Startseite Investigation of Al2O3/TiC ceramic cutting tool materials with the addition of SiC-coated h-BN: preparation, mechanical properties, microstructure and wear resistance
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Investigation of Al2O3/TiC ceramic cutting tool materials with the addition of SiC-coated h-BN: preparation, mechanical properties, microstructure and wear resistance

  • Hui Chen , Chonghai Xu , Guangchun Xiao , Zhaoqiang Chen , Guangyong Wu und Mingdong Yi
Veröffentlicht/Copyright: 3. August 2016
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 107 Heft 8

Abstract

SiC-coated h-BN powders ((h-BN)/SiC) were used to substitute h-BN as solid lubricant to prepare Al2O3/TiC/(h-BN)/SiC self-lubricating ceramic cutting tool materials using hot pressing. Microstructure and mechanical properties of the material were studied. Overall improvements in Vickers hardness and fracture toughness were obtained compared with that of Al2O3/TiC/h-BN. The coating of SiC blocks direct contact between h-BN and Al2O3/TiC and hence enables h-BN particles to bond more closely with Al2O3/TiC. The density of the material was dramatically improved because of the decrement of voids around h-BN particles. Dry turning tests were carried out to investigate the wear resistance of the materials when cutting 40Cr quenched and tempered steel. Enhancement in wear resistance, which may result from the improvement in mechanical properties, was observed.

Keywords: Self-lubricating material; Ceramic cutting tool; Mechanical properties; Microstructure; Wear resistance
*Correspondence address, Professor Chonghai Xu, School of Mechanical and Automotive Engineering, Qilu University of Technology, Daxue Road, Western University Science Park, Jinan, 250353, China, Tel.: +86-0531-89631131, Fax: +86-0531-89631131, E-mail:

References

[1] A.S.Kumar, A.R.Durai, T.Sornakumar: Tribol. Int.39 (2006) 191. 10.1016/j.triboint.2005.01.021Suche in Google Scholar

[2] Q.Like, L.Xikun, P.Yang, M.Weimin, Q.Guanming, S.Yanbin: J. Rare Earths25 (2007) 322. 10.1016/s1002-0721(07)60495-5Suche in Google Scholar

[3] Z.Yin, C.Huang, J.Yuan, B.Zou, H.Liu: Ceram. Int.41 (2015) 7059. 10.1016/j.ceramint.2015.02.012Suche in Google Scholar

[4] P.S.Sreejith, B.K.A.Ngoi: J. Mater. Process. Technol.101 (2000) 287. 10.1016/S0924-0136(00)00445-3Suche in Google Scholar

[5] K.Weinert, I.Inasaki, J.W.Sutherland, T.Wakabayashi: CIRP Ann. - Manuf. Technol.53 (2004) 511. 10.1016/s0007-8506(07)60027-4Suche in Google Scholar

[6] S.Debnath, M.M.Reddy, Q.S.Yi: J. Clean. Prod.83 (2014) 33. 10.1016/j.jclepro.2014.07.071Suche in Google Scholar

[7] B.Davoodi, A.H.Tazehkandi: J. Clean. Prod.68 (2014) 234. 10.1016/j.jclepro.2013.12.056Suche in Google Scholar

[8] D.K.Sarma, U.S.Dixit: J. Mater. Process. Technol.190 (1–3) (2007) 160. 10.1016/j.jmatprotec.2007.02.049Suche in Google Scholar

[9] J.A.Ghani, M.Rizal, C.H.Che Haron: J. Clean. Prod.85 (2014) 289. 10.1016/j.jclepro.2014.02.029Suche in Google Scholar

[10] B.Prakash, J.Mukerji, S.Kalia: Am. Ceram. Soc. Bull.77 (1998) 68.Suche in Google Scholar

[11] D.Jianxin, D.Zeliang, Z.Jun, L.Jianfeng, C.Tongkun: Ceram. Int.32 (2006) 499. 10.1016/j.ceramint.2005.03.031Suche in Google Scholar

[12] J.Deng, T.Cao, X.Yang, J.Liu, J.Sun, J.Zhao: Ceram. Int.33 (2007) 213. 10.1016/j.ceramint.2005.09.008Suche in Google Scholar

[13] Y.Wang, Z.Liu: Wear265 (2008) 1720. 10.1016/j.wear.2008.04.009Suche in Google Scholar

[14] D.Jianxin, C.Tongkun, Y.Xuefeng, L.Jianhua: Int. J. Mach. Tools Manuf.46 (2006) 957. 10.1016/j.ijmachtools.2005.07.047Suche in Google Scholar

[15] J.Deng, T.Can, J.Sun: Ceram. Int.31 (2005) 249. 10.1016/j.ceramint.2004.05.009Suche in Google Scholar

[16] Z.Qiao, J.Cheng, L.Kong, J.Yang, Q.Bi, J.Yang: Int. J. Refract. Met. Hard Mater.41 (2013) 322. 10.1016/j.ijrmhm.2013.05.004Suche in Google Scholar

[17] M.Erkin Cura, S.H.Kim, T.Muukkonen, S.Varjus, A.Vaajoki, O.Söderberg, T.Suhonen, U.Kanerva, S.Wohn Lee, S.P.Hannula: Ceram. Int.39 (2013) 2093. 10.1016/j.ceramint.2012.08.065Suche in Google Scholar

[18] C.Xu, G.Xiao, Y.Zhang, B.Fang: Ceram. Int.40 (2014) 10971. 10.1016/j.ceramint.2014.03.101Suche in Google Scholar

[19] C.H.Xu, G.Y.Wu, G.C.Xiao, B.Fang: Int. J. Refract. Met. Hard Mater.45 (2014) 125. 10.1016/j.ijrmhm.2014.04.006Suche in Google Scholar

[20] Y.Xing, J.Deng, J.Zhao, G.Zhang, K.Zhang: Int. J. Refract. Met. Hard Mater.43 (2014) 46. 10.1016/j.ijrmhm.2013.10.019Suche in Google Scholar

[21] J.Li, Y.-S.Yin, R.-X.Shi, L.-P.Ma, J.Li: Surf. Coat. Technol.200 (2006) 3705. 10.1016/j.surfcoat.2005.02.165Suche in Google Scholar

[22] H.Chen, C.Xu, G.Xiao, Z.Chen, J.Ma, G.Wu: Ceram. Int.42 (2016) 5504. 10.1016/j.ceramint.2015.12.102Suche in Google Scholar

[23] N.Liu, M.Shi, Y.Xu, X.You, P.Ren, J.Feng: Int. J. Refract. Met. Hard Mater.22 (2004) 265. 10.1016/j.ijrmhm.2004.09.001Suche in Google Scholar

[24] C.Xu, X.Ai, C.Huang: Wear249 (5) (2001) 503. 10.1016/S0043-1648(01)00581-6Suche in Google Scholar

[25] D.Jianxin, C.Tongkun, L.Lili: J. Eur. Ceram. Soc.25 (2005) 1073. 10.1016/j.jeurceramsoc.2004.03.033Suche in Google Scholar

[26] J.Deng, L.Liu, X.Yang, J.Liu, J.Sun, J.Zhao: Mater. Des.28 (2007) 757. 10.1016/j.matdes.2005.12.003Suche in Google Scholar

[27] A.Evans, T.R.Wilshaw: Acta Metall.24 (1976) 939. 10.1016/0001-6160(76)90042-0Suche in Google Scholar

[28] C.H.Xu, D.M.Sun: Key Eng. Mater.280 (2005) 1783. 10.4028/www.scientific.net/kem.280-283.1783Suche in Google Scholar

[29] D.Jianxin: Ceram. Int.27 (2001) 135. 10.1016/S0272-8842(00)00052-3Suche in Google Scholar

Received: 2016-02-17
Accepted: 2016-04-26
Published Online: 2016-08-03
Published in Print: 2016-08-11

© 2016, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Nanoindentation of carbon microspheres
  5. Thermal and mechanical properties of single-walled and multi-walled carbon nanotube polycarbonate polyurethane composites with a focus on self-healing
  6. Preparation and characterization of ZnO nanorod arrays produced using wet methods
  7. Phase equilibria of the Al–Zn–Fe–V quaternary system at 620 °C
  8. Effect of withdrawal rate and zinc content on pore structure and morphology of lotus-type porous Cu–Zn alloys fabricated using continuous casting
  9. Investigation of tungsten surface changes after interaction with dense plasma streams compared with the results given by a simple 1D model
  10. Investigation of Al2O3/TiC ceramic cutting tool materials with the addition of SiC-coated h-BN: preparation, mechanical properties, microstructure and wear resistance
  11. Effect of the addition of different sintering aids on the densification behavior of zirconia-toughened alumina nanocomposite powder
  12. Mixed mode notch-crack fatigue propagation in the welding zone of 06Cr19Ni10 austenitic stainless steel: Effect of strain strengthening
  13. A study on mechanical and microstructural properties of dissimilar FSWed joints of AA5251–AA5083 plates
  14. Short Communications
  15. A methodology for in-situ micro-compression testing of fiber composites
  16. The synthesis and electrochemical performance of Cu6Sn5 intermetallic nanoparticles as anode material in Li ion batteries
  17. DGM News
  18. DGM News
https://doi.org/10.3139/146.111395
Schlagwörter für diesen Artikel
Self-lubricating material; Ceramic cutting tool; Mechanical properties; Microstructure; Wear resistance

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Nanoindentation of carbon microspheres
  5. Thermal and mechanical properties of single-walled and multi-walled carbon nanotube polycarbonate polyurethane composites with a focus on self-healing
  6. Preparation and characterization of ZnO nanorod arrays produced using wet methods
  7. Phase equilibria of the Al–Zn–Fe–V quaternary system at 620 °C
  8. Effect of withdrawal rate and zinc content on pore structure and morphology of lotus-type porous Cu–Zn alloys fabricated using continuous casting
  9. Investigation of tungsten surface changes after interaction with dense plasma streams compared with the results given by a simple 1D model
  10. Investigation of Al2O3/TiC ceramic cutting tool materials with the addition of SiC-coated h-BN: preparation, mechanical properties, microstructure and wear resistance
  11. Effect of the addition of different sintering aids on the densification behavior of zirconia-toughened alumina nanocomposite powder
  12. Mixed mode notch-crack fatigue propagation in the welding zone of 06Cr19Ni10 austenitic stainless steel: Effect of strain strengthening
  13. A study on mechanical and microstructural properties of dissimilar FSWed joints of AA5251–AA5083 plates
  14. Short Communications
  15. A methodology for in-situ micro-compression testing of fiber composites
  16. The synthesis and electrochemical performance of Cu6Sn5 intermetallic nanoparticles as anode material in Li ion batteries
  17. DGM News
  18. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 2.10.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.111395/html
Button zum nach oben scrollen