Development of a cavity pressure control for injection moulding by adjusting the cross-section in the hot runner
-
Christian Hopmann
und
Hanna Dornebusch
Abstract
Fluctuations in the injection moulding process are affecting component quality. A pressure control can be used to increase process consistency. However, current control systems cannot influence the melt flow in the mould specifically for individual cavities. Therefore, a control concept is being developed in which commercially available, servo-electrically driven hot runner valve pins are used to control the cavity pressure in the holding pressure phase. By varying the stroke, the pressure resistance in the hot runner and thus the pressure transfer into the cavity are influenced. A one cavity mould with two pressure sensors and a servo-electrical driven hot runner was used to evaluate the control setup, implementing a PID controller. The evaluation criterion for the setup is to what extent the reference curve measured in advance can be reproduced after provoked disturbance. The control calculates the difference between the actual pressure and the reference curve. The control compensates the pressure difference by a pin movement. The control concept can compensate for disturbances that do not change the material behaviour, such as changes in holding pressure. Changes in the material behaviour, for example due to fluctuations in the mould temperature, cannot be compensated due to the reference control.
-
Author contribution: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Research funding: The research project 19966N of the Forschungsvereinigung Kunststoffverarbeitung was sponsored as part of “industrielle Gemeinschaftsforschung und -entwicklung (IGF)” by the German Bundesministerium für Wirtschaft und Energie (BMWi) due to an enactment of the German Bundestag through the AiF. We would like to extend our thanks to all organizations mentioned.
-
Conflict of interest statement: The authors declare no conflicts of interest regarding this article.
References
1. König, E. Innovative möglichkeit zur qualitätssicherung von spritzgussbauteilen auf basis von werkzeuginnendruck und werkzeugwandtemperatur. In Fachtagung Spritzgießen und Veredeln, Duisburg, Germany, 2014.Suche in Google Scholar
2. Schiffers, R. Robuste spritzgießprozesse mit adaptiver prozessführung als basis für eine effiziente produktion hochwertiger formteile. In Fachtagung Spritzgießen und Veredeln, Duisburg, Germany, 2014.Suche in Google Scholar
3. Behrens, H.-H. Null-fehler-produktion statt kontrolle. Kunststoffxtra 2015, 105, 19–22.Suche in Google Scholar
4. Brinkmann, T. Produktentwicklung Mit Kunststoffen; Carl Hanser Verlag: Munich, Vienna, 2008.Suche in Google Scholar
5. Kruppa, S. Improved process and component quality when using recycled materials. Kunstst. Int. 2017, 107, 26–27.Suche in Google Scholar
6. Schiffers, R. Adaptive process control – what is it for? Kunstst. Int. 2017, 107, 29–30.Suche in Google Scholar
7. Heinzler, F. A., Wortberg, J. Qualitätsregelung beim spritzgießen (teil1): rheologische untersuchung prozessrelevanter alterungseinflüsse. Z. Kunststofftechnik 2015, 11, 103–130, https://doi.org/10.3139/o999.03022015.Suche in Google Scholar
8. Bader, C. Quality rarely comes alone. Kunstst. Int. 2015, 105, 27–32.Suche in Google Scholar
9. Schiffers, R. How are viscosity changes detected and corrected? Kunstst. Int. 2017, 107, 45–46.Suche in Google Scholar
10. Hornberg, K., Hopmann, C., Vukovic, M., Stemmler, S. A. D. Effects of cyclical process influences on the cavity pressure curve and part quality in the injection moulding process. J. Plast. Technol. 2021, 17, 173–203.Suche in Google Scholar
11. Johannhaber, F., Michaeli, W. Handbuch Spritzgießen; Carl Hanser Verlag: Munich, 2004.10.3139/9783446440982Suche in Google Scholar
12. Heinzler, F. Modellgestützte Qualitätsregelung Durch Eine Adaptive, Druckgeregelte Prozessführung beim Spritzgießen. Ph.D. Thesis, Universität Duisburg-Essen, Germany, 2014.10.3139/O999.02032015Suche in Google Scholar
13. Schiffers, R. Verbesserung der Prozessfähigkeit beim Spritzgießen Durch Nutzung von Prozessdaten und Eine Neuartige Schneckenhubführung. Ph.D. Thesis, Universität Duisburg-Essen, Germany, 2009.Suche in Google Scholar
14. Eben, J. Identifizierung und Reduzierung Realer Schwankungen Durch Paxistaugliche Prozessführungsmethoden beim Spritzgießen. Ph.D. Thesis, Technische Universität Chemnitz, Germany, 2014.Suche in Google Scholar
15. Kurt, M., Kamber, S. O., Kaynak, Y., Atakok, G., Girit, O. Experimental investigation of plastic injection molding: assessment of the effects of cavity pressure and mold temperature on the quality of the final products. Mater. Des. 2009, 30, 3217–3224, https://doi.org/10.1016/j.matdes.2009.01.004.Suche in Google Scholar
16. Schreiber, A. Regelung des Spritzgießprozesses auf Basis von Prozessgrößen und im Werkzeug ermittelter Materialdaten. Ph.D. Thesis, RWTH Aachen, Germany, 2011.Suche in Google Scholar
17. Kruppa, S. Adaptive Prozessführung und Alternative Einspritzkonzepte beim Spritzgießen von Thermoplasten. Ph.D. Thesis, Universität Duisburg-Essen, Germany, 2015.Suche in Google Scholar
18. Pillwein, G., Giessauf, J., Steinbichler, G. Einfaches Umschalten auf konstante Qualität. Kunststoffe 2012, 102, 31–35.Suche in Google Scholar
19. Bader, C., König, E., Schmidt, C. Qualität aus der Tiefe des Werkzeugs. Kunststoffe 2013, 103, 46–50.Suche in Google Scholar
20. Bader, C. Verfahren zum Überwachen und/oder Regeln der Schmelzebefüllung von zumindest einer Kavität. Patent specification. DE102005032367A1, Germany, 2005.Suche in Google Scholar
21. Behr, H., Graf, H., List, H., Mayer, F. Regeleinrichtung fuer Spritzgussmaschinen. Patent specification DE2358911A1, 1972.Suche in Google Scholar
22. Bader, C., König, E. Wir regeln das schon. Kunststoffe 2012, 102, 62–67.Suche in Google Scholar
23. Schäfer, O. Geregelte teilequalität. In Today, Das ARBURG Magazin, Vol. 35, 2007; p. 19.Suche in Google Scholar
24. Schnerr-Häselbarth, O. Der heiße draht ins werkzeug. Kunststoffe 2002, 92, 56–60.Suche in Google Scholar
25. Bader, C. Und sie bewegt sich doch. Kunststoffe 2008, 98, 60–66.Suche in Google Scholar
26. Bader, C., Kristiansen, P. M. Auf den Punkt gebracht. Kunststoffe 2011, 101, 16–20.Suche in Google Scholar
27. Michaeli, W., Gruber, J. Prozessführung beim Spritzgießen – direkte Regelung des Werkzeuginnendrucks steigert die Reproduzierbarkeit. Z. Kunststofftechnik 2005, 1, 1–12.Suche in Google Scholar
28. Michaeli, W., Schreiber, S. Der Innendruck im Fokus der Regelung – Prozessführung beim Spritzgießen auf Basis von Prozessgrößen. Plastverarbeiter 2008, 35, 30–33.Suche in Google Scholar
29. Michaeli, W., Schreiber, A., Lettowsky, C. Optimierung der Prozessführung beim Thermoplastspritzgießen durch online-Regelung auf Basis von Prozessgrößen. Z. Kunststofftechnik 2008, 4, 1–17.Suche in Google Scholar
30. Michaeli, W., Schreiber, A. Online control of the injection molding process based on process variables. Adv. Polym. Technol. 2009, 28, 65–76 https://doi.org/10.1002/adv.20153.Suche in Google Scholar
31. Theunissen, M., Hopmann, C., Heinisch, J. Compensating viscosity fluctuations in injection moulding. In Polym. Proc. Soc., PPS-32 Conf. Proc Lyon, France, 2016.10.1063/1.5016748Suche in Google Scholar
32. Gruber, J. M. Prozessführung beim Thermoplastspritzgießen auf Basis des Werkzeuginnendrucks. Ph.D. Thesis, RWTH Aachen, Germany, 2005.Suche in Google Scholar
33. Hopmann, C., Reßmann, A., Heinisch, J. Influence on product quality by pvT-optimised processing in injection compression molding. Int. Polym. Process. 2016, 31, 156–165, https://doi.org/10.3139/217.3058.Suche in Google Scholar
34. Hopmann, C., Abel, D., Heinisch, J., Stemmler, S. Self-Optimizing Injection Molding Based on Iterative Learning Cavity Pressure Control; Springer Verlag: Heidelberg, 2017.10.1007/s11740-017-0719-6Suche in Google Scholar
35. Schreyer, H -J. Verfahren überschreitet bisherige Grenzen beim Spritzgießen. Kunststoffe, 2005, 95, 48–49.Suche in Google Scholar
36. Doughty, M., Frisin, W., Hume, W., Kazmer, D., Moss, M. Controlled Injection using Manifold having Multiple Feed Channels. Patent specification. US2003/0203064A1, USA, 2003.Suche in Google Scholar
37. Kazmer, D. O., Barkan, P. Multi-cavity pressure control in the filling and packing stages of the injection molding process. Polym. Eng. Sci. 1997, 37, 1865–1879, https://doi.org/10.1002/pen.11837.Suche in Google Scholar
38. Kazmer, D. O. Dynamic Feed Control: A New Method for Injection Molding of High Quality Plastic Parts. Ph.D. Thesis Dissertation, Stanford University, California, USA, 1995.Suche in Google Scholar
39. Kazmer, D. O., Gupta, D. A low force valve for dynamic control of molten plastics in a mold. Int. Polym. Process. 2006, 21, 175–182, https://doi.org/10.3139/217.0094.Suche in Google Scholar
40. Kazmer, D. O., Barkan, P. The process capability of multi-cavity pressure control for the injection molding process. Polym. Eng. Sci. 1997, 37, 1880–1895, https://doi.org/10.1002/pen.11838.Suche in Google Scholar
41. N.N. Die Größten ihrer art. Kunststoffe 2018, 108, 85.Suche in Google Scholar
42. Hopmann, C., Dornebusch, H. Werkzeuginnendruck in der nachdruckphase regeln. Plastverarbeiter 2019, 70, 108–110.Suche in Google Scholar
43. Hopmann, C., Dornebusch, H., Schöll, M. Die heißkanalnadel als stellgröße. Kunststoffe 2021, 111, 34–37.Suche in Google Scholar
44. Ziegler, J. G., Nichols, N. B. Optimum settings for automatic controllers. J. Dyn. Syst. Meas. Control Trans. ASME 1942, 64, 759–765.10.1115/1.2899060Suche in Google Scholar
© 2022 Walter de Gruyter GmbH, Berlin/Boston
Artikel in diesem Heft
- Frontmatter
- Material Properties
- Advancement in hemp fibre polymer composites: a comprehensive review
- Effects and mechanism of filler content on thermal conductivity of composites: a case study on plasticized polyvinyl chloride/graphite composites
- Effects of Eucommia ulmoides gum content and processing conditions on damping properties of E. ulmoides gum/nitrile-butadiene rubber nanocomposites
- Preparation and Assembly
- Preparation of flame retardant glass fiber via emulsion impregnation and application in polyamide 6
- Invertase adsorption with polymers functionalized by aspartic acid
- Engineering and Processing
- External field alignment of nickel-coated carbon fiber/PDMS composite for biological monitoring with high sensitivity
- Development of a cavity pressure control for injection moulding by adjusting the cross-section in the hot runner
- Process optimization for extraction of avian eggshell membrane derived collagen for tissue engineering applications
- Joint formation mechanism of different laser transmission welding paths
Artikel in diesem Heft
- Frontmatter
- Material Properties
- Advancement in hemp fibre polymer composites: a comprehensive review
- Effects and mechanism of filler content on thermal conductivity of composites: a case study on plasticized polyvinyl chloride/graphite composites
- Effects of Eucommia ulmoides gum content and processing conditions on damping properties of E. ulmoides gum/nitrile-butadiene rubber nanocomposites
- Preparation and Assembly
- Preparation of flame retardant glass fiber via emulsion impregnation and application in polyamide 6
- Invertase adsorption with polymers functionalized by aspartic acid
- Engineering and Processing
- External field alignment of nickel-coated carbon fiber/PDMS composite for biological monitoring with high sensitivity
- Development of a cavity pressure control for injection moulding by adjusting the cross-section in the hot runner
- Process optimization for extraction of avian eggshell membrane derived collagen for tissue engineering applications
- Joint formation mechanism of different laser transmission welding paths
