Startseite Wear resistance of laser cladded Stellite 31 coating on AISI 316L steel
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Wear resistance of laser cladded Stellite 31 coating on AISI 316L steel

  • Pisit Kittivitayakul , Jirapon Khamwannah , Patiphan Juijerm , Anchaleeporn Waritswat Lothongkum und Gobboon Lothongkum
Veröffentlicht/Copyright: 26. September 2018
Veröffentlichen auch Sie bei De Gruyter Brill
Manuskript einreichen Informationen für Autor*innen
Materials Testing
Aus der Zeitschrift Materials Testing Band 60 Heft 10

Abstract

Laser cladding of Stellite 31 powder on AISI 316L plate size of 50 × 50 × 25 mm using diode laser powers of 3.5, 4.0, 4.5 and 5.0 kW was produced. The wear tests of clad layers were investigated according to ASTM G99. Equiaxed and elongated grains were found in clad layer using laser powers of 3.5, 4.0 kW and 4.0, 5.0 kW, respectively. Compressive residual stress was detected at the surface of the clad layers. They decreased as laser power increased. After polishing, compressive residual stress and the wear resistance of the clad layers subjected to higher laser power were higher than those subjected to lower laser power. The friction coefficient of the clad layer subjected to higher laser power was lower than that subjected to lower laser power.

Kurzfassung

Mit einem Diodenlaser wurden bei Leistungen von 3,5, 4,0, 4,5 and 5,0 kW Schichten aus einem Stellite 31 Pulver auf eine Stahlplatte des Typs AISI 316L mit einer Größe von 50 × 50 × 25 mm aufgebracht. Es wurden Verschleißversuche entsprechend des ASTM-Standards G99 durchgeführt. In der Schicht wurden gleichmäßige und gelängte Körner bei den entsprechenden Laserleistungen von 3,5, 4,0, 4,5 and 5,0 kW gefunden. Es wurden außerdem die Druckeigenspannungen auf der Oberfläche der Schichten gemessen und sie nahmen mit zunehmender Laserleistung ab. Nach dem Polieren waren die Druckeigenspannungen und der Verschleißwiderstand der Schichten bei höheren Laserleistungen höher und bei niedrigeren Laserleistungen entsprechend geringer. Der Reibkoeffizient der Schichten, die mit höherer Laserleistung hergestellt wurden, war niedriger als bei niedrigeren Laserleistungen.

*Correspondence Address, Prof. Dr.-Ing. Gobboon Lothongkum, Department of Metallurgical Engineering, Faculty of Engineering, Chulalongkorn University, Patumwan, Bangkok 10330, Thailand, E-mail:

Pisit Kittivitayakul, born in 1991, is a graduate student in the Department of Metallurgical Engineering, Chulalongkorn University, Bangkok, Thailand. His research scope is related to the development and characterization of welding of superalloy. He received his Bachelor's degree in Metallurgical Engineering at Chulalongkorn University, Thailand in 2014. Currently, he is in service as an engineer at Five Tiger Engineering, Songkhla, Thailand.

Dr. Jirapon Khamwannah, born in 1983, is a lecturer in the Department of Metallurgical Engineering, Faculty of Engineering, Chulalonkorn University, Bangkok, Thailand. She received her PhD degree in 2015 at the University of California San Diego, USA. Her areas of expertise include developing nano-surface for biomaterials and energy related applications.

Dr.-Ing. Patipan Juijerm, born in 1973, is an Assistance Professor at the Department of Material Engineering, Faculty of Engineering, Kasertsart University, Bangkok, Thailand. He received his Dr.-Ing. degree at the University of Kassel, Germany. Mechanical and thermochemical surface treatments and residual stresses related to the fatigue performance of metallic materials are his area of expertise.

Associate Prof. Dr. Anchaleeporn Waritswat Lothongkum received her PhD in Hydrocarbon Chemistry in Catalyst Design Engineering at Kyoto University, Japan, in 1994, thanks to a Scholarship from the Hitachi Scholarship Foundation. She is an Associate Professor at King Mongkut's Institute of Technology Ladkrabang in Bangkok, Thailand. She served as President of the Thai Institute of Chemical Engineering and Applied Chemistry from 2013 to 2017. Her fields of interest are catalysis, clean technologies, alternative energy, sol gel technology, membrane technology, separation processes, environmental related, corrosion, wastewater treatment, adsorption engineering, electroplating, powder technology, and process safety management.

Prof. Dr.-Ing. Gobboon Lothongkum, born in 1960, is a member of the Innovative Metals Research Unit, Department of Metallurgical Engineering, Faculty of Engineering, Chulalongkorn University, Bangkak, Thailand. He has been serving as Head of the department since 2015. He received his Dr.-Ing. degree from the University of the Federal Armed Force Hamburg, Germany and the International Welding Engineer Certificate of the International Institute of Welding in 1994 and 2006, respectively. His areas of interest are corrosion of metals and alloys, welding and metal joining, stainless steel, high temperature materials and process safety management.

References

1 C. T.Sims: Cobalt-base alloys, C. T.Sims, W. C.Hagel (Eds.): The Superalloys, John Wiley & Sons, Inc., New York, USA (1972)Suche in Google Scholar

2 J. R.Davis & Associates: ASM Specialty Handbook: Nickel, Cobalt, and their alloys, ASM International, Materials Park, OH, USA (2000)Suche in Google Scholar

3 M. J.Donachie, S. J.Donachie: Superalloys: A Technical Guide, 2nd Ed., ASM International, Materials Park, OH, USA (2002)10.31399/asm.tb.stg2.9781627082679Suche in Google Scholar

4 B.Geddes, H.Leon, X.Huang: Superalloys: Alloying and Performance, ASM International, Materials Park, OH, USA (2010).10.31399/asm.tb.sap.9781627083133Suche in Google Scholar

5 https://www.cobaltinstitute.org/wear-resistant-alloys.html, accessed on May, 3, 2018Suche in Google Scholar

6 J.Lawrence, J.Pou, D. K. Y.Low, E.Toyserkani: Advances in laser materials Processing: Technology, Research and Applications, Woodhead Publishing Limited, Abington Hall, Granta Park, Great Abington, Cambridge, UK (2010)Suche in Google Scholar

7 http://www.praxairsurfacetechnologies.com/coating-services/application-processes/laser-processing, accessed on May, 3, 2018.Suche in Google Scholar

8 http://www.matweb.com/search/datasheet.aspx access on May 7, 2018.Suche in Google Scholar

9 S.Kapoor: High-Temperature Hardness and Wear Resistance of Stellite Alloys, MSc Thesis, Faculty of Graduate and Postdoctoral Affairs, Carleton University Ottawa, Ontario, Canada (2012)Suche in Google Scholar

10 http://www.calphad.com/cobalt-chromium.html, accessed on May 31, 2018.Suche in Google Scholar

11 Katsuji Tosha: Influence of residual stresses on the hardness number in the affected layer produced by shot peening, Proc. of the 2nd Asia Pacific Forum on Precision Surface Finishing and Deburring Technology, Seoul, Korea (2002), pp. 48–54Suche in Google Scholar

12 J.Frankel, A.Abbate, W.Scholz: The effect of residual stresses on hardness measurements, Experimental Mechanics, 33 (1993), No. 2, pp. 164–16810.1007/BF02322494Suche in Google Scholar

13 H.So, C. T.Chen, Y. A.Chen: Wear behaviours of laser-clad stellite alloy 6, Wear192 (1996), pp. 78–8410.1016/0043-1648(95)06769-8Suche in Google Scholar

14 K.Kato: Classification of wear mechanisms/models: W.Gwidon, W.Stachowiak (Eds.): Wear – Materials, Mechanisms and Practice, John Wiley & Sons Ltd, Chichester, UK (2005)Suche in Google Scholar

Published Online: 2018-09-26
Published in Print: 2018-10-27

© 2018, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Inhalt/Contents
  2. Contents
  3. Laudatio
  4. Professor Dr.-Ing. Harald Zenner: on the occasion of his eightieth birthday
  5. Fachbeiträge/Technical Contributions
  6. Fatigue life curve – A continuous Wöhler curve from LCF to VHCF
  7. On the accuracy of estimating fatigue notch factors
  8. Analytical strength assessments of austempered ductile iron components
  9. On the estimation of cyclic material properties – Part 1: Quality of known estimation methods
  10. On the estimation of cyclic material properties – Part 2: Introduction of a new estimation method
  11. Execution and evaluation of cyclic tests at constant load amplitudes – DIN 50100:2016
  12. Wear resistance of laser cladded Stellite 31 coating on AISI 316L steel
  13. Determination of the Johnson-Cook damage parameter D4 by Charpy impact testing
  14. Effect of residual Alclad on friction stir spot welds of AA2219 alloys
  15. Effect of cooling rate on microstructure, mechanical properties and residual stress of 7075 aluminum alloy
  16. Failure analysis of an adhesively joined composite pipe system under internal pressure
  17. Non-metallic inclusions and fatigue strength of steel 34CrNiMo6
  18. Untersuchungen des Schädigungsgrades von Polyethylenformstoffen als Werkstoffe von Heizöllagerbehältern nach einer Nutzungsdauer von über 30 Jahren
  19. Microstructure and mechanical properties of AZ31 Mg alloy produced by a new compound extrusion technique
  20. Failure analysis of a cracked Q125 casing for ultra-deep wells at the Tarim Oilfield
https://doi.org/10.3139/120.111239

Artikel in diesem Heft

  1. Inhalt/Contents
  2. Contents
  3. Laudatio
  4. Professor Dr.-Ing. Harald Zenner: on the occasion of his eightieth birthday
  5. Fachbeiträge/Technical Contributions
  6. Fatigue life curve – A continuous Wöhler curve from LCF to VHCF
  7. On the accuracy of estimating fatigue notch factors
  8. Analytical strength assessments of austempered ductile iron components
  9. On the estimation of cyclic material properties – Part 1: Quality of known estimation methods
  10. On the estimation of cyclic material properties – Part 2: Introduction of a new estimation method
  11. Execution and evaluation of cyclic tests at constant load amplitudes – DIN 50100:2016
  12. Wear resistance of laser cladded Stellite 31 coating on AISI 316L steel
  13. Determination of the Johnson-Cook damage parameter D4 by Charpy impact testing
  14. Effect of residual Alclad on friction stir spot welds of AA2219 alloys
  15. Effect of cooling rate on microstructure, mechanical properties and residual stress of 7075 aluminum alloy
  16. Failure analysis of an adhesively joined composite pipe system under internal pressure
  17. Non-metallic inclusions and fatigue strength of steel 34CrNiMo6
  18. Untersuchungen des Schädigungsgrades von Polyethylenformstoffen als Werkstoffe von Heizöllagerbehältern nach einer Nutzungsdauer von über 30 Jahren
  19. Microstructure and mechanical properties of AZ31 Mg alloy produced by a new compound extrusion technique
  20. Failure analysis of a cracked Q125 casing for ultra-deep wells at the Tarim Oilfield
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 1.10.2025 von https://www.degruyterbrill.com/document/doi/10.3139/120.111239/html
Button zum nach oben scrollen