Startseite Fatigue induced deformation of taper connections in dental titanium implants
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Fatigue induced deformation of taper connections in dental titanium implants

  • Simon Zabler , Tatjana Rack , Alexander Rack und Katja Nelson
Veröffentlicht/Copyright: 31. Mai 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 103 Heft 2

Abstract

The present study deals with in-situ microgap measurements in the internal taper connections of dental implants. Using X-ray phase contrast microtomography, the connecting interface between implant and abutment is probed non-destructively in three dimensions. Interference fringes across the conical interface occur due to the presence of microgaps, their intensity being a measure of the gap's width. Thus, for each point on the interface, interferences are extracted from the volumetric image in terms of normal projection maps which are, at selected points, compared to forward simulations to quantify the local gap width. Four designs of dental implants are tested in the “as-received” state as well as after application of cyclic extra-axial load. Results show different degrees of microgap opening by cyclic deformation according to the implants' design as well as a great amount of detail on the actual interface, i. e. fretting scars, grooves and wear debris.

Keywords: Microtomography; X-ray imaging; Phase-contrast; Dental implants; Fatigue
* Correspondence address Dr. Simon Zabler, Fakultät für Physik und Astronomie – LRM, Universität Würzburg, Am Hubland, D-97074 Würzburg, Germany, Tel.: +49 931/31-86 261, Fax: +49 931/31-85 507, E-mail:

References

[1] P.P.Binon: Int. J. Oral Maxillofac. Impl.1 (2000) 76.Suche in Google Scholar

[2] S.A.Hoyer, C.M.Stanford, S.Buranadham, T.Fridrich, J.Wagner, D.Gratton: J. Prosth. Dent.85 (2001) 599. 10.1067/mpr.2001.11525010.1067/mpr.2001.115250Suche in Google Scholar

[3] A.Khraisat, R.Stegaroiu, S.Nomura, O.Miyakawa: J. Prosth. Dent.88 (2002) 604. 10.1067/mpr.2002.12938410.1067/mpr.2002.129384Suche in Google Scholar

[4] M.A.Khan, R.L.Williams, D.F.Williams: Biomater.17 (1996) 2117. 10.1016/0142-9612(96)00029-410.1016/0142-9612(96)00029-4Suche in Google Scholar

[5] S.Fayeulle, P.Blanchard, L.Vincent: Tribol. Transact.2 (1993) 267. 10.1080/1040200930898315810.1080/10402009308983158Suche in Google Scholar

[6] M.R.Norton: Clin. Oral Implants Res.11 (2000) 458. 10.1034/j.1600-0501.2000.011005458.x10.1034/j.1600-0501.2000.011005458.xSuche in Google Scholar

[7] M.C.Cehreli, K.Akça, H.Iplikçioğlu: Clin. Oral Implants Res.15 (2004) 481. 10.1111/j.1600-0501.2004.01025.x10.1111/j.1600-0501.2004.01025.xSuche in Google Scholar

[8] Y.Hattori, C.Satoh, T.Kunieda, R.Endoh, H.Hisamatsu, M.Watanabe: J. Biomechanics42 (2009) 1533. 10.1016/j.jbiomech.2009.03.04010.1016/j.jbiomech.2009.03.040Suche in Google Scholar

[9] T.Morneburg, P.A.Proeschel: Int. J. Prosthodont.15 (2002) 20.Suche in Google Scholar

[10] B.R.Merz, U.C.Belser: Int. J. Oral Maxillofac. Impl.15 (2000) 519.Suche in Google Scholar

[11] M.R.Norton: J. Prost. Dent.83 (2000) 567. 10.1016/S0022-3913(00)70016-310.1016/S0022-3913(00)70016-3Suche in Google Scholar

[12] I.S.Park, S.Y.Won, T.S.Bae, K.Y.Song, X.W.Park, T.G.Eom, C.M.Jeong: Metals Mater. Int.14 (2008) 133. 10.3365/met.mat.2008.04.13310.3365/met.mat.2008.04.133Suche in Google Scholar

[13] K.Akça, M.C.Cehreli, H.Iplikçioğlu: Clin. Oral Implants Res.14 (2003) 444. 10.1034/j.1600-0501.2003.00828.x10.1034/j.1600-0501.2003.00828.xSuche in Google Scholar PubMed

[14] N.T.Green, E.E.Machtei, J.Horwitz, M.Peled: Implant Dentistry11 (2002) 137. 10.1097/00008505-200204000-0001410.1097/00008505-200204000-00014Suche in Google Scholar

[15] M.G.Manda, P.P.Psyllaki, D.N.Tsipas, P.T.Koidis: J. Biomed. Mater. Res. B: Appl. Biomater.89 (2009) 264. 10.1002/jbm.b.31211Suche in Google Scholar

[16] A.Piattelli, M.Piattelli, A.Scarano, L.Montesani: Int. J. Oral Maxillofac. Impl.13 (1998) 561.Suche in Google Scholar

[17] J.P.Aloise, R.Curcio, M.Z.Laporta, L.Rossi, A.M.da Silva, A.Rapoport: Clin. Oral Implants Res.21 (2010) 328. 10.1111/j.1600-0501.2009.01837.x10.1111/j.1600-0501.2009.01837.xSuche in Google Scholar

[18] P.G.Coelho, P.Sudack, M.Suzuki, K.S.Kurtz, G.E.Romanos, N.R.Silva: J. Oral Rehabil.35 (2008) 917. 10.1111/j.1365-2842.2008.01886.x10.1111/j.1365-2842.2008.01886.xSuche in Google Scholar

[19] S.Harder, B.Dimaczek, Y.Açil, H.Terheyden, S.Freitag-Wolf, M.Kern: Clin. Oral Investig.14 (2010) 427. 10.1007/s00784-009-0317-x10.1007/s00784-009-0317-xSuche in Google Scholar

[20] S.Dibart, M.Warbington, M.F.Su, Z.Skobe: Int. J. Oral Maxillofac. Impl.20 (2005) 732. 16274147Suche in Google Scholar

[21] V.K.Jansen, G.Conrads, E.J.Richter: Int. J. Oral Maxillofac. Impl.12 (1997) 527.Suche in Google Scholar

[22] M.Gross, I.Abramovich, E.I.Weiss: Int. J. Oral Maxillofac. Impl.14 (1999) 94.Suche in Google Scholar

[23] P.D.Miller, J.W.Holladay: Wear2 (1958) 133. 10.1016/0043-1648(58)90428-910.1016/0043-1648(58)90428-9Suche in Google Scholar

[24] K.G.Budinski: Wear151 (1991) 203. 10.1016/0043-1648(91)90249-T10.1016/0043-1648(91)90249-TSuche in Google Scholar

[25] R.M.Cibirka, S.K.Nelson, B.R.Lang, F.A.Rueggeberg: J. Prosthet. Dent.85 (2001) 268. 10.1067/mpr.2001.11426610.1067/mpr.2001.114266Suche in Google Scholar PubMed

[26] L.Steinebrunner, S.Wolfart, K.Ludwig, M.Kern: Clin. Oral Impl. Res.19 (2008) 1276. 10.1111/j.1600-0501.2008.01581.x10.1111/j.1600-0501.2008.01581.xSuche in Google Scholar PubMed

[27] W.Semper, S.Kraft, J.Mehrhof, K.Nelson: Int. J. Oral Maxillofac. Impl.25 (2010) 752.Suche in Google Scholar

[28] A.Rack, T.Rack, M.Stiller, H.Riesemeier, S.Zabler, K.Nelson: J. Synchrotron Radiat.17 (2010) 289. 10.1107/S090904951000183410.1107/S0909049510001834Suche in Google Scholar PubMed PubMed Central

[29] S.Zabler, T.Rack, A.Rack, K.Nelson: Rev. Sci. Instrum.81 (2010) 103703. 10.1063/1.349596610.1063/1.3495966Suche in Google Scholar PubMed

[30] T.Rack, S.Zabler, A.Rack, H.Riesemeier, K.Nelson: Submitted IJOMI (2011).Suche in Google Scholar

[31] A.Rack, S.Zabler, B.R.Müller, H.Riesemeier, G.Weidemann, A.Lange, J.Goebbels, M.Hentschel, W.Görner: Nucl. Instrum. & Meth. Phys. Res. A586 (2008) 327. 10.1016/j.nima.2007.11.02010.1016/j.nima.2007.11.020Suche in Google Scholar

[32] A.Mirone, R.Wilcke, A.Hammersley, C.Ferrero: PyHST – High Speed Tomographic Reconstruction (2011) http://www.esrf.eu/UsersAndScience/Experiments/TBS/SciSoft/.Suche in Google Scholar

[33] University of Wisconsin: Octave Homepage http://www.octave.org.Suche in Google Scholar

[34] S.Dittmer, M.P.Dittmer, P.Kohorst, M.Jendras, L.Borchers, M.Stiesch: J. Prosthodont.21 (2011) 510–516.10.1111/j.1532-849X.2011.00758.xSuche in Google Scholar PubMed

[35] N.Broggini, L.M.McManus, J.S.Hermann, R.Medina, R.K.Schenk, D.Buser, D.L.Cochran: J. Dent. Res.85 (2006) 473. 10.1177/15440591060850051510.1177/154405910608500515Suche in Google Scholar PubMed

[36] M.Taira, T.Kagiya, H.Harada, M.Sasaki, S.Kimura, T.Narushima, T.Nezu, Y.Araki: J. Mater. Sci.: Mater. Med.21 (2010) 267. 10.1007/s10856-009-3834-x10.1007/s10856-009-3834-xSuche in Google Scholar PubMed

Received: 2011-7-13
Accepted: 2011-11-16
Published Online: 2013-05-31
Published in Print: 2012-02-01

© 2012, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Exploiting Contrast with Tomography
  5. Original Contributions
  6. 3D imaging of complex materials: the case of cement
  7. Neutron Bragg-edge mapping of weld seams
  8. 3D image analysis and stochastic modelling of open foams
  9. In-situ X-ray microtomography study of the movement of a granular material within a die
  10. Synchrotron and neutron laminography for three-dimensional imaging of devices and flat material specimens
  11. Numerical correction of X-ray detector backlighting
  12. X-ray phase contrast and fluorescence nanotomography for material studies
  13. Estimation of the probability of finite percolation in porous microstructures from tomographic images
  14. Imaging of grain-level orientation and strain in thicker metallic polycrystals by high energy transmission micro-beam Laue (HETL) diffraction techniques
  15. Three-dimensional morphology and mechanics of bone scaffolds fabricated by rapid prototyping
  16. Fatigue induced deformation of taper connections in dental titanium implants
  17. Beyond imaging: on the quantitative analysis of tomographic volume data
  18. Damage fluctuations in creep deformed copper studied with synchrotron X-ray microtomography
  19. Neutron strain tomography using Bragg-edge transmission
  20. Three-dimensional registration of tomography data for quantification in biomaterials science
  21. Morpho-topological volume analysis of porous materials for nuclear applications
  22. People
  23. Professor Dr. rer. nat. Richard Wagner
  24. DGM News
  25. DGM News
https://doi.org/10.3139/146.110666
Schlagwörter für diesen Artikel
Microtomography; X-ray imaging; Phase-contrast; Dental implants; Fatigue

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Exploiting Contrast with Tomography
  5. Original Contributions
  6. 3D imaging of complex materials: the case of cement
  7. Neutron Bragg-edge mapping of weld seams
  8. 3D image analysis and stochastic modelling of open foams
  9. In-situ X-ray microtomography study of the movement of a granular material within a die
  10. Synchrotron and neutron laminography for three-dimensional imaging of devices and flat material specimens
  11. Numerical correction of X-ray detector backlighting
  12. X-ray phase contrast and fluorescence nanotomography for material studies
  13. Estimation of the probability of finite percolation in porous microstructures from tomographic images
  14. Imaging of grain-level orientation and strain in thicker metallic polycrystals by high energy transmission micro-beam Laue (HETL) diffraction techniques
  15. Three-dimensional morphology and mechanics of bone scaffolds fabricated by rapid prototyping
  16. Fatigue induced deformation of taper connections in dental titanium implants
  17. Beyond imaging: on the quantitative analysis of tomographic volume data
  18. Damage fluctuations in creep deformed copper studied with synchrotron X-ray microtomography
  19. Neutron strain tomography using Bragg-edge transmission
  20. Three-dimensional registration of tomography data for quantification in biomaterials science
  21. Morpho-topological volume analysis of porous materials for nuclear applications
  22. People
  23. Professor Dr. rer. nat. Richard Wagner
  24. DGM News
  25. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 30.10.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.110666/html?lang=de
Button zum nach oben scrollen