Startseite The influence of microstructural characteristics and contaminants on the mechanical properties and fracture topography of low cost Ti6Al4V alloy
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

The influence of microstructural characteristics and contaminants on the mechanical properties and fracture topography of low cost Ti6Al4V alloy

  • Dusan Bozic , Danijela Sekulic , Jelena Stasic , Viseslava Rajkovic und Milan T. Jovanovic
Veröffentlicht/Copyright: 11. Juni 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 99 Heft 11

Abstract

Low cost titanium alloy compacts were produced via the powder metallurgy approach through the hydride – dehydride process and hot consolidation (hot pressing and hot isostatic pressing). The conditions of the reversible hydride – dehydride process were determined by X-ray and scanning electron microscopy characterisation of powders. Powders were consolidated both above and below the β transformation temperature. The morphology of the microstructure, and the presence of open and closed pores, as well as residual particles of hydrides and oxides have a direct influence on the mechanical properties of compacts (tensile properties and impact toughness).

Keywords: Ti6Al4V; Hydride – dehydride process; Hot compacting; Microstructure of powders and compacts; Fracture surface; Tensile properties; Impact toughness
* Correspondence address, Dr Viseslava Rajkovic, Institute of Nuclear Sciences “Vinca”, P.O. Box 522, 11001 Belgrade, Serbia, Tel.: +381 11 24 39 45 4, Fax: +381 11 24 39 45 4, E-mail:

References

[1] R.R.Boyer: Mater. Sci. Eng. A213 (1996) 103.Suche in Google Scholar

[2] M.Mitkov, D.Bozic, in: 1994 Powder Metallurgy World Congress and Exhibition, Vol. 1, Paris (1994) 303.Suche in Google Scholar

[3] V.S.Ustinov, J.G.Olesov, B.A.Drozdenko, L.N.Antipin: Titanium Powder Metallurgy, Metallurgiya, Moscow (1981).Suche in Google Scholar

[4] G.R.Yoder, L.A.Cooley, T.W.Crooker: Eng. Frac. Mech.17 (1983) 185.Suche in Google Scholar

[5] R.K.Nalla, B.L.Bouce, J.P.Campbel, O.J.Peters, R.O.Ritchie: Metall. Mater. Trans. A331 (2002) 899.Suche in Google Scholar

[6] N.F.Anoskin: Metallografija titanovih splavov, Metallurgija, Moskva (1980).Suche in Google Scholar

[7] G.H.Chanani, W.T.Highberger, C.F.Kelto, V.C.Petersen, in: F.H.Froes, J.H.Smugersky (Eds.), Powder Metallurgy of Titanium Alloys, Las Vegas, Nevada (1980) 26.Suche in Google Scholar

[8] G.Lütjering, J.Williams, A.Gysler, in: J.C.M.Li (Ed.), Microstructure and Properties of Materials, Vol. 2, World Scientistic Publishing, Singapore (2000) 1.10.1142/9789812793959_0001Suche in Google Scholar

Received: 2007-10-27
Accepted: 2008-6-6
Published Online: 2013-06-11
Published in Print: 2008-11-01

© 2008, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Basic
  4. A model to calculate the viscosity of silicate melts
  5. A model to calculate the viscosity of silicate melts
  6. A note on the application of the phase rule
  7. Thermodynamic properties of liquid silver–indium–tin alloys determined from emf measurements
  8. Unconstrained solidification and characterisation of near-eutectic Al–Cu–Ag alloys
  9. Tensile properties of L12 intermetallic foils fabricated by cold rolling
  10. Microstructural control of FeB-inoculated mottled low-alloy white iron by a design of experiments approach
  11. Applied
  12. Dislocation structure and crystallite size distribution in lath martensite determined by X-ray diffraction peak profile analysis
  13. Effect of minor addition of Pb upon interfacial reactions and mechanical properties at Sn-3.0Ag-0.5Cu/Cu and Sn-58Bi/Cu solder joints
  14. Elastic properties of braided ceramic matrix composites
  15. The influence of microstructural characteristics and contaminants on the mechanical properties and fracture topography of low cost Ti6Al4V alloy
  16. Microstructure and room temperature mechanical properties of Hf and Sn-doped Nb-20Ti-5Cr-3Al-18Si alloy
  17. The effect of alloying elements on constrained carbon equilibrium due to a quench and partition process
  18. Hardfacing behavior of Cr–Ni stainless steel with Co-based super alloys
  19. Development of SMD 32.768 kHz tuning fork-type crystals
  20. Notification
  21. DGM News
https://doi.org/10.3139/146.101762
Schlagwörter für diesen Artikel
Ti6Al4V; Hydride – dehydride process; Hot compacting; Microstructure of powders and compacts; Fracture surface; Tensile properties; Impact toughness

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Basic
  4. A model to calculate the viscosity of silicate melts
  5. A model to calculate the viscosity of silicate melts
  6. A note on the application of the phase rule
  7. Thermodynamic properties of liquid silver–indium–tin alloys determined from emf measurements
  8. Unconstrained solidification and characterisation of near-eutectic Al–Cu–Ag alloys
  9. Tensile properties of L12 intermetallic foils fabricated by cold rolling
  10. Microstructural control of FeB-inoculated mottled low-alloy white iron by a design of experiments approach
  11. Applied
  12. Dislocation structure and crystallite size distribution in lath martensite determined by X-ray diffraction peak profile analysis
  13. Effect of minor addition of Pb upon interfacial reactions and mechanical properties at Sn-3.0Ag-0.5Cu/Cu and Sn-58Bi/Cu solder joints
  14. Elastic properties of braided ceramic matrix composites
  15. The influence of microstructural characteristics and contaminants on the mechanical properties and fracture topography of low cost Ti6Al4V alloy
  16. Microstructure and room temperature mechanical properties of Hf and Sn-doped Nb-20Ti-5Cr-3Al-18Si alloy
  17. The effect of alloying elements on constrained carbon equilibrium due to a quench and partition process
  18. Hardfacing behavior of Cr–Ni stainless steel with Co-based super alloys
  19. Development of SMD 32.768 kHz tuning fork-type crystals
  20. Notification
  21. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 23.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.101762/html?lang=de
Button zum nach oben scrollen