Article
Licensed
Unlicensed Requires Authentication

The influence of ECAP on microstructure evolution of aluminium alloys during in-situ heating in TEM

Paper presented at “XV International Conference on Electron Microscopy”, 15–18 September 2014, Cracow, Poland
  • , and
Published/Copyright: July 9, 2015
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 106 Issue 7

Abstract

Twin-roll casting of aluminium alloys produces sheets with high solid-solution supersaturation. During high tempe-rature processing the solid solution decomposes and cubic α-Al(Mn, Fe)Si precipitates form. Processing by equal channel angular pressing introduces new grain boundaries into the material and shifts the precipitation to lower temperatures. In-situ annealing in a transmission electron microscope enables dynamic observation of recovery, precipitation, particle dissolution and grain growth. However, most of the processes observed by in-situ transmission electron microscopy occur at temperatures that are lower than temperatures estimated from specimens annealed conventionally in a furnace.

Keywords: Transmission electron microscopy; In-situ annealing; Precipitation; Equal channel angular pressing; Electrical resistivity
*Correspondence address, RNDr. Michaela Poková, Ph. D., Ke Karlovu 5, 121 16, Prague 2, Czech Republic, Tel.: +420 221 911 386, Fax: +420 221 911 490, E-mail:

References

[1] M.Slámová, M.Karlík, M.Cieslar, B.Chalupa, P.Merle: Kovove Mater. 40 (2002) 389.Search in Google Scholar

[2] M.Karlík, T.Mánik, H.Lauschman: J. Alloys Compd.515 (2012) 108. 10.1016/j.jallcom.2011.11.101Search in Google Scholar

[3] M.Cieslar, M.Slámová, J.Uhlíř, C.Coupeau, J.Bonneville: Kovove Mater. 45 (2007) 91.Search in Google Scholar

[4] M.Poková, M.Cieslar, J.Lacaze: Acta Phys. Pol. A122 (2012) 625.10.12693/APhysPolA.122.625Search in Google Scholar

[5] M.Slámová, A.Kubošová, J.Politello, M.Cieslar: Int. J. Mater. Res.100 (2009) 428. 10.3139/146.110044Search in Google Scholar

[6] M.Poková, M.Cieslar: Mater. Sci. Eng.: IOP Conference Series63 (2014) 012086. 10.1088/1757-899X/63/1/012086Search in Google Scholar

[7] C.Gras, M.Meredith, J.D.Hunt: J. Mater. Process. Technol.169 (2005) 156. 10.1016/j.jmatprotec.2005.03.034Search in Google Scholar

[8] T.Carlberg, M.Jaradech, H.K.Kamga: JOM-J. Min. Met. Mater. Soc.58 (2006) 56. 10.1007/s11837-006-0025-9Search in Google Scholar

[9] M.Poková, M.Cieslar, M.Slámová: Int. J. Mater. Res.100 (2009) 391. 10.3139/146.110029Search in Google Scholar

[10] M.Cieslar, M.Slámová, M.Hájek, J.Veselý: Mater. Sci. Forum567–568 (2008) 325.Search in Google Scholar

[11] M.Dehmas, P.Archambault, M.Serriere, E.Gautier, C.A.Gandin: Aluminium78 (2002) 864.Search in Google Scholar

[12] N.A.Belov, D.G.Eskin, A.A.Askenov: Multicomponent Phase Diagrams: Application for Commercial Aluminum Alloys, Elsevier (2005).Search in Google Scholar

[13] Y.Birol: J. Alloys Compd.471 (2009) 122. 10.1016/j.jallcom.2008.04.005Search in Google Scholar

[14] T.Pettersen, Y.Li, T.Furu, K.Marthinsen: Mater. Sci. Forum558–559 (2007) 301. 10.4028/www.scientific.net/MSF.558-559.301Search in Google Scholar

[15] I.Nikulin, A.Kipelova, S.Malopheyev, R.Kaibyshev: Acta Mater. 60 (2012) 487. 10.1016/j.actamat.2011.10.023Search in Google Scholar

[16] Y.Iwahashi, Z.Horita, M.Nemoto, T.G.Langdon: Acta Mater. 45 (1997) 4733. 10.1016/S1359-6454(97)00100-6Search in Google Scholar

[17] M.Cabibbo: Mater. Sci. Eng. A-Struct.560 (2013) 413. 10.1016/j.msea.2012.09.086Search in Google Scholar

[18] P.Málek, M.Poková, M.Cieslar: Metal 2014 Conference Proceedings (2014) 2839.Search in Google Scholar

[19] A.B.Naizabekov, V.A.Andreyachshenko, R.Kocich: Micron44 (2013) 210. 10.1016/j.micron.2012.06.011Search in Google Scholar

[20] K.Nakashima, Z.Horita, M.Nemoto, T.G.Langdon: Mater. Sci. Eng. A-Struct.281 (2000) 82. 10.1016/S0921-5093(99)00744-3Search in Google Scholar

[21] M.Hájek, J.Veselý, M.Cieslar: Mater. Sci. Eng. A-Struct.462 (2007) 339. 10.1016/j.msea.2006.01.175Search in Google Scholar

[22] M.Vlach, I.Stulíková, B.Smola, T.Kekule, H.Kudrnová, S.Daniš, R.Gemma, V.Očenášek, J.Málek, D.Tanprayoon, V.Neubert: Mater. Charact.86 (2013) 59. 10.1016/j.matchar.2013.09.010Search in Google Scholar

Received: 2014-12-04
Accepted: 2015-03-09
Published Online: 2015-07-09
Published in Print: 2015-07-04

© 2015, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Phase transitions induced by severe plastic deformation: steady-state and equifinality
  5. Dynamic precipitation of nickel-based superalloys undergoing severe deformation below the solvus temperature
  6. The influence of ECAP on microstructure evolution of aluminium alloys during in-situ heating in TEM
  7. An investigation into the effect of isothermal annealing on the structure (XRD), microstructure (SEM, TEM) and magnetic properties of amorphous ribbons and bulk amorphous plates
  8. Analysis of the structure (XRD) and microstructure (TEM, SEM, AFM) of bulk amorphous and nanocrystalline alloys based on FeCoB
  9. Preparation and characterization of silicon nanowires using SEM/FIB and TEM
  10. In-situ TEM heating of Ni/Al multilayers
  11. Microstructure and martensitic transformation in Ni48Mn39.5Sn12.5–xSix metamagnetic Heusler alloy ribbons
  12. Evolution of Fe-rich compounds in a secondary Al–Si–Cu alloy: influence of cooling rate
  13. Microstructural evolution and grain refinement in an intermetallic titanium aluminide alloy with a high molybdenum content
  14. Microstructure and properties of thick nanocomposite TiN/Si3N4 coatings on Vanadis 23 HS steel
  15. Influence of casting procedure on microstructure and properties of Mg alloy–glassy carbon particle composite
  16. Microstructural characterization of nanostructured supersonic sprayed Ni–Sn coatings after wear tests at elevated temperature
  17. On the wear of TiBx/TiSiyCz coatings deposited on 316L steel
  18. 3D reconstruction and characterization of carbides in Ni-based high carbon alloy in a FIB-SEM system
  19. Microstructural evolution in deformed duplex stainless steels
  20. Microstructure and interfacial reactions in the bonding zone of explosively welded Zr700 and carbon steel plates
  21. Microstructural characterization of second phases in X10CrMoVNb9–1 and 12CrMoWCuVNb steels after long steam exposure time at 550°C
  22. Short Communications
  23. Novel multilayer nano-composite protective coatings for metallic medical tools
  24. Microstructural changes in Cu-5.8 at.% In alloy caused by high pressure torsion
  25. Electron microscopy investigation of a cast AlSi9Mg aluminum alloy subjected to friction stir processing with overlapping passes
  26. DGM News
  27. DGM News
https://doi.org/10.3139/146.111243
Keywords for this article
Transmission electron microscopy; In-situ annealing; Precipitation; Equal channel angular pressing; Electrical resistivity

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Phase transitions induced by severe plastic deformation: steady-state and equifinality
  5. Dynamic precipitation of nickel-based superalloys undergoing severe deformation below the solvus temperature
  6. The influence of ECAP on microstructure evolution of aluminium alloys during in-situ heating in TEM
  7. An investigation into the effect of isothermal annealing on the structure (XRD), microstructure (SEM, TEM) and magnetic properties of amorphous ribbons and bulk amorphous plates
  8. Analysis of the structure (XRD) and microstructure (TEM, SEM, AFM) of bulk amorphous and nanocrystalline alloys based on FeCoB
  9. Preparation and characterization of silicon nanowires using SEM/FIB and TEM
  10. In-situ TEM heating of Ni/Al multilayers
  11. Microstructure and martensitic transformation in Ni48Mn39.5Sn12.5–xSix metamagnetic Heusler alloy ribbons
  12. Evolution of Fe-rich compounds in a secondary Al–Si–Cu alloy: influence of cooling rate
  13. Microstructural evolution and grain refinement in an intermetallic titanium aluminide alloy with a high molybdenum content
  14. Microstructure and properties of thick nanocomposite TiN/Si3N4 coatings on Vanadis 23 HS steel
  15. Influence of casting procedure on microstructure and properties of Mg alloy–glassy carbon particle composite
  16. Microstructural characterization of nanostructured supersonic sprayed Ni–Sn coatings after wear tests at elevated temperature
  17. On the wear of TiBx/TiSiyCz coatings deposited on 316L steel
  18. 3D reconstruction and characterization of carbides in Ni-based high carbon alloy in a FIB-SEM system
  19. Microstructural evolution in deformed duplex stainless steels
  20. Microstructure and interfacial reactions in the bonding zone of explosively welded Zr700 and carbon steel plates
  21. Microstructural characterization of second phases in X10CrMoVNb9–1 and 12CrMoWCuVNb steels after long steam exposure time at 550°C
  22. Short Communications
  23. Novel multilayer nano-composite protective coatings for metallic medical tools
  24. Microstructural changes in Cu-5.8 at.% In alloy caused by high pressure torsion
  25. Electron microscopy investigation of a cast AlSi9Mg aluminum alloy subjected to friction stir processing with overlapping passes
  26. DGM News
  27. DGM News
Downloaded on 13.4.2026 from https://www.degruyterbrill.com/document/doi/10.3139/146.111243/html
Scroll to top button