A study on mechanical and microstructural properties of dissimilar FSWed joints of AA5251–AA5083 plates
-
Rohollah Akbari
Abstract
This paper investigates the influence of rotational and travel speed on the structure and mechanical properties of different regions of friction stir welded dissimilar AA5251–AA5083 joints. It was observed that increasing rotational speed from 800 to 1 250 rpm, at a fixed travel speed, increased the grain size from 6.31 μm to 10.64 μm. This stemmed from higher heat input which is generated at higher rotational speed. Furthermore, it was discovered that at 1 000 rpm, 115 mm min−1 and also 1 250 rpm, 85 mm min−1, defect-free welds were produced. The results of tensile testing revealed that the best consistent tensile strength was produced at 1 000 rpm rotational speed and 115 mm min−1 travel speed with an average value of about 200 MPa. Further, the results clearly showed that the hardness values gradually increase from the 5251 aluminum side to the 5083 aluminum side.
References
[1] A.Mehrani Milani, M.Paidar, A.Khodabandeh, S.Nategh: Int. J. Adv. Manuf. Technol.82 (2016) 1495. 10.1007/s00170-015-7505-4Suche in Google Scholar
[2] M.Paidar, A.Khodabandeh, H.Najafi, A.Sabour Rouh-aghdam: J. Mech. Sci. Technol.28(2014) 4893. 10.1007/s12206-014-1108-0Suche in Google Scholar
[3] M.Paidar, A.Khodabandeh, H.Najafi, A.Sabour Rouh-aghdam: Int. J. Adv. Manuf. Technol.80 (2015) 183. 10.1007/s00170-015-6997-2Suche in Google Scholar
[4] K.V.Jata, K.K.Sankaran, J.Ruschau: Metall. Mater. Trans. A31 (2000) 2181. 10.1007/s11661-000-0136-9Suche in Google Scholar
[5] C.G.Rhodes, M.W.Mahoney, W.H.Bingel, R.A.Spurling, C.C.Bampton: Scr. Mater.36 (1997) 69–75. 10.1016/S1359-6462(96)00344-2Suche in Google Scholar
[6] M.W.Mahoney, C.G.Rhodes, J.G.Flintoff, W.H.Bingel, R.A.Spurling: Metall. Mater. Trans. A29 (1998) 1955–1964. 10.1007/s11661-998-0021-5Suche in Google Scholar
[7] D.M.Rodrigues, A.Loureiro, C.Leitao, R.M.Leal, B.M.Chaparro, P.Vilaça: Mater. Des.30 (2009) 1913. 10.1016/j.matdes.2008.09.016Suche in Google Scholar
[8] E.Salari, M.Jahazi, A.Khodabandeh, H.Ghasemi-Nanesa: Mater. Des.58 (2014) 381. 10.1016/j.matdes.2014.02.005Suche in Google Scholar
[9] T.Sakthivel, G.S.Sengar, J.Mukhopadhyay: Int. J. Adv. Manuf. Technol.43 (2009) 468. 10.1007/s00170-008-1727-7Suche in Google Scholar
[10] M.Ghosh, K.Kumar, S.V.Kailas, A.K.Ray: Mater. Des.31 (2010) 3033. 10.1016/j.matdes.2010.01.028Suche in Google Scholar
[11] P.Cavaliere, R.Nobile, F.W.Panella, A.Squillace: Int. J. Mach. Tools Manuf.46 (2006) 588. 10.1016/j.ijmachtools.2005.07.010Suche in Google Scholar
[12] L.Dubourg, A.Merati, M.Jahazi: Mater. Des.31 (2010) 3324. 10.1016/j.matdes.2010.02.002Suche in Google Scholar
[13] R.Palanivel, P.Koshy Mathews, N.Murugan, I.Dinaharan: Mater. Des.40 (2012) 7. 10.1016/j.matdes.2012.03.027Suche in Google Scholar
[14] S.O.Yoon, M.S.Kang, H.B.Nam, Y.J.Kwon, S.T.Hong, J.C.Kim, K.H.Lee, C.Y.Lim, J.D.Seo: Trans. Nonferrous Met. Soc. China22 (2012) 619. 10.1016/S1003-6326(12)61774-9Suche in Google Scholar
[15] A.Masoudian, A.Tahaei, A.Shakiba, F.Sharifianjazi, J.Aghazadeh Mohandesi: Trans. Nonferrous Met. Soc. China24 (2014) 1317. 10.1016/S1003-6326(14)63194-0Suche in Google Scholar
[16] H.Aydin, M.Tutar, A.Durmus, A.Bayram, T.Sayaca: Trans. Indian Inst. Met.65 (2012) 21. 10.1007/s12666-011-069-6Suche in Google Scholar
[17] H.Bisadi, A.Tavakoli, M.Tour Sangsaraki, K.Tour Sangsaraki: Mater. Des.43 (2013) 80. 10.1016/j.matdes.2012.06.029Suche in Google Scholar
[18] J.A.Al-Jarrah, S.Swalha, T.Abu Mansour, M.Ibrahim, M.Al-Rashdan, D.A.Al-Qahsi: Mater. Des.56 (2014) 929. 10.1016/j.matdes.2013.12.003Suche in Google Scholar
[19] M.Simoncini, A.Forcellese: Mater. Des.41 (2012) 50. 10.1016/j.matdes.2012.04.057Suche in Google Scholar
[20] M.Paidar, F.Sadeghi, H.R.Najafi, A.R.Khodabandeh: J. Eng. Mater. Technol.137 (2015). 10.1115/1.4030197Suche in Google Scholar
[21] W.Xu, J.Liu, H.Zhu, L.Fu: Mater. Des.47 (2013) 599. 10.1016/j.matdes.2012.12.065Suche in Google Scholar
[22] Y.Zhao, S.Lin, L.Wu, F.Qu: Mater. Lett.59 (2005) 2948. 10.1016/j.matlet.2005.04.048Suche in Google Scholar
[23] A.Scialpi, M.De Giorgi, L.A.C.De Filippis, R.Nobile, F.W.Panella: Mater. Des.29 (2008) 928. 10.1016/j.matdes.2007.04.006Suche in Google Scholar
[24] H.Eftekharinia, A.A.Amadeh, A.Khodabandeh, M.Paidar: Rare Met. (2016). 10.1007/s12598-016-0691-xSuche in Google Scholar
[25] H.J.Zhang, H.J.Liu, L.Yu: Mater. Des.32 (2011) 4402. 10.1016/j.matdes.2011.03.073Suche in Google Scholar
[26] Y.F.Sun, H.Fujii: Mater. Sci. Eng. A528 (2011) 5470. 10.1016/j.msea.2011.03.077Suche in Google Scholar
[27] P.M.G.P.Moreira, T.Santos, S.M.O.Tavares, V.Richter-Trummer, P.Vilaça, P.M.S.T.De Castro: Mater. Des.30 (2009) 180. 10.1016/j.matdes.2008.04.042Suche in Google Scholar
[28] H.Liu, H.Zhang, Q.Pan, L.Yu: Int. J. Mater. Form.5 (2012) 235. 10.1007/s12289-011-1048-5Suche in Google Scholar
[29] M.Mohammadi pour, A.Khodabandeh, S.Mohammadi pour, M.Paidar: Rare Met. (2016). 10.1007/s12598-016-0692-9Suche in Google Scholar
[30] W.Y.Li, T.Fu, L.Hütsch, J.Hilgert, F.F.Wang, J.F.Dos Santos, N.Huber: Mater. Des.64 (2014) 714. 10.1016/j.matdes.2014.07.023Suche in Google Scholar
[31] H.Jamshidi Aval: Mater. Des.67 (2014) 413. 10.1016/j.matdes.2014.11.055Suche in Google Scholar
[32] M.Abbasi Gharacheh, A.H.Kokabi, G.H.Daneshi, B.Shalchi, R.Sarrafi: Int. J. Mach. Tools Manuf.46 (2006) 1983. 10.1016/j.ijmachtools.2006.01.007Suche in Google Scholar
[33] P.Motalleb-nejad, T.Saeid, A.Heidarzadeh, K.Darzi, M.Ashjari: Mater. Des.59 (2014) 221. 10.1016/j.matdes.2014.02.068Suche in Google Scholar
[34] Z.Song, K.Nakata, A.Wu, J.Liao, L.Zhou: Mater. Des.57 (2014) 269. 10.1016/j.matdes.2013.12.040Suche in Google Scholar
[35] B.Han, Y.Huang, S.Lv, L.Wan, J.Feng, G.Fu: Mater. Des.51 (2013) 25. 10.1016/j.matdes.2013.03.089Suche in Google Scholar
[36] G.İpekoğlu, B.G.Kiral, S.Erim, G.Çam: Mater. Technol.46 (2012) 627–632. ISSN 1580-2949, MTAEC9, 46(6)627 (2012).Suche in Google Scholar
© 2016, Carl Hanser Verlag, München
Artikel in diesem Heft
- Contents
- Contents
- Original Contributions
- Nanoindentation of carbon microspheres
- Thermal and mechanical properties of single-walled and multi-walled carbon nanotube polycarbonate polyurethane composites with a focus on self-healing
- Preparation and characterization of ZnO nanorod arrays produced using wet methods
- Phase equilibria of the Al–Zn–Fe–V quaternary system at 620 °C
- Effect of withdrawal rate and zinc content on pore structure and morphology of lotus-type porous Cu–Zn alloys fabricated using continuous casting
- Investigation of tungsten surface changes after interaction with dense plasma streams compared with the results given by a simple 1D model
- Investigation of Al2O3/TiC ceramic cutting tool materials with the addition of SiC-coated h-BN: preparation, mechanical properties, microstructure and wear resistance
- Effect of the addition of different sintering aids on the densification behavior of zirconia-toughened alumina nanocomposite powder
- Mixed mode notch-crack fatigue propagation in the welding zone of 06Cr19Ni10 austenitic stainless steel: Effect of strain strengthening
- A study on mechanical and microstructural properties of dissimilar FSWed joints of AA5251–AA5083 plates
- Short Communications
- A methodology for in-situ micro-compression testing of fiber composites
- The synthesis and electrochemical performance of Cu6Sn5 intermetallic nanoparticles as anode material in Li ion batteries
- DGM News
- DGM News
Artikel in diesem Heft
- Contents
- Contents
- Original Contributions
- Nanoindentation of carbon microspheres
- Thermal and mechanical properties of single-walled and multi-walled carbon nanotube polycarbonate polyurethane composites with a focus on self-healing
- Preparation and characterization of ZnO nanorod arrays produced using wet methods
- Phase equilibria of the Al–Zn–Fe–V quaternary system at 620 °C
- Effect of withdrawal rate and zinc content on pore structure and morphology of lotus-type porous Cu–Zn alloys fabricated using continuous casting
- Investigation of tungsten surface changes after interaction with dense plasma streams compared with the results given by a simple 1D model
- Investigation of Al2O3/TiC ceramic cutting tool materials with the addition of SiC-coated h-BN: preparation, mechanical properties, microstructure and wear resistance
- Effect of the addition of different sintering aids on the densification behavior of zirconia-toughened alumina nanocomposite powder
- Mixed mode notch-crack fatigue propagation in the welding zone of 06Cr19Ni10 austenitic stainless steel: Effect of strain strengthening
- A study on mechanical and microstructural properties of dissimilar FSWed joints of AA5251–AA5083 plates
- Short Communications
- A methodology for in-situ micro-compression testing of fiber composites
- The synthesis and electrochemical performance of Cu6Sn5 intermetallic nanoparticles as anode material in Li ion batteries
- DGM News
- DGM News
