: Acta Mater.61 (2013) 844. 10.1016/j.actamat.2012.10.043Suche in Google Scholar

[2] R.R.Boyer: Mater. Sci. Eng. A213 (1996) 103. 10.1016/0921-5093(96)10233-1Suche in Google Scholar

[3] J.C.Fanning: J. Mater. Eng. Perform.14 (6) (2005) 788. 10.1361/105994905X75628Suche in Google Scholar

[4] N.G.Jones, R.J.Dashwood, D.Dye, M.Jackson: Mater. Sci. Eng. A490 (2008) 369. 10.1016/j.msea.2008.01.055Suche in Google Scholar

[5] J.Huang, Z.Wang, K.Xue: Mater. Sci. Eng. A528 (2011) 8723. 10.1016/j.msea.2011.08.045Suche in Google Scholar

[6] N.G.Jones, R.J.Dashwood, M.Jackson, D.Dye: Scr. Mater.60 (2009) 571. 10.1016/j.scriptamat.2008.12.010Suche in Google Scholar

[7] S.Nag, R.Banerjee, J.Y.Hwang, M.Harper, H.L.Fraser: Philos. Mag. A89 (2009) 6. 10.1080/14786430802613158Suche in Google Scholar

[8] S.Nag, R.Banerjee, R.Srinivasan, J.Y.Hwang, M.Harper, H.L.Fraser: Acta Mater.57 (2009) 2136. 10.1016/j.actamat.2009.01.007Suche in Google Scholar

[9] S.L.Raghunathan, A.M.Stapleton, R.J.Dashwood, M.Jackson, D.Dye: Acta Mater. 55 (2007) 6861. 10.1016/j.actamat.2007.08.049Suche in Google Scholar

[10] Y.Ohmori, T.Ogo, K.Nakai, S.Kobayashi: Mater. Sci. Eng.A312 (2001) 182. 10.1016/S0921-5093(00)01891-8Suche in Google Scholar

[11] W.F.Ho, C.H.Pan, S.C.Wu, H.C.Hsu: J. Alloys Compd.472 (2009) 546. 10.1016/j.jallcom.2008.05.015Suche in Google Scholar

[12] S.X.Huang, X.D.Zhang, Y.Jiang, Y.R.Jiang, C.Mao, D.Wu, L.G.Zhang, L.B.Liu: Mater. Des.115 (2017) 170. 10.1016/j.matdes.2016.11.056Suche in Google Scholar

[13] Y.R.Jiang, X.Li, Y.Jiang, S.X.Huang, X.Shi, C.Mao, L.G.Zhang, L.B.Liu, F.Zheng: CALPHAD56 (2017) 1. 10.1016/j.calphad.2016.11.004Suche in Google Scholar

[14] C.M.Lee, W.F.Ho, C.P.Ju: J. Mater. Sci.-Mater. Med.13 (2002) 695. PMid:15348579; 10.1023/A:1015798011434Suche in Google Scholar

[15] J.Das, K.B.Kim, W.Xu, W.Loser, J.Eckert: Mater. Sci. Eng.A449 (2007) 737. 10.1016/j.msea.2006.02.374Suche in Google Scholar

[16] R.Banerjee, S.Nag, J.Stechschulte, H.L.Fraser: Biomaterials25 (2004) 3413. PMid:15020114; 10.1016/j.biomaterials.2003.10.041Suche in Google Scholar

[17] J.C.Zhao: Prog. Mater. Sci.51 (2006) 557. 10.1016/j.pmatsci.2005.10.001Suche in Google Scholar

[18] J.C.Zhao: Adv. Eng. Mater.3 (2001) 143. 10.1007/BF02700985Suche in Google Scholar

[19] J.C.Zhao, X.Zheng, D.G.Cahill: Mater. Today12 (2005) 28. 10.1016/S1369-7021(05)71122-6Suche in Google Scholar

[20] J.C.Zhao: Annu. Rev. Mater. Res.35 (2005) 51. 10.1146/annurev.matsci.35.100303.111314Suche in Google Scholar

[21] X.D.Zhang, L.B.Liu, J.C.Zhao, J.L.Wang, F.Zheng, Z.P.Jin: Mater. Sci. Eng. C39 (2014) 273. PMid:24863225; 10.1016/j.msec.2014.02.039Suche in Google Scholar

[22] W.C.Oliver, G.M.Pharr: J. Mater. Res.7 (1992) 1564. 10.1557/JMR.1992.1564Suche in Google Scholar

[23] N.Chollacoop, M.Dao, S.Suresh: Acta Mater.51 (2003) 3713. 10.1016/S1359-6454(03)00186-1Suche in Google Scholar

[24] S.Nag, Y.Zheng, R.E.A.Williams, A.Devaraj, A.Boyne, Y.Wang, P.C.Collins, G.B.Viswanathan, J.S.Tiley, B.C.Muddle, R.Banerjee, H.L.Fraser: Acta Mater.60 (2012) 6247. 10.1016/j.actamat.2012.07.033Suche in Google Scholar

[25] S.K.Kar, A.Ghosh, N.Fulzele, A.Bhattacharjee: Mater. Charact.81 (2013) 37. 10.1016/j.matchar.2013.03.016Suche in Google Scholar

[26] Y.F.Zheng: PhD thesis, Nucleation Mechanisms of Refined Alpha Microstructure in Beta Titanium Alloys, The Ohio State University, USA (2013).Suche in Google Scholar

[27] V.A.Bykov, T.V.Kulikova, L.B.Vedmid, A.Y.Fishman, K.Y.Shunyaev, N.Y.Tarenkova: Phys. Met. Metall.115 (2014) 705. 10.1134/S0031918X14050020Suche in Google Scholar

[28] H.C.Hsua, C.H.Pan, S.C.Wu, W.F.Ho: J. Alloys Compd.474 (2009) 578. 10.1016/j.jallcom.2008.07.003Suche in Google Scholar

[29] D.Y.Qin, Y.F.Lu, Q.Liu, L.Zhou: Mater. Sci. Eng. A561 (2013) 460. 10.1016/j.msea.2013.02.029Suche in Google Scholar

[30] N.Wain, X.J.Hao, G.A.Ravi, X.Wu: Mater. Sci. Eng. A527 (2010) 7673. 10.1016/j.msea.2010.08.032Suche in Google Scholar

[31] A.Ghosh, S.Sivaprasad, A.Bhattacharjee, S.K.Kar: Mater. Sci. Eng. A568 (2013) 61. 10.1016/j.msea.2013.01.017Suche in Google Scholar

[32] D.Y.Qin, Y.FLu, D.ZGuo, L.Zheng, Q.Liu, L.Zhou: Mater. Sci. Eng. A587 (2013) 100. 10.1016/j.msea.2013.08.055Suche in Google Scholar

[33] S.Nag: PhD thesis, Influence of Beta Instabilities on the Early Stages of Nucleation and Growth of Alpha in Beta Titanium Alloys, The Ohio State University, USA (2008).Suche in Google Scholar

[34] T.Furuhara, T.Maki, T.Makino: J. Mater. Process. Technol.117 (2001) 318. 10.1016/S0924-0136(01)00790-Suche in Google Scholar

[35] M.Ahmed, T.Li, G.Casillas, J.M.Cairney, D.Wexler, E.V.Pereloma: J. Alloys Compd.629 (2015) 260. 10.1016/j.jallcom.2015.01.005Suche in Google Scholar

Received: 2016-09-01
Accepted: 2017-01-17
Published Online: 2017-05-04
Published in Print: 2017-05-15

© 2017, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Downloads and the impact of Open Access at IJMR
  5. Original Contributions
  6. A material selection approach using the TODIM (TOmada de Decisao Interativa Multicriterio) method and its analysis
  7. Investigation of the influence of Fe on the microstructure and properties of Ti5553 near-β titanium alloy with combinatorial approach
  8. Evolution of the temperature, microstructures and microsegregation in equiaxed solidification of Al-5 wt.% Cu alloy
  9. Phase composition and microstructure of materials in the Ir–Ru–B system prepared by arc melting and VHP sintering
  10. Thermal shock behavior of rare earth modified alumina ceramic composites
  11. Investigation of tribological and corrosion properties of CuTi–alumina nanocomposite fabricated by mechanical alloying
  12. Effect of acetic acid on corrosion behavior of AISI 201, 304 and 430 stainless steels
  13. Verification of strength mis-match of electron beam welded heavy thickness titanium alloy
  14. Short Communications
  15. Effect of toughening Fe2B by the addition of tungsten on the wear resistance of Fe–B–C alloy
  16. Microstructural stability of heat-resistant high-pressure die-cast Mg-4Al-4Ce alloy
  17. DGM News
  18. DGM News
https://doi.org/10.3139/146.111487
Schlagwörter für diesen Artikel
Near-β titanium alloy; Diffusion multiple; Microstructure; Hardness

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Downloads and the impact of Open Access at IJMR
  5. Original Contributions
  6. A material selection approach using the TODIM (TOmada de Decisao Interativa Multicriterio) method and its analysis
  7. Investigation of the influence of Fe on the microstructure and properties of Ti5553 near-β titanium alloy with combinatorial approach
  8. Evolution of the temperature, microstructures and microsegregation in equiaxed solidification of Al-5 wt.% Cu alloy
  9. Phase composition and microstructure of materials in the Ir–Ru–B system prepared by arc melting and VHP sintering
  10. Thermal shock behavior of rare earth modified alumina ceramic composites
  11. Investigation of tribological and corrosion properties of CuTi–alumina nanocomposite fabricated by mechanical alloying
  12. Effect of acetic acid on corrosion behavior of AISI 201, 304 and 430 stainless steels
  13. Verification of strength mis-match of electron beam welded heavy thickness titanium alloy
  14. Short Communications
  15. Effect of toughening Fe2B by the addition of tungsten on the wear resistance of Fe–B–C alloy
  16. Microstructural stability of heat-resistant high-pressure die-cast Mg-4Al-4Ce alloy
  17. DGM News
  18. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 16.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.111487/html?lang=de
Button zum nach oben scrollen