Home Technology Wear behaviour of Al/(Al2O3 + ZrB2 + TiB2) hybrid composites fabricated by hot pressing
Article
Licensed
Unlicensed Requires Authentication

Wear behaviour of Al/(Al2O3 + ZrB2 + TiB2) hybrid composites fabricated by hot pressing

  • Faranak Farhadinia and Arman Sedghi EMAIL logo
Published/Copyright: October 27, 2021
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 106 Issue 2

Abstract

The dry sliding wear behaviour of Al/(Al2O3 + ZrB2 + TiB2) hybrid composite was tested by using a pin-on-disc testing machine at room temperature and 300 °C. Hybrid reinforcement was fabricated by mechanically activated combustion synthesis, and the composites were prepared by hot pressing of aluminium powder and hybrid reinforcement. The effect of sliding distance, hybrid reinforcement content and temperature on the wear properties of the composites has been investigated. For comparison, the same tests were conducted on Al/Al2O3 composite and pure aluminium. Hybrid composites have higher wear resistance than pure aluminium and Al/Al2O3 composites at room temperature and 300 °C. A study of wear surfaces showed that plastic deformation induced wear and adhesive wear are the dominant mechanisms at room and high temperature, respectively.

Keywords: Hybrid reinforcement; Aluminium matrix composite; ZrB2; TiB2; Wear
Dr. Arman Sedghi Materials Engineering Department Imam Khomeini International University Qazvin, 34149-16818 Iran Tel.: +98 09121776559 Fax: +98 02634572536

References

[1] N. Hosseini, F. Karimzadeh, M.H. Enayati: Mater. Des. 31 (2010) 4777. DOI:10.1016/j.matdes.2010.03.01610.1016/j.matdes.2010.03.016Search in Google Scholar

[2] O. Yilmaz, S. Buytoz: Compos. Sci. Technol. 61 (2001) 2381. DOI:10.1016/S0266-3538(01)00070-710.1016/S0266-3538(01)00070-7Search in Google Scholar

[3] S.C. Tjong, S.Q. Wu, H.G. Zhu: Compos. Sci. Technol. 59 (1999) 1341. DOI:10.1016/S0266-3538(98)00151-110.1016/S0266-3538(98)00151-1Search in Google Scholar

[4] M. Rahimian, N. Parvin, N. Ehsani: Mater. Des. 32 (2011) 1031. DOI:10.1016/j.matdes.2010.07.01610.1016/j.matdes.2010.07.016Search in Google Scholar

[5] J.B. Fogagnold: Mater. Sci. 39 (2004) 127. DOI:10.1023/B:JMSC.0000007736.03608.e510.1023/B:JMSC.0000007736.03608.e5Search in Google Scholar

[6] M. Adamiak: J. Achievements Mater. Manuf. Eng. 14 (2006) 43.Search in Google Scholar

[7] D.D. Radev, D. Klissurski: Mater. Synth. Proc. 9 (2001) 131. DOI:10.1023/A:101324541384010.1023/A:1013245413840Search in Google Scholar

[8] N. Setoudeh, N.J. Welham: J. Alloys Compd. 420 (2006) 225. DOI:10.1016/j.jallcom.2005.07.08310.1016/j.jallcom.2005.07.083Search in Google Scholar

[9] J.S. Peters, B.A. Cook, J.L. Harringa, A.M. Russell: Wear 267 (2009) 136. DOI:10.1016/j.wear.2009.01.03710.1016/j.wear.2009.01.037Search in Google Scholar

[10] P. Millet, T. Hwang: Mater. Sci. 31 (1996) 351. DOI:10.1007/BF0113915110.1007/BF01139151Search in Google Scholar

[11] D. Zhao, X. Liu, Y. Liu, X. Bian: Mater. Sci. 40 (2005) 4365. DOI:10.1007/s10853-005-0705-910.1007/s10853-005-0705-9Search in Google Scholar

[12] G. Abouelmagd: Mater. Proc. Technol. 155–156 (2004) 1395. DOI:10.1016/j.jmatprotec.2004.04.22310.1016/j.jmatprotec.2004.04.223Search in Google Scholar

[13] M. Kok: Composites Part A 37 (2006) 457. 10.1016/j.compositesa.2005.05.038Search in Google Scholar

[14] C.S. Ramesh, Abrar Ahamed: Wear 271 (2011) 1928–1939. DOI:10.1016/j.wear.2010.12.04810.1016/j.wear.2010.12.048Search in Google Scholar

[15] A. Mandal, M. Chakraborty, B.S. Murty: Wear 262 (2007) 160. DOI:10.1016/j.wear.2006.04.00310.1016/j.wear.2006.04.003Search in Google Scholar

[16] A. Mandal, B.S. Murty, M. Chakraborty: Wear 266 (2009) 865. DOI:10.1016/j.wear.2008.12.01110.1016/j.wear.2008.12.011Search in Google Scholar

[17] F. Farhadinia, A. Sedghi: Metall. Mater. Trans. 45A (2014) 3125. DOI:10.1007/s11661-014-2246-910.1007/s11661-014-2246-9Search in Google Scholar

[18] H. Zhu, H. Wang, L. Ge: Wear 264 (2008) 967. DOI:10.1016/j.wear.2007.07.00410.1016/j.wear.2007.07.004Search in Google Scholar

[19] M. Nofar, H.R. Madaah Hosseini, N. Kolagar-Daroonkolaie: Mater. Des. 30 (2009) 280. DOI:10.1016/j.matdes.2008.04.07110.1016/j.matdes.2008.04.071Search in Google Scholar

[20] C. Tijun, L. Jian, H. Yuan: Res. Dev. 6 (2009) 319.Search in Google Scholar

[21] M. All-Qutub, I.M. Allam, M.A. Abdul Samad: Mater. Sci. 43 (2008) 5797. DOI:10.1007/s10853-008-2867-810.1007/s10853-008-2867-8Search in Google Scholar

[22] M. Singla, L. Singh, V. Chawla: J. Miner. Mater. Charact. Eng. 8 (2009) 813.Search in Google Scholar

[23] R. Fuentes-Ramirez, A. Perez-Gonzalez, V.M. Castano Meneses: Met. Sci. Heat Treat. 52 (2010) 368. DOI:10.1007/s11041-010-9284-810.1007/s11041-010-9284-8Search in Google Scholar

[24] T. Shou-fu, J. Long-tao, W. Gao-hui: Trans. Nonferrous Met. Soc. China. 21 (2011) 295. DOI:10.1016/S1003-6326(11)61594-X10.1016/S1003-6326(11)61594-XSearch in Google Scholar

[25] S.K. Mishra, P.K.P. Rupa, S.K. Das, V. Shcherbakov: Sci. Technol. 67 (2007) 1734. 10.1016/j.compscitech.2006.05.014Search in Google Scholar

Received: 2014-08-15
Accepted: 2014-10-15
Published Online: 2021-10-27

© 2015 Carl Hanser Verlag GmbH & Co. KG

Articles in the same Issue

  1. Frontmatter
  2. Original Contributions
  3. Microstructures of magnetron sputtered Fe–Au thin films
  4. Phase-field simulation of diffusion-controlled coarsening kinetics of γ’ phase in Ni–Al alloy
  5. Structural and magnetic evolution of ball milled nanocrystalline Fe-50 at.% Al alloy
  6. Structural, optical and magnetic properties of nanocrystalline zinc ferrite particles from glycine assisted combustion: Effect of Sr2+ dopant
  7. Correlation of plastic deformation induced intermittent electromagnetic radiation characteristics with mechanical properties of Cu–Ni alloys
  8. Effect of isothermal quenching methods on impact toughness and wear resistance in high boron steel
  9. Wear behaviour of Al/(Al2O3 + ZrB2 + TiB2) hybrid composites fabricated by hot pressing
  10. Regression analysis of bonding strength of sprayed coatings based on acoustic emission signal
  11. Effect of substrates on covalent surface modification of graphene using photosensitive functional group
  12. Short Communications
  13. Investigation of optimum nucleation temperature and heating rate of cordierite glass-ceramics
  14. The influence of process parameters on the preparation of CaF2@Al(OH)3 composite powder via heterogeneous nucleation
  15. Effect of zirconium and heat treatment on the microstructure and properties of cast chromium bronze for conductive parts
  16. The influence of addition of citric acid on the physical properties of metallic oxide nanorods via Sol-Gel route preparation
  17. Notifications
  18. People
  19. DGM News
  20. Conferences
https://doi.org/10.3139/146.111165
Keywords for this article
Hybrid reinforcement; Aluminium matrix composite; ZrB2; TiB2; Wear

Articles in the same Issue

  1. Frontmatter
  2. Original Contributions
  3. Microstructures of magnetron sputtered Fe–Au thin films
  4. Phase-field simulation of diffusion-controlled coarsening kinetics of γ’ phase in Ni–Al alloy
  5. Structural and magnetic evolution of ball milled nanocrystalline Fe-50 at.% Al alloy
  6. Structural, optical and magnetic properties of nanocrystalline zinc ferrite particles from glycine assisted combustion: Effect of Sr2+ dopant
  7. Correlation of plastic deformation induced intermittent electromagnetic radiation characteristics with mechanical properties of Cu–Ni alloys
  8. Effect of isothermal quenching methods on impact toughness and wear resistance in high boron steel
  9. Wear behaviour of Al/(Al2O3 + ZrB2 + TiB2) hybrid composites fabricated by hot pressing
  10. Regression analysis of bonding strength of sprayed coatings based on acoustic emission signal
  11. Effect of substrates on covalent surface modification of graphene using photosensitive functional group
  12. Short Communications
  13. Investigation of optimum nucleation temperature and heating rate of cordierite glass-ceramics
  14. The influence of process parameters on the preparation of CaF2@Al(OH)3 composite powder via heterogeneous nucleation
  15. Effect of zirconium and heat treatment on the microstructure and properties of cast chromium bronze for conductive parts
  16. The influence of addition of citric acid on the physical properties of metallic oxide nanorods via Sol-Gel route preparation
  17. Notifications
  18. People
  19. DGM News
  20. Conferences
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 31.12.2025 from https://www.degruyterbrill.com/document/doi/10.3139/146.111165/pdf
Scroll to top button